Ford Transmission :: Take Off Output Flange Without Changing Tail Shaft?
Oct 2, 2015
Can I take off the output flange on the tranny and use a slip joint, with out changing the tail shaft?
View 1 Replies
Oct 2, 2015
Advertisement
Ford Excursion :: Transmission Output Shaft Play Slightly Up And Down - Torque Specification?
I removed my drift shaft to get balanced since I have felt a vibration at 55-60 mph. After removing the driveshaft I noticed there is some play in the output shaft when I grab a hold of the yoke on the transmission. The play is a slightly up and down. If my memory serves me right that should not be. Seal is not leaking but need diagram of this yoke off the output shaft. I know in past on other vehicles there is sometimes a crush washer. Also what is the torque specification for that output shaft nut?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Transmission Output Shaft Seal Removal
I'm trying to replace my transmission output shaft seal on my 2wd and I can't seem to get the seal removed. I couldn't find anything to rent from O'rielly's or Advance Autoparts that would work. It's in there really tight ....
View 10 RepliesAccent LC (2000-05) :: Code For Output Shaft Speed Sensor - Transmission Rebuild
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 RepliesFord Transmission :: Small Leak Around Tail Shaft Seal
I got a fmx mated to 351w, trans was on back of a 302 and no problems other than small leak around tail shaft seal but shifted great. Now I decided to install mildly built 351w so figured it'd be a good time to build tranny. Installed after build and immediately it was slipping. Pulled trans out took it back to shop and he said the forward seal was blown. Installed again, after about 15 miles same result! What could be causing this. It is fine in reverse, but slips bad in forward gears.
View 2 RepliesFord Aerostar :: Transmission Has Vibration Damper Mounted To The Lower Side Of Tail Shaft With 3 Bolts?
On my ongoing project, I have a replacement trans out of an Explorer. I have swapped over the bracket and will be changing the shifter shaft, but I noticed that the new trans has what appears to be some sort of vibration damper mounted to the lower side of the tail shaft with 3 bolts.
It is just a bracket that has a cast weight mounted in rubber. It was not a mount of any kind as the only bolt connection is to the trans itself.
The trans I took out did not have one of these, nor can I find any mention of it in the factory manual. The Explorer I pulled the trans from was a 92, my Aerostar is a 91. It doesn't appear that this device will conflict with mounting.
It is possible that the whoever installed the trans that I have removed forgot to install the damper, or it is possible that it is used only on the Explorer but not on the Aerostar.
Passat (B5) :: Gear Lube Leaking To The Passenger Side Output Flange Seal
My wifes car started leaking gear lube in the driveway. I traced the leak to the passenger side output flange seal. At first I thought the cause was a bad CV joint but when I tried to shake the axle, I noticed the whole flange moving...How can this be repaired? Does the whole tranny need to be removed or just the output pod?
View 4 RepliesFord Ranger / B-Series :: 1999 - Output Shaft Seal Won't Stay?
I replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.
99 2.5 auto. I changed the trans pan gasket too. No leaks from it.
Ford Excursion :: P0720 Code - Output Shaft Speed Sensor
Okay, I have a P0720 code. I bought the Output Shaft Speed Sensor and read that it is on the back end of the transmission.
Need to confirm that it is on top of the transmission, near the tail end? Why are parts that go bad always in the most inconvenient places?
Ford Excursion :: Stall Out At Almost Every Stop Light / Code P0720 - Output Shaft Speed Sensor?
I just replaced my starter and on my first ride after replacing it the X started to stumble a bit, and then would stall out at almost every stop light. It threw a CE light and I pulled the code P0720. I searched here and it seems most guys say this is a C.O.P. issue. If it is a bad C.O.P. would it stall like that?
I did have the battery disconnected but I made sure the terminals were clean and tight. Is this a coincidence or did I do something while changing the starter?
Celica :: 2000 GT - New Output Shaft Seal Leaks
I installed a JDM 2ZZ-GE engine and 6 speed manual trans-axle into my 2000 Celica GT.
I have ran into a interesting problem. I replaced the output shaft seals and now whenever the car is in the air and the suspension is unloaded (the drive axle is pulled slightly from the trans) the drivers side seal leaks a bit of gear oil. The drive axle is snapped into place. Nothing leaks when the car is on the ground.
I did reuse the old drive axles, which had a lot of miles on them but still appeared good and useable. I have been told to replace the new seal because it may be damaged, but I am wondering if it may be that the drive axle end is worn.
I have seen this with harmonic balancers for engines. They even sell a replacement sleeve for harmonic balancers so you can re-use the old worn one.
Lexus GX 2010+ :: Front Differential Leaking From Drive Shaft Output
My front diff appears to be leaking from the drive shaft output. it's not enough to leave drips but the skid plates are oily. Having the dealer look next week. 60k on a 2011 460.
View 3 RepliesCorolla / Matrix 2009-13 :: Tranny Output Shaft Bearing Gone At 67000 Miles
So my girlfriend got this car (2013 corolla s) a few months ago and we started hearing a funny noise, I thought it was a wheel bearing going but nope its the ouput bearing on the tranny, passenger side. is this common on corrollas? how hard is it to change? I have a tranny from an 06 corolla, are they the same? and could i just swap trannies if changing the bearing is too difficult?
View 2 RepliesYaris/Scion & Vitz :: 2001 Toyota Echo - Output Shaft Bearing Making Noise
I have a 2001 Toyota echo 2001 210.200 km and my output shaft bearing makes noise and I cant know the level of my transmission fluid bcoz I don't have dipstick and i bought trans 75w90 oil os that ok and how can I add this?
View 1 RepliesFord F-150 (2004-2008) :: 2007 V6 - Auto Tail Shaft Replacement
I'm working on a 2007 F150 V6 with a 4 speed automatic.. which seems to be a 4R70W. It has 36,xxx miles on it and the transmission tailshaft is cracked by the mount and leaking fluid.
The tailshaft can be replaced by itself without disassembling and removing the whole transmission right? The part number/Ford Engineering number on it is "RF-F3LP-7A040-AA" and it says 42A below that. Can I look for any tailshaft or just this number? F3 is a 1993 number isn't it? I don't know the length of it but it doesn't have a hole for a speedo cable.
Ford Super Duty (1999-2016) :: Drive Output Ratio From The Transmission?
I just purchased a F250 Gasser with the 6.2. I made sure to get it with the 4.30 rear to babl to tow a little better when i upsize the tires a little. Where I can find the drive output ratio from the transmission?
View 2 RepliesFord Transmission :: 1998 F250 - Code P0720 For Output Speed Sensor Circuit - No Reverse
I bought late 98 F-250, 5.4 G, 4WD. OHad to replace the steering flange because they messed up the ignition cylinder and flange. Truck didn't run for 4 years. 249K miles, no history available. Got the engine running, no DTCs. D, 3, 2, 1 barely moved the truck forward but, R hauled butt in reverse. Checked transmission fluid it was good and clean.
Came back to it a few days later it threw a P0720 (output speed sensor circuit) and I have no reverse, park feels like it wants to move, R is neutral, N is forward, D is forward, 3 is forward, 2 is forward, 1 is forward. The N is full drive. I cleared the P0720 code after it came up and it has not returned. The instrument gauges work but the odometer display is intermittent. Linkage? Fluid? Sensor? Wires?
Ford Super Duty (1999-2016) :: Overfilled Transfer Case Or Leaking Transmission Output Seal
I just changed transfer case fluid on my father's F-350 for the first time in 13 years. (over 230k). Removed fill plug first and fluid gushed out of the fill hole unexpectedly. Did not have catch pan ready, so made a mess. I thought it was just over filled form the factory, but too much was coming out to be simple overfill. Almost 2 qt came out of the fill plug.
Did some google search and found many Ford trucks have failed transmission output shaft seal and transmission fluid leaks out to transfer case, causing transfer case to overfill. I am yet to check transmission fluid level, but considering how much came out of it that probably is the case.
Now, how bad of the problem this really is? Will overfilled transfer case cause some serious problem? 4x4 is rarely used (once or twice a year in winter) on this truck and from what I understand transfer case doesn't really do anything in 2WD other than just passing output from transmission through.
There are no fluid leaking outside and repairing the seal would be a too much of work for me.
Also changed rear differential fluid for the first time and I was surprised how clean the fluid was. There were thin layer of black sticky residue (sludge?) covering everything, but the fluid itself looked clean and no visible metal shavings. I guess that is why Ford said it does not require change under normal condition.
Ford Transmission :: Drums Seized Onto Axle Shaft
I purchased a 1964 9 inch from a Galaxie 500 to use in my 51 merc M1. The drums were seized onto the axle shaft and after trying everything, I was forced to break them up with a sledge to get them off. The axles turn freely and I have removed the 4 bolts that hold the shafts to the housing flanges. The axles should slide right out but the do not. Am I missing something? How do I pull them if they don't budge?
View 1 RepliesGolf IV / Jetta IV :: Location Of Transmission Input And Output Sensors
My gf's son has an old 2000 Jetta 2.0 and when the check engine light came on and shifted poorly, it was diagnosed as a problem with the transmission input and/or output sensors. Where are they located exactly?
Both look pretty much the same, but here's a pic of one of them : [URL] ....
Ford - Ranger :: 1997 - Transmission Rebuild / How To Take The Input Shaft Out
I have a 1997 ford ranger 4x4 5 speed manual. We are rebuilding the transmission ourselves, and taking on the task has been pretty hard. We are stuck at the input shaft. How to take the input shaft out? Do you need a special tool?
View 1 Replies