Ford Transmission :: RPMs Drop And Truck Dies As Soon As Put It In Drive Or Reverse
Sep 21, 2016
Just finished putting a fresh 460 backed by a (1977) c6 in my '68 ranger and now I'm having (what I believe is) transmission problems. The truck will idle and rev properly in gear but as soon as I put it in drive or reverse the RPM's drop and it dies. I jacked the back end up and put it in both drive and reverse and the tire's spin, but if I try and apply the brake to stop them the truck will die. My suspicion is that the torque converter is locked up all the time. I have managed to get it in gear and give it gas and it'll drive and shift fine, until I come to a stop. My question, what would cause the converter to do this? It's the same transmission and converter that I pulled out a month ago and I never had any issues before...
View 4 Replies
Advertisement
I have a 2008 Elantra GLS. I am getting a code of P0750. Seloniod A fault. I have checked wiring harness for critter bites all looks good. If I clear the code the transmission shifts normal until it is shut off like overnight. I also have been noticing that it idles around 1100RPM to 1300RPM and it does drop into gear harder (reverse or drive). This high idle started before the P0750 code.
View 4 Replies
My truck does not go into reverse but thinks all positions of shifter are drive. I had some slippage and changed the filter and oil great for awhile then blame no reverse just forward I was told my torque converter was out I just don't know....
View 1 Replies
Well I am not sure if i have trans problem or not. If I put the trans in drive and go through the gears when the RPM's get to about 2000 the truck almost stops accelerating, until you give it much more gas, this happens in every gear. but If you push the button to take it out of overdrive and drive like that it doesn't do it.
View 1 Replies
I own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.
View 4 Replies
'99 Intrigue (3.5L) with 65k miles. The car has sporadic starting problems where turning the key in the ignition turns the starter motor and results in one of the following scenarios:
1) The engine does not turn on.
2) The engine turns on, RPMs drop and the engine sputters and dies.
3) The engine turns on with no problems (like this morning).
It does not appear to matter whether the engine is hot or cold.
Reading forum posts of people that have seen similar problems, several different solutions would seem to be in order:
1) Replace fuel pressure regulator.
2) Replace crankshaft position sensor
3) Replace camshaft position sensor
4) Replace fuel filter
5) Replace spark plugs
6) Replace idle air control valve
7) Clean the throttle body
Since I rather not start throwing money at the car by replacing parts one by one until the problem is gone.
View 11 Replies
I have a 1999 Camry. I just spent $1250 (half of it borrowed) to have some basic maintenance, diagnosis, and serious repair work done. More than half of the serious (translate: expensive) work involved replacing a charcoal canister and installing a thermostat. The check engine light had been on for at least 10 years. And I had a gas pumping problem by way of the pump shutting off after only pumping a few cents worth of gas. Needless to say it was a royal PIA to fuel up my car. As far as the check engine light, a friend would clear the code so I could have it inspected.
Then more than 2 years a shop took out my thermostat because a hose had sprung a leak and they rigged up a temporary hose until they could order the part. I never went back because I couldn't afford it. I know it wouldn't have been a terribly expensive repair, but at the time it was more than I could afford. So for almost 3 years I have driven with out a thermostat and also couldn't get it inspected.
Fortunately I was finally able to get the necessary repair on my car--replacing the charcoal canister and thermostat--so that it could be inspected. I picked the car up yesterday and everything felt fine and the car ran fine.
Today I drove it about 12 miles from my home, made 3 back-to-back errand stops of not more than 15-20 minutes each and everything seemed fine. Nothing felt or sounded out of the ordinary. Then when I was leaving my 3rd stop, the car would not start unless I gave it gas. And it wouldn't stay started unless I gave it gas. In other words, the car would go, but as soon as I would take my foot off the gas to press the brake to put it in gear, the engine would die. There was no problem restarting it as long as I gave it gas, but I could not let off the accelerator at all or it would immediately die.
The car would go just fine, but if I let off the gas for any reason, even if I was driving 40 miles an hour on the street and let up completely off on the accelerator, the rpms would immediately drop to 0 and the engine would immediately die---no noise, no shuttering, no nothing---just die. This problem occurred almost the whole 12 miles back to my home. Then when I got about a mile and a half away, it went back to behaving completely normal and did not die when I let off the gas.
View 10 Replies
I have a 1997 forkd F150 with a 4.6L Romeo engine. I have recently rebuilt the engine and now since it is put back together I am having a issues that i cannot pin point. When the truck is running and in gear my RPM drop to around 500 or below and my oil pressure drops and comes back up when the rpm's come back up this an intermittent problem and I have replaced the IAC valve and every once in a while i get a P0401 code for the exhaust recirculation. I think I am loosing some kind of vacuum. It was not doing this when I tore into the truck. It seems to be running okay not hesitation.
View 2 Replies
I think it's possessed! My sisters vehicle, a 2002 Explorer with a 4.0 V-6, automatic, 2 wheel drive will just shut off. At first it acted like it would vapor lock. But it would start right away. then the a while later, (several months), it got where it would drop rpms and the engine shudders, sometimes not dying.
When this first started, the throttle body was cleaned, a new air filter installed, fuel pressure checked. Everything checked out and for a few days it ran fine. Then it started all over again. There has never been a code thrown. All of this goes on only when the ambient temp is above 70 deg.'s. below 70 deg.'s it runs perfect.
Last week it went to the mechanic again and a new crank speed sensor, fuel pump, and diagnostic done. He could not find anything wrong any where. Took it for a test drive and it dyed on the mechanic. Still no codes. What the problem might be? Every Mechanic that has looked at it has gave up, one even saying, " it's possessed."
View 14 Replies
Cold start. engine starts but wont idle, just dies. rpms drop. Restart same. Must neutral drop to get going keep rpms up until engines shifts then things are fine until next cold start. Cleaned throttle, changed air filter, dry gas, injector cleaner, no warning signal, scans clean. 180k miles.
View 6 Replies
Its a 1999 f250sd 5.4l auto. Has code p1747. Truck shudders and almost dies when you drop it in gear, put it back in park idles fine. I have read all the post on here about this and checked wires from trans up to pcm look and test good. Tested plug c1048 wires with digital meter to body ground with battery unhooked and got 6.66k ohms on pin 11 circuit 925, 421 ohms pins 1 and 12. Plugged c1048 back to trans checked 925 w/y wire at plug c103 got 9.1 ohms back to trans. Is the epc solenoid bad or is it pcm. I think its epc but want to verify before i take trans apart.
View 3 Replies
I'll try not to post an entire book.. But I bought a 2000 F250 not even 8 months ago, it did have issues before but I changed out the spark plugs and coils and it fixed it's original missing issues.. I also just recently changed the fuel filter but it didn't fix it's new problem.. It drives ok around town but if I get over 35 mph it doesn't run well... If I try to keep a steady foot on the gas but don't get the RPMs over 2000, the RPMs will stay where they're at for just a second then they will drop down and the whole truck starts shaking.. I push more on the gas and it shakes even more and the RPMs don't move at all until I really step on it.. It lacks in power going up hills as well... The dealership i bought it from said the Catalytic Converter was bad but my uncle who is a mechanic says it isn't.. It's the first vehicle I've bought so kinda wanna make it last..
View 11 Replies
I have a 1997 F-150, 2 wheel drive, 4.6L truck. Recently the transmission got to where it didn't shift properly. Then it got to where, after driving it about 10 to 15 miles the transmission would drop out of gear with the transmission selector in drive.
I have replaced the transmission sensor, the rear end sensor and it still does the same thing. Drive about 10 to 15 miles and, with the transmission selector in drive the truck will not pull. The motor can be rev'ed but the truck won't move just like it was in neutral.
What is wrong. The transmission shifts fine, the truck runs fine, but after 10 to 15 miles the transmission quits working.
View 1 Replies
Truck is 04 supercrew with 5.4 and 140,000 miles. I have the typical shutter when cruising 55 - 60 and just ease on the throttle to pass someone. I chalked that up to the torque converter unlocking, if I punch it instead of easing into it, it will not shutter. As of yesterday, it acts like the converter is going to full lock up almost immediately. It will bang when it shifts and rpm's drop to lock up range. A few times it has killed the engine when I shift into D. No codes at all, I removed the programmer and installed the stock tune, no change, unhooked battery, no change, fluid is good, and twice after leaving stop signs it worked perfect until the next stop. I believe that it is an electrical control problem.
View 9 Replies
Very strange problem for me especially since it's not my car, belongs to my sister. Only code that was set last month indicated the MAF so I cleaned it and the car ran fine. Started to hesitate up hills (steep uphill driveway) so I replaced the fuel filter yesterday and my sister said it drove just fine uphill. Now it stalls whenever put into drive, no codes set and none pending. It will idle in reverse but not in drive.
View 1 Replies
I have a buddy that has a 1998 f150 4x4 with 4.6l and 332836 km on it. It will go in to reverse but will not go in to drive at all. Is his transmission shot? Or is there anyway to test it to find out what the problem is.
View 4 Replies
I have a 2012 F-150 STX 4x4 with the 5.0 liter. I have noticed that when I put my truck in to reverse and sometimes drive I get a click sound. I jacked up the truck thinking it was the drive shaft that was loose but it wasn't... But I believe it is coming from the rear end. I found a video of the sound on youtube.
Check it out : 2013 F150 Rear End Click - YouTube .....
View 14 Replies
I have an 03 Escape that is very difficult to start after it rains, if I open the hood and let it dry out for a few days it starts fine, however if I put it in drive or reverse and press the gas it will not move... if I hold the brake while it is in gear and give it gas it does not rev up, however if I put it back in neutral or park it revs up. I normally cover the hood with a tarp to prevent this from happening however I was shutting the tarp in the door and a lot of water got in the floor board of the truck I sucked it all out, that night the radio started playing all on its own, I came out to the truck turned the radio off it stop went back in came back a while later and it was on again, so I pulled the fuse... but there are two buttons that stay lit on the radio the preset button 1 and 2 stay on all the time and I can not figure it out either. This is my beach truck I only use it for that purpose..however it is fall fishing time and I really want to go...
View 4 Replies
I have a 1988 FORD Ranger with the 2.9 liter engine with the four speed automatic overdrive transmission. Several days ago the transmission went out. The truck will not pull in reverse, overdrive, drive, second or first. Usually most vehicles will usually have at least the reverse, A first or second when the drive and overdrive stops working altogether. What the problem could be?
View 1 Replies
I am not the sharpest tool in the box. I was driving my 1979 f250 with a full load of fire wood going about 45mph when I shifted it from drive to reverse (I thought I was in 1st) the truck mad a loud whining sound then refused to go on. Now when I shift it in gear it feels like it wants to move and if I revved up high it will rock back and forth. A friend jacked up the rear end with the wheels off the ground the tiers spun in all gears including park and I was told they could stop the wheels by hand with the car in drive. He then took the cover off the rear end and found it to be low on fluid but no signs of damage. What I broke?
View 9 Replies
91 F-150 4x4 with AOD. OD,D,1st gear. The truck will idle fine, but when I put it into gear it seems like it is locked in in either drive or reverse. Its hard to stop at lights or stop signs and boggs the engine down and has no low end power. When in neutral it is fine. I have replaced the torque converter with a new one, no change. I replaced the valve body with a constant pressure body as well and still no change. Is there anything else that could keep the thing locked up? The smaller inside overdrive shaft looked good and slid in and out easily. Is there any kind of solenoid in the AOD that would cause this or if vacuum has any role in this problem...
View 1 Replies
