I have a 2001 m5r2 ford f-150 standard transmission. i have replaced the slave cyl., the entire clutch assy., the master cyl. pilot bearing. the trans. will engage all five gears plus reverse while truck is off but will not engage a gear while running. i have bled and bled and bled and still will not engage.
View 1 RepliesI recently installed a rebuilt engine on a 1997 Chev. s10, 5 speed. Decided to replace the clutch & pressure plate also. After bleeding the save cylinder several times, I could not get the transmissions to go into gear while the truck was running, although it would shift in all gears with truck engine off. I took transmission out again and replace the slave cylinder/throw out bearing. After bleeding 3 times I now have a full clutch, best ever, but still will not go into gear with engine running. It worked perfectly before replacing the engine.
View 5 RepliesSo clutch doesn't engage and compressor is not running. I have 12-13v at the low pressure switch and the same at the high. When I jump the low pressure I don't get any voltage at all at the plug that controls the relay for the clutch.
Where I'm confused is:
Is this a low pressure problem - gauge is reading 60psi on the accumulator
Or
Is this electrical somewhere?
1999 Ford Ranger 2.5L 5 speed transmission. I am a little confused I can not get the transmission to engage the clutch, I replaced the clutch 3 weeks ago, now I have no pressure in the pedal, I have bleed the system 5 attempts with clean solid flow of fluid. What else can I do to fix this or trouble shoot from here?
View 6 RepliesJust put the 6.0 back in the truck, engine working good now. Went to take it for a test drive and the transmission will not engage in any gear. I don't have any codes coming up on my scanner. Can not figure out why the transmission is not working from engine R&R.
- Fluid level is good
- Swapped wiring harness from my other truck and still nothing
2001 Accent 1.5 GL 165K miles.
The clutch doesn't engage until it's on the floor. I have to push real hard to allow the gear to engage. It then shifts... sometimes smoothly, sometimes it takes a hard push of the gear shifter, or it grinds until getting into gear.
I've changed the master cylinder twice in about 3 years but those times the pedal had no spring and just fell to the floor and stayed. Now, the pedal has spring (I push it to the floor and it springs back) so I assume the MC is ok. I even bled it with fresh fluid.
I'm not sure if the tranny fluid has ever been changed. Would changing the fluid fix this problem or does it sound like I need a new clutch? I'm guessing it needs a new clutch (or corresponding parts) since I've had two MC's go bad in a few years.
The pedal, even when it's shifting smoothly is pretty non-responsive and still engages a little mushy (comparing it to my 2012 Elantra 6sp).
I have a 2006 Mazda 6 with 104k on it. The clutch started sticking a couple weeks ago right where it would engage into gear, and I'd have to use my foot to pop it back up. It only happened here and there until finally, it stuck to the floor and became very difficult, if not impossible, to get out of gear. So everywhere I looked, it seemed that the slave cylinder was the culprit. I got a new one at AutoZone, replaced it yesterday, and the car ran great last night and this morning.
Then, this afternoon, in one 10 mile trip, it went back to the original problem. Stuck with every gear change, then stuck to the floor after I pushed it in and darn near wouldn't come out of gear. What in the world could be the problem?
1991 4x4 f250 idi w e4od w 3:55 ratio... The truck is slow to engage in reverse, about 5-10 sec. It also has a very hard shift 1-2. All other shift points are good. Drop down is good, and TC lock up happens at all the right points (feels like anyway).
I've had the truck for about 2 years now, replaced several sensors an harnesses and a full fluid change to solve other problems but this still remains.
Sometimes when I start it in the morning if I let it sit and idle for a few min it will engage reverse much quicker AND shifts way smoother and constant. Shifts smoothly thro all gears, holding a constant 1800-2000 rpms with no drop or lug. Or do I need a rebuild?
Replaced original clutch on Subaru Forester at approx. 130,000 miles because of slipping. Drove car for a few days and clutch would judder once warmed-up when trying to engage 1st gear. Took car back to repair shop, they said pressure plate was defective/set too stiff and replaced that. Whole car now shudders when trying to engage in 1st gear once the car has warmed-up and particularly on (even a slight) hill. What's not working correctly? Seen some discussion on throw-out bearings, master/slave cylinders and oil on clutch. Unsure.
View 5 RepliesThe problem started with a front seal leak a few months ago which I had no choice but to continue driving with because of low funds. I don't drive much so a couple of quarts of ATF was usually enough to get me out and about for what little driving I had to do. I know.. a front seal is cheap, but I'm partially disabled and unable to work on anything that is not under the hood.
I finally scraped up enough money to hire a friend to replace the seal, but he had a life crisis before completing the work, so I had to get another friend to reinstall the trany... still had the leak, but I could get around by adding ATF as before.
So we tried again... dropped everything and put another new seal on. This stopped the leak, but we got some grinding/squealing noises and could not get the trany to engage any gear.
From reading forum posts and other sources, we decided to replace the TC which we just completed this evening. We got some more of the grinding / squealing noise like before, except that it only occurred the first time we tried cranking the engine, the 2nd time we got no noises, but again no gears engaging.
What to check/replace next assuming there is something we can look at other than a total trany rebuild or replacement. I personally find it hard to believe we could have gone from a tolerably functional trany to scrap metal just replacing a seal and the TC. Its gotta be something simple we overlooked !!
1988 Acura Legend, 2.7L 6 cyl., 181,000 miles only do 6,500 miles a year to train station, parked inside, runs great. Last week parked out in hot sun, '90s, for 8 hours. At first, no problem. When did errand and returned to car, pushed clutch pedal and it would not return or allow gear to engage. "Jammed" into 1st, then could not shift, shifted slightly by pulling up on clutch pedal with my foot. Parked overnight, cool, next morning seemed to be fine and crept to mechanic. Mechanic road tested and found no problem and now seems to be working okay. Would parking in sun, high heat cause "clutch cylinder" to "seize" or "freeze"? Is there a "fix"? Also, increasingly hard to get parts for this car.
View 6 RepliesThey are about my F250. It is a 92 with 186000 miles. I love this truck.
After a long trip, maybe 1.5 hours, the truck will shudder while I let out the clutch in first gear. This only occurs in first, and it doesn't happen after the truck sits for a bit, just after driving.
I have an opportunity for a good deal on a F150. It is a 2001 with 181,000 miles for $4000. Is it worth updating for the new technology even if there is the same old high mileage issue?
I have an 05 F 250 super duty with the Triton in it. When I shift either into overdrive or reverse the transmission hesitates (does not go into either gear for about 5 to 10 seconds). After that it engages and it's fine. It does not appear to be slipping or acting up regardless of temperature or speed. Sometimes it will sort of engage and than bang into gear solid. I do not have any check engine lights. Not sure if the PCM has any codes. So I'm trying to figure out if I need to have a complete rebuild or if I have a valve / solenoid body problem Where do I start?
View 4 RepliesWell here it is I just put a new slave cylinder in my 02' F-150 and once we figured out all the little issues we were having we finally got the truck to fire up!!! Now my problem is that when the truck is running I can't get the truck into gear with the clutch pushed and it doesn't even grind. But when the truck is off it goes through the gears no problem what so ever. When we did the slave cylinder while we were in there we just replaced everything clutch, pressure plate, flywheel, rear seal, and pilot bearing. We figured that since all the shops were quoting me 800 and up for just doing the slave that since were in there we might as well do everything since nothing has ever been replaced yet. My question is why will the truck not let me shift into gears when running but no problem when off. Oh and yes the system was bled after doing the slave actually twice so far.
View 5 RepliesI have a 2001 F-150 4.2L 2WD LS with 102k miles. At 95k miles, the clutch slave cylinder started leaking fluid. So, I had my local garage replace it. And while they were at it, put in a new clutch. That is when the trouble started.
I cannot let the clutch out like I used too. When letting out the clutch from a dead stop,the rear end now shakes, shutters, and if it is really bad, the rear end starts bouncing. To minimize the shakes, I have to keep the engine below 1000rpm until the clutch/1<sup>st</sup> gear is fully engage. It is worst when there is a load on the truck like going uphill, or a sharp turn for a dead stop. After the truck gets rolling, I don’t notice the problem when shifting gears.
I have been babying it for 7k miles and it has not improved. What is wrong? Did I get a bad clutch job?
My clutch peddle made a slight "snap" sound last night and now it is very difficult to get the car to engage in a gear while sitting still, while moving it does ok, but not nearly as smooth as it should be. The other odd occurrence is that while the motor is running and the car is not moving, you can't shift any gears at all, but as soon as you cut the motor, all 5 gears and reverse are easily accessible. Why the sound at the peddle and the trouble in the gear shift mechanism? I am only an advanced beginner with car repair, but I think think this is really bad... 2007 Honda Accord Manual Transmission
View 8 RepliesI'll start this off with a few months ago, I went on a trip and along the way noticed that the car wouldn't get into gear. This happened for a few moments, and solved itself.
Fast forward to a few days ago:
So, my Golf MK4 AUTO 1.6L transmission doesn't want to shift into 4th, sometimes.
One and two are good, but sometimes I get quite a lag in between disengaging 2nd and getting 3rd also.
Furthermore, sometimes I get 4th 'semi' engaging, where the engine is revving too much to be fully in gear, but I get power to the wheels and accelerate (slowly).
I did a VAGCOM scan and got the old:
00652 - Gear Monitoring
27-10 - Implausible Signal - Intermittent
I also had a CEL on my dash, which I cleared with the VAGCOM. This removed the light, but of course the error still persists.
I've been reading around, and some people have said the issue is the TCM, but some people have had similar problems and a TCM replacement has not fixed this.
(Just btw, my TCM model is 01M927733LK).
And some people have had good results with solenoid replacements. So, I was thinking of doing a ATF flush, just because it was recommend on some posts, but won't necessarily fix the problem.
Contacted a garage to do this for me (never flushed automatic tranny before) and mentioned the VAGCOM codes, and he said this is a slip code.
So, now I'm not really sure what to do to fix it. Are the solenoids interchangeable? Am I able to switch two gears' solenoids to see if it moves the issue to another gear, proving its the solenoid?
The other day my transmission was driving fine, until I stopped to let someone out. When I tried to throw it back into gear, it wouldn't engage at all, just had a slight grind almost like the sound of a chain coming off a bike (so I pushed back in the clutch and parked it). I haven't been having any issues with it nor have I been driving it hard.
View 2 RepliesOur 2002 Elantra (automatic, 57000k) seems to have a blown transmission. A few days ago, it sounded like the car was "whining" and then it was having difficult time engaging next gear and eventually check engine came on and the car stalled. Firestone said it's a transmission problem.
We've had the car for less than 10 years so technically this should be covered under their powertrain warranty but I have a strong suspicion that the dealership will find a reason to not honor the warranty. It's still below 60k miles so we really didn't have to replace transmission oil.
I have a problem with automatic tiptronic transmission my golf MK4 TDI 1.9 2001, it dosent engage on 4th gear when i am driving, the codes that I received for this foults:
01316 - ABS CONTROL MODULE
49-10 No communication- Intermittent
00652 - Gear monitoring
27-10 - Implausible Signal - Intermittent
I have a 1999 Ford F350 5.4L 4x4. I had a check engine code on my truck a couple of months ago. The truck was running fine then. The light went away and I forgot about the issue. In the last week the truck began to run like crap; hesitation during hwy speeds. The truck is running with hesitation in 3rd, 4th, and 5th gear. In low gears the truck seems to run just fine. I have changed the EGR valve as well as the fuel filter. Check engine light is not on but the problem has not gotten any better.
View 3 Replies