Ford Transmission :: Loud Chirp - No Reverse / No Forward Gears On 5r55e
Jul 27, 2015
The other day I was leaving my house. I started the car and heard a quick, loud chirp. That was the only noise it made so I continued to leave. I rolled out of my driveway and proceeded to put it in drive and found myself rolling backwards. I tried every forward shift, kicked on the 4x4 and continued to roll backwards. I thought reverse worked but found that it wasn't engaging either. My question: is there anything I can look at before resorting to taking it to the tranny shop? I'm in school for automotive and am confident in my abilities to test solenoids and maybe even dropping the valve body to check that. Other than that, I lack the skill to pull the tranny myself and work on it.
View 3 Replies
Advertisement
I have a 98 expedition with a 4.2 liter 4x4 and what I believe to be a 4r70w transmission (u code on the door sticker)
The original transmission went at 105k miles and was replaced with a new factory ford transmission by a ford dealer 3.5 years ago. The new transmission only has 10k miles on it.
Now the new transmission only has reverse. reverse works like normal but no forward gears. the idle will change when i put if in gear, but will not move, acts like it is in N . There is no strange noises.
It's hard to believe a new trany is shot already, no towing, or off road use.
My question is : is there ANYTHING that can go bad that would cause this? The trany fluid is clean and clear bright red, and no burnt smell.
I want to check everything I can before calling a tow truck to have it looked at. I will have it repaired if needed, but I don't think I want to replace another tranny.
View 14 Replies
The truck is a 2002 f150 4x4 5.4l... I was driving down the free way last night in 2wd doing about 90kpm when there was a loud bang like a ran over something. Speedo went to zero and abs light came on. Pulled over and shut it down. Crawled underneath to check so damage and couldn't see anything. Stared it back up put it in drive and it just revs. No forward gears or reverse. Fluid level is good, bright pink. Dropped the transmission pan, pan is clean and magnet has next to nothing on it.
View 14 Replies
I recently bought a decent looking 1999 f250 4x4 5.4 auto. It has no forward gears and will only move in reverse. I topped off the fluids and have found no leaks so far the cooler lines are crusty but dry. I am gonna need to swap this thing out or do some more trouble shooting if there may be a non rebuild issue to solve.
View 4 Replies
I have a 95 F250 with 7.5 and E4OD. I was towing my Jeep and trailer out for the weekend a few months back (its been parked since) and heard some noise coming from the trailer. So at a stop light I put it in park with the engine running for a second, went to put it back into drive and it hasn't gone back into drive since. Reverse works perfectly. Fortunately I was able to back up onto the center divide, unload my Jeep and back the truck onto the trailer and tow home with my buddies Chevy. Anyways, its been dead since. Where I can start to look? None of the forward gears work at all.
View 13 Replies
My 1999 7.3l Disel 4x4 transmission quit on me the other day. No forward or reverse. Got towed to my regular repair shop, and they are treating the transmission as a black box and recommending total replacement. The diagnostics they performed were to make sure it was shifting, and that indeed it wasn't going forward or reverse. They drained the fluid and said "it's pitch black" and said it had to be completely replaced.
Fluid level was OK, and it wasn't hot. I was driving along, and merging onto the highway. It downshifted, shuddred, and nadda. Free rev. I coasted to the next exit and into a parking lot. Verified that it was shifting, checked Rev and all forwards. It wouldn't shift into 4W, and 1-2 also wouldn't move.
I'm trying to figure out what might have happened... and if it's worth trying to have the truck towed to a transmission shop and have them diagnose and rebuild, vs just getting a remanufactured transmission. None of the local wreckers have any used transmissions, and the cost between a reman and a used is pretty negligible...
Not sure what the symptoms points to for exact failure mode, be it the torque converter, pump, input shaft, etc... I've never had an automatic transmission apart before, but built plenty of motors and am a machinist by trade. My preference is to try and root cause the failure...
View 1 Replies
My '87 Chevy S-10 transmission slips like mad in forward gears and I can't go everywhere in reverse. The truck is gaaged in southern Virginia about 60 miles from my home and is used on some country property. The local transmission shop wants $1600 to rebuild the trans. He says he used sturdier parts than the replacement GM parts. I'd like to fix the truck because it comes in handy and was my dad's old mode of transportation around the Va. countryside, so it has sentimental value.
View 3 Replies
I'm having trouble with the automatic transmission in my 04' Elantra, it acted like the speed sensor was failing, but later the same day it lost all gears, forward and reverse. after turning the car off and sitting a while I started it back up and had gears again, but the trany is making noise. Fluid level is ok.
View 3 Replies
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 Replies
I drive a 1998 honda civic 5 speed manual transmission. The transmission is loud in all gears(including reverse) nearly all the time. It is not exactly a grinding sound, but that is as close as I can describe it. When taking off from a stop, sometimes it won't initially make the sound, but around 15-20 mph it will start to make the sound in 1st or 2nd gear. Once the sound starts, it won't go away. I can't link the time when it starts making the noise to any particular RPM.
I've hard the car for 5 years and 50,000 miles and it's made this noise the whole time I've had it. It is annoying more than anything (shifts smoothly, clutch not slipping). Someone who looked at my car shrugged his shoulders and said "when the clutch goes, put in a whole new transmission, that will probably fix it".
View 8 Replies
My low miles (under 50k) 1999 Ranger has a 5-speed manual transmission. One morning, I could not move it. The shift lever shifted, but the gears were locked. No forward, no reverse, and it wouldn't roll in neutral. Eventually, I popped the clutch, and, with a loud BANG! restored itself.
Background: I had rolled the car up tot the curbing in my driveway, so the wheels touched, then shut it off (in gear) and finally set the emergency brake. I'm guessing that this caught the gears in a way that caused the problem.
Yes, it's running just fine now. What happened?
View 5 Replies
Had tranny fluid and filter replaced a couple months ago. It's in a 35 foot motorhome (F53 chassis). The motorhome is within it's GCWR. Climbing a 6% grade at 3,500 rpm, little more than half throttle, like all the other climbs. 80 degrees out. Engine temp was on the letter "R" on the word "NORMAL". All of a sudden my engine redlines as if it popped into neutral. I let off, put it into neutral, and try "D" again. Nothing.
At this point it's uphill so it's naturally slowing down and I try "2". Nothing. Even slower and I try "1". Nothing. Pulling over blocking the right lane on a blind curve on a grade is scary. Had pylon cones out, waving traffic to warn them down a ways, etc.
No fluid on the ground, no slipping prior to this. I have reverse. I see no obvious linkage or electrical/wire issues underneath (from road debris, etc). It's at a shop but I want to know all I can so if they come back with something outrageous I can make a decision. I never pulled the stick, as I was coordinating traffic, highway patrol, a tow truck, etc.
View 6 Replies
I have a 1997 Mercury Mountaineer with a 4R70W trans behind a 5.0 liter. Vehicle sat for about 5 months. Went out to put it back on the road, and now the trans seems to be stuck in a forward gear no matter what the selector is in, park, reverse, neutral. Dropped the pan and replaced the filter and replaced what fluid was drained. no difference,.
View 3 Replies
I have a F150, 2nd 4.6, 122,000 miles. No forward gears. When put in drive, you can feel it trying to engage, but doesn't engage completely. Reverse is a solid engagement. Replaced filter and fluid, same issue.
View 12 Replies
2003 Explorer with a slipping transmission...codes are P0731, P0732, P0733... Just had a new solenoid pack installed last week when O/D light came on and truck was clunking into reverse. Now, after new pack was installed the forward gears are slipping all over the place!
View 5 Replies
I am looking at buying a 91 f250 4x4 with a 5.0 and an e4od. When I start the truck I can feel It roll forward A little bit. I can put the trans In od or nuetral and It will drive and shift normally thru all 4 gears, no slipping and no noise no vibration, It shifts and acts perfectly normal. 1st and 2nd work fine as well. When I put it in reverse It rolls forward slightly then drops Into reverse, it will not actually back up, you can rev the engine to stall speed but no higher. Sometimes in park If you rev the engine It will actually over come the parking pawl and roll forward.
Also when In park I can rev the engine to stall speed only. It only starts in p or n, and the reverse lights come on in R so Im assuming the mlps is adjusted properly and the manual protion is adjusted properly. I pulled codes and had 3 in total, ect shorted, egr flow insufficient, and 1 code for torque convertor clutch solenoid I believe It was 632. Im assuming the reving up to stall speed Is related to the tc code. The fluid level Is fine but is a little dark In color, I tried doing a search with no luck ..
View 5 Replies
I have a 1999 F-250 4X4 7.3 lit Diesel engine. My problem is my transmission will go into reverse great no problem but it won't go forward. I have no problem rebuilding the transmission if that's what it needs, I just want to make sure there isn't a electrical issue from the PCM first?
View 14 Replies
2006 f150 4x4 4R75E trans slipping in forward gears, reverse is ok. I dropped pan and it was clean. I dropped valve body and found OD servo shaft clip broken, the large snapring was I fine and in place. It allowed the inner shaft to float up and down. Would this cause my forward gears to slip or do I have a bigger problem?
View 14 Replies
The 91 bonneville stopped having forward gears but was drove back in reverse about 4 miles, reverse appears to work fine does this thing need new transmission or is there an easier fix...
View 7 Replies
A friend just bought a 99 Navigator, with what wikipedia says is the 4R100. Previous owner allegedly rebuilt the trans but used the old converter
It was apparently slipping a bit, or something, when he got it. Then on the way to my place so I can drive it and see what I think, it started making nasty grinding noises once he hit 4th gear. He got off the highway and made it to my place just fine.
Put it reverse to turn around in my driveway and it started the grinding noises again. Forward gears initially had some grinding as well after that, with no forward motion. Now there's no grinding, and the engine free revs in any forward/reverse gear
Fluid is full, still red, but smells nasty.
I don't suppose the three feed bolts above the valve body being loose would cause this? I imagine he's looking at a rebuild, which neither of us really want to do.
View 6 Replies
Early 2000 F250
Originally the truck would not go into any forward gear, but had reverse all day long. So I had a rebuild kit ordered (new bushings, seals, frictions, steels, a washer and flat bearing kit, a sprak kit, and the od piston)
After rebuilding it, taking my sweet time double checking everything, it will now go into forward gear but not reverse. So I dropped the pan. The small 3 bolt plate was torqued to spec. When I got to the third bolt in the smaller section of the valve body (upper valve body) I heard a click like maybe a valve returned to its place but I'm not sure. I removed the valve body and accumulator and all the valves were free and had tension. When I had it apart the first time one valve stuck for a split second but I never could get it to stick again.
Finding nothing there I uninstalled the tranny and took the barrel apart all the way down to the L/R piston and could not find anything wrong.
After the build and me running the truck for about 10-20 min there was metal on the magnet (part of the reason I took it all back apart) however I could not find anything worn or chewed up. Could have been the tc I prefilled with 2 quarts in stead of filling all the way.
When I initially rebuilt the 4r100 I took apart the pump to replace the bushing and seal but did not take apart the valves. I've heard the pump is directly related to reverse but I'm not sure. Could something gone wrong in the pump when I took it apart? How would I know? If I new all parts of the reverse system I could then test them.
View 14 Replies
