Ford Transmission :: How To Check Tranny Oil / Rear End And Clutch
Aug 11, 2013
I have an 86 f350 with a 4 speed manual transmission, I am trying to figure out how to check transmission oil and rear end, and clutch.
View 1 Replies
Aug 11, 2013
Advertisement
Ford Transmission :: E4OD Coast Clutch Resistance Check
Last weekend my 95 F350 developed an issue where it feels like something in the transmission is dragging in reverse and it moves forward in neutral. This happened suddenly. One minute it was working fine and the next it was acting up. I found some info that leads me to believe that it might be the coast clutch solenoid causing the problem. Today I tested the resistance of the coast clutch solenoid through the PCM connector. I used pin 55 and pin 37 to test it. The resistance is supposed to be between 20 and 30. I got 0. My meter read the same as putting the leads together.
Am I correct in thinking that I need a new solenoid pack or at least a coast clutch solenoid?
Passat (B5) :: New Clutch But Tranny Still Won't Shift
Ok my brother has a 99 passat he just put a new clutch in a few weeks ago and it still wont shift. I don't want to rip apart the trans and change the clutch again if that's not the problem...
View 1 RepliesGolf IV R32 :: Tranny Chatter - Still Exists After New Clutch And Flywheel?
Sounds actually quieted down and my mechanic is thinking its more the alternator pulley.
View 5 RepliesGolf/GTI VI :: 2010 - Chatter Coming From Clutch / Tranny
I have a 2010 5-speed Golf 2.5L. Around 2 months ago after coming back from vacation, i noticed that when shift from 1st to 2nd and from 2nd to 3rd, there is horrible chatter/vibration coming from i assume the clutch/tranny. its been getting progressively worse and its at a point where i can hear the spare change rattle in the cup holder. the car had been sitting for a month, and i sort of "broke it in again" when i got back from vacation, not revving over 3 on the first tank, not over 4 on the second. It does have 100k kms on it, solid mix of highway and city. Is this something easily fixable, i dont have a warranty so i'd have to go aftermarket. Not down to pay two arms and 3 legs for something that could put me back in this situation yet again. if its the clutch id just go aftermarket with something a lot better, or if its the tranny id put a 6 speed in it, really lacking on the highway i believe. Or maybe it's something else.
View 7 RepliesFord Transmission :: Reverse Go Out Completely On Tranny
I ran into an issue on my rebuild. I have a 1978 F-150 Ranger 302 V8 2WD Automatic. (Just to makes things easier) back to the point. I had the reverse go out completely on the tranny, and have not had any luck what so ever finding another I could buy.
View 5 RepliesFord Transmission :: When Go Into Drive Nothing Happens Like Tranny Is In Neutral?
I'm wondering what transmission fluid is the best to use for my 73' f100? Also wondering if changing the Fluid would stop the tranny from slipping. When i start her up reverse works great pops in every time quickly, but when i go into drive nothing happens like its in neutral?? after awhile of sitting and pressing on the gas a few times it pops in gear but very slowly and in stages.
View 1 RepliesGolf IV / Jetta IV :: Clutch Feeling Softer After Tranny Change
So long story short, last week I destroyed my first gear in the tranny. This weekend I did the complete swap and put a used o2j in. 5 speed. 2.0 motor.
Right after the swap, on the first startup I noticed the clutch felt softer. The grip is also a little less than it used to be.
Right before my transmission blew I upgraded from 15" alloys to 17" longbeaches with spacers all around- much heavier. It happened on my first drive with the new rims so I didn't get to feel the car much.
I reused my current slave cylinder. Did not disconnect it from the line while swapping. I did however notice my slave boot had a small little dent in it (super small) but no tears or anything. Also, reinstalling it i pushed it in and compressed the boot and secured it with the bolts - I hope I did this right.
I redid my rear brakes about a month ago, did not disconnect brake lines or bleed the system.
I have already driven about 50km on the new tranny. Today I am getting the tranny service (flush) done because I didn't have the sockets to check it after install. I'm going to ask the mechanic if he might know anything. The brakes also feel a touch less but I'm not sure if this is cause of the 17" wheels.. does the system just need to be bled?
All gears go in smooth - clutch in.
All gears go in smooth with car off.
No grinding of gears when switching or driving.
No reverse grind.
No slipping in any gears.
Just a soft pedal and feels like softer bite. I did the tranny swap in a rush, did not replace fork, TOB or anything. They should all be fine, I'm thinking it's just air but need confirmation. I just want this car to last another year or so..
Ford Super Duty (1999-2016) :: 2002 - How To Check Cooling Pump On Tranny
I have the 6 speed (ZF) i know there is a cooling pump on this tranny. Is there a way that you can check the pump to see if it is working???? If not will it set a code??
02 7.3 CC
Ford Transmission :: C6 Transmission Keeps Burning Up Reverse High Clutch Plates?
I have rebuilt my transmission but it keeps burning up reverse high clutch plates. It has burned up two sets so far. I am thinking that it might be something stuck in the valve body.
View 4 RepliesGTI 337/20th Anniversary :: Chatter Coming From Tranny But Stops Once Clutch Pressed When Car Is Idling
I have an 04 Gli with 85000 miles on it. I just had the clutch done with a conversion from a dual mass to a single. When the car is idling there is some chatter coming from the tranny but it stops once i press the clutch.
View 3 RepliesFord Transmission :: 4R70W Tranny Making Shuddering Sound While Downshifting?
I have a 2002 F150 Super crew with a 5.4 and a 4R70W tranny. The issue I am experiencing is when the truck is driven where the tranny has shifted through all it's gears and cruising at say 55 mph, when depressing the accelerator pedal it either downshifts of something unlocks making a shuddering sound which sounds like when you run over rumble strips on the side of the road. The shuddering only happens for maybe a second at the most. If I am on the accelerator pedal when it up shifts or locks back up it makes the shuddering sound again. The harder the unlocking / locking or downshifting / up shifting happens the harder and longer the shuddering is.
This shuddering happens at the very last transmission function which happens in the transmission during it's normal operation. Other tan this issue the tranny shifts and operates excellent.
Ford Transmission :: 1978 F250 - Tranny Quit Working Suddenly?
I have a '78 F250 4x4 with the 400 engine and C6 automatic tranny in it. All of the sudden, it won't shift as I'm driving. It will go into reverse, drive, 2, 3, when I'm shifting, stays in the same gear all the time while I'm driving.
I was looking around and I found a hose that I think goes from the top of the tranny to...nothing. A friend said it's a vacuum hose that should go from the shift modulator to the carb. Well, I can't figure out where it should connect to the carburetor. There is a hose towards the front of the carb that was cut off and is plugged with a bolt, but that's been like that since I bought the truck 3 years ago. So if that's where the hose SHOULD go, then something else must have caused the tranny to give up on me.
Tranny has been acting fine until now. And I'm sure that hose should go SOMEWHERE!
Ford - Aviator :: 2005 - Tranny Slipping / OD Light Blinking And Check Trans Message On Display
O/D light was blinking and "check trans" message was on display. I brought in for service and they changed trans fluid & filter. I have to take back to service center because now tranny is slipping. I would like to have some information before going back. It was not doing this before service. It is OK on highway for most part, happens more when starting out. Also has shut off a few times while sitting at a light. It didn't do any of this before service. What would cause this? Could it be the wrong fluid or not enough added?
View 1 RepliesFord Transmission :: 1971 F250 - NP435 4th Gear Grinding After Tranny Replacement?
I have a 71 F250 4x4 with the 435 and recently had the tranny out to replace the output shaft i believe its called, and other than the shaft it seemed all was well. Shortly thereafter it became impossible to shift it into 4th gear without it grinding. I am able to minimize it by double clutching and keeping the rpms right, but the grind is unavoidable and its only 4th gear, all others shift fine. I was hoping there was a way to adjust the clutch but if not am i going to have to pull it back out and look at the fork and gears? But like i said, we just had it out and the fork and gears seemed fine.
View 5 RepliesFord Super Duty (1999-2016) :: Check Engine Light Blinking And Tranny Just Stopped Working In All Gears
I have a 2006 f250 5.4 4wd with 5r110w trans. Check engine light was blinking and then one day the tranny just stopped working in all gears. Engine code p0751 came up, shift solenoid "A". Changed it, code went away and still no gears. Checked pump pressure, good in all gears, all I can think of now is TCM....
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Oil Leak From Rear Lobe At Pan - Tranny Out Next?
So last year I pulled the motor and put a new pan on. Since then the oil has leaked from the rear lobe at the back of the pan. No oil leaks up top of engine. So I pulled the tranny and am going to put in a rear main. I also see a plate that bolts on the back of the motor and the bottom glues to the pan. I am concerned I did not glue the pan well enough in the lobe as only about 1.5 inches of the lobe has a small amount of grey rtv sticking out. How do I remove the aluminum mount on back of motor that the tranny bolts to? What seals the plate? Oring? Gasket?
View 2 RepliesTouareg :: Codes For The Tranny And Rear Diff?
I am looking for the codes for the tranny and rear diff on my 04. I know the engine is a AXQ but I can't figure out what the 6sp Auto and locking rear diff is. Where on the vehicle I might find these?
View 3 Replies4160 - Transmission :: 2008 - Getting Error P0700 Code Even After Replacement Of Tranny?
4l60. Tranny 08 xpress. I'm getting p0700 code. 2 weeks after first getting code the tranny went out. Replaced tranny but still getting the same code. Should I b worried and how can I fix it.
View 3 RepliesToyota - Camry :: Tranny Fluid Is Black And Smell Burnt / Transmission Is Slipping
My car is a Toyota Camry 2003, automatic transmission. I don't know if the previous owner ever change the transmission fluid, but my car has 100k miles already. Today, I took the transmission fluid dipstick out, it look black and smell burnt, but I don't see any metal. I don't know how to take out the pan and check for metallic pieces, is there any auto shop that would do it for free?When I accelerate to 40mph from a complete stop, the RPM goes up the 3000 and then quickly drop to 2000, then gradually drop to 1300. My car speed up really slowly even when I keep holding the gas pedal down with my feet. Is my transmission slipping? Sometimes when I start my car or when I change gear, my car jerk a little. I'm afraid it too bad already and my transmission is depending on the broken metal pieces, so I don't know if I should flush it? Will changing the transmission fluid fix the problem?
View 8 RepliesFord Transmission :: 2000 4X4 - Clutch Won't Disengage
2000 ranger, 4.0L 5spd 4x4
Recently my buddy's 2000 ranger's clutch stopped working, it wouldnt disengage. I checked the reservoir and it was empty, checked below and between the bellhousing and engine was soaked. I filled the reservoir up and attempted to bleed the system with my vacuum bleeder and it barely got any fluid out. Ordered a new slave cyl and just put it in today. You could see how wet the old one was when I took it out.
So today when I finished installing everything, I filled the reservoir and bled the system, lots of fluid coming through, everything seemed good, however the clutch still feels extremely light, and won't disengage. I looked at it through the inspection cover and there is maybe a 1/4" of movement total. I don't get why this thing is not working! How can you tell is the clutch master cylinder is bad?