Ford Transmission :: Hard Shift And Clunk When Shifting To Reverse
Dec 19, 2012
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 Replies
Advertisement
I'm having problems with my 6r140 in my 2011, the truck is an early build around 8/2010 I believe.
After cold soak when shifting into reverse after allowing engine to warm a bit the transmission almost always slams hard into reverse.
After that shifting from 1-3 is awful, the transmission will try to go into 3rd but downshift to 1st then fail to go back into 3rd multiple times. This situation is extremely dangerous when trying to pull into traffic.
Oh and once the transmission gets into 3rd it will skip 4th and go right into 5th. There is only 94k miles on this transmission/truck.
I just bought this truck about a month ago, does this sound like an issue with the solenoids in the valve body?
I'm very mechanically inclined and can swap them if need be but now we're talking few hundred in solenoids and then getting the trucks pcm flashed right?
Also fluid has been changed and I used mercon lv.
View 14 Replies
Noticed that the transmission is cold (ie. sits overnight) it is hard, sometimes impossible, to shift into reverse. Specs on my gti: 14k miles, pretty much stock, manual trans...
View 1 Replies
I have a 97 jetta trek that is having problems. Grinding noises from transfer , no reverse, hard to shift, loud winding noise. I think it's may be the trough out baring thing from what I'm reading.
View 6 Replies
I have a 93 ford escort which makes a clunking noise if I shift into reverse without letting the car warm up and idle down. It sounds as if the noise is coming from the front passenger side wheel well. The sound does not occur when shifting into reverse if the car is allowed to warm up and idle down to 1100 rpm. What's up?
View 6 Replies
2014. Noticed the feel and sometimes clunk when shifting to 4 high? My house sits up a hill and this time of year, routinely have to use 4X4 to get up. There is a little more noise and vibration than im use to. Usually shift coming down a semi flat dirt/ice road at low speeds, typically about 10mph. Going in for first oil change soon and was gonna ask them to check it out for peace of mind.
View 6 Replies
This is on my 7.3PSD. I've observed that the 1-2 gear shift drops about 1,000 RPMs and takes a good half second or longer to do so when given a lot of accelerator pedal input. And then the 2-3 shift is a very quick and harsh shift.
If I am accelerating gently the 2-3 shift is as unnoticeable as the 1-2 shift is quick. Is the slow 1-2 shift causing the trans to protect itself and affecting the 2-3 shift? And if so, what do I do to resolve all of this? I changed the trans fluid a week ago and there is no change.
View 2 Replies
2001 F-350 w/powerstroke. Tranny is the automatic w/overdrive. right at 170K miles and it has not been serviced since I've owned it (about 10 years).
Lately it is jerking when shifting, especially noticeable when I'm pulling my 5er (10K lbs). Almost a "clunk". No warning lights or OD flashing. I live at 6000 feet and play at over 9K so mountain driving is routine. Fluid is up to right spot on the dip-stick.
View 1 Replies
I continuously read that people with 6.2 F250s averaging 13 mpg or so in a combination city/highway driving. This 2014 4x4 barely has enough power to move itself (honestly, I'd rather have my Ram 1500 back) and barely gets 10mpg. Basically have to give it about half-pedal to even get up to freeway speed and floor it if i want to pass anything. Is it just that much of a POS or does this not sound right? Other than a massive "clunk" sound when shifting from reverse to drive or vice versa, no indication of any problems.
View 14 Replies
I just had the motor torque and strut mount fixed and was told that I have an exhaust leak flex pipe. My problem is I'm still getting a clunk when shifting into reverse doesn't happen all the time but it is concerning plan to have flexpipe fixed in the near future. will that take care of the clunking sound or is it something else? don't have a lot of cash to work with right now.
View 1 Replies
This truck has been giving me tranny problems for a while now. About a year ago, stopped in traffic in neutral, I attempted to shift into 1st but it wouldn't go into gear, not reverse, not any gear. Eventually after a minute or so of trying it reluctantly went into 1st. About 6 months ago I started the truck after being parked and again it wouldn't get into gear. Shut it off, tried to get it into gear, nothing. Checked the hydraulic fluid reservoir for the clutch and it looked a little low so added a bit and after that it shifted into gear (maybe coincidentally). Now about a month ago, it again wouldn't shift into gear after being started. I checked the reservoir again, looked fine this time. Shut the car off, attempted to shift and this time shifted with ease
Something that I've noticed in the past year is that sometimes now when I shut the engine off it doesn't run down smoothly; kind of slows then clunks to a stop. Didn't used to do that.
View 2 Replies
Could my brake issue be related to my transmission problem? Neither are constant. Brake problem= sometimes the brake pedal feels hard, like there's no power brakes (I drove a car once. ..looong time ago. .. that had no power brakes or steering) but it will kick in after a short distance. Transmission prob= seemingly unrelated, is a problem shifting from 1st to 2nd gear. This has happened maybe a 1/2 dozen times, the first time and mostly when in heavy commute traffic and when going between 1st and 2nd gear because of the slow commute speed, but also at other times when not in lengthy slow commutes. When it doesn't shift, the odometer doesn't work (shows only dashes) and an engine light comes on (the sprocket/gear looking one). Usually the transmission will eventually shift and the light goes off.
I read that the brake problem might be a vacuum hose problem? Something about a booster? Is this dangerous? or is it like having a car w/ no power brakes? Going to have my transmission looked at this week. Read on another site about dropping valve seats on this year car. If there's a major transmission problem, I'm wondering if it's worth fixing? I changed, timing belt, water pump, front and rears brakes, tires. 143,000 miles.
View 1 Replies
Sometimes when putting the vehicle into first it's almost impossible to get it to go into gear. Sometimes it's super smooth. Also when putting into reverse we hear a loud clunk. That one is most of the time but sometimes it goes in smooth. I was doing some looking around at the pedals because I think I am going to have to replace my master cylinder and noticed that on the inside of the vehicle where the clutch master cylinder comes into the vehicle it's leaking black fluid. Does that automatically mean my clutch master cylinder needs to be changed? Could this be the cause of it being difficult to shift because the clutch isn't fully disengaging?
View 11 Replies
I bought a 2005 Accent with 150k one year ago and 3 months ago got AT fluid and filter changed. Color was very dark my mechanic friend said.
I checked the fluid and after just 3 months light driving, noticed it smelled burnt and so just changed it again yesterday and it was very dark.
Another piece of info is that previously when got the fluid changed 3 months ago the level registered way above high when car was off but then then normal when running in N. Same thing is happening now. My knowledgeable mechanic friend just told me to keep my eye on it.
There are no shifting issues, except for just light clunk when shifting into Reverse, but other than that it's great.
I just want to know what problems might be going on to burn the fluid so fast and have strange level readings when car is off but okay when on. I read some stuff about solenoids but because shifting is great should I even consider that?
View 2 Replies
I have a 1999 chevy silverado 5.3 4wd w/ tow package. I bough it with 30,000 mi. It has always had a hard shifting/clunk after long drives or sometimes short ones that involve a lot of elevation. Oddly, if I stop and shut the car off for a minute or two the hard shifting stops, but eventually starts again. The truck now has 160,000...still with the shifting issue. What is this and with this many miles is it serious?
View 4 Replies
I have a 1999 chevy malibu with a 2005 chevy impala motor in it. Recently I put my car into reverse and it made a hard clunk and went into reverse. Later on that day I tried to go into reverse and it will not reverse. I had to have 3 people push my car back in neutral. However, in neutral I am able to press on the gas and drive forward... This is an automatic transmission. Am I just screwed and need a brand new transmission?
View 12 Replies
So a friend of mine has a 01 Passat 1.8 T (Automatic). He is having some reverse issues. It shifts into reverse with a hard clunk then the second you touch the gas it clunks into neutral. The odd part is if you put it in reverse and stay off the gas it will idle back in reverse... But the second you touch the gas nothing. I'm finding it hard to believe the transmission is gone because every other gear is beyond smooth (I mean like brand new car smooth).
View 4 Replies
My 2005 Impala will have from time to time a hard shift where there is a big clunk_usually 1st gear. I had it at a transmission shop last year and they could not find anything wrong. What is going on.
View 3 Replies
I have a 2005 Ford Focus Man Trans, and am having issues getting it into first gear and into reverse. This happens most often when the car is cold. I am kind of wondering what it may mean before I take it in to have the issue fixed. It has 65 thou miles on it and I would think that I don't need a new trans already?
View 8 Replies
bought the truck about 3 weeks ago and still having problems with the transmission. Replaced the VSS and it didn't work. My problems are it shifting hard from 1st to 2nd, it feels like it falls out of gear ( i can floor it and the speedometer creeps up then shifts hard.) Now i read having the 3rd brake light out is a problem with the trans too, my 3rd brake light is out along with the interior dome light ( doesn't go on when doors open) i plan to replace the TRS on the tranny tmw is there anything else i can do? how do i solve the brake light problem?
View 14 Replies
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
View 14 Replies
