Trying to fix my 97' F-250 5.8, e4od. The e4od won't shift out of first gear half the time. It is fine when I manually select 1 or 2 when the problem happens, no check engine though. The fluid looks great and doesn't have an odor. Here is a video of it failing to shift...
YouTube....
My son was driving my F250 (big mistake) when as he says he noticed it was leaking transmission fluid. As he was driving it he noticed fluid coming out then it just stopped working.(motor was running but transmission would not pull in any gear) We towed the truck home and let it sit for about a week. Now it will start but when I try to shift it into gear it will run through the gears but there is no action. It will not engage into any gears.
View 6 RepliesI have seen a few threads about E4OD's and there valve issues just want to narrow down to a valve issue or if it needs a rebuild. I can shift threw all gears i just have lag going into 3rd. also when putting it in reverse it takes about 5 seconds to finally drop into reverse. This is also accompanied with P0782 2-3 shift malfunction.
View 6 RepliesThis has been a problem since I got the truck. It's a 1996 F150 5.8 4x4. It's got about 140,800 miles on it; had about 139,000 when I picked it up. Not sure if the trans has been rebuilt or not. I'm the 3rd Owner. It doesn't matter what temperature it is outside or how far my foot is down on the pedal... Just about every 1-2 shift is accompanied by a little kick/jolt. Going slow..(coasting, about 15mph) and it shifts into 2nd, usually the jolt is harder than hell!
Same goes for when I'm going about 25mph and I put the pedal to the floor It downshifts then comes back up to 2nd gear and wow. It jolts, shakes and shudders. Sometimes (rarely) I don't feel anything when it shifts. But it ONLY and always happens 1-2. not 2-1 either. Furthermore, when I go to put my truck into Reverse it kind of slams into it, with a clunk noise. All fluids have been changed recently and I also put "Lucas Oil Transmission Fix" in it and that didn't seem to change anything. What is going on internally?
I have a 1997 f250hd that shifts into 4th at about 25mph and lugs the motor down, then shift back to 3rd (maybe its 2nd and 3rd). It will keep shifting back and forth until you get up to speed, or if i'm in town i will put it in second.
No codes but the tranny fluid is dirty. I changed the filter the other day but didn't have time to flush it as it was getting dark and the line into the tranny was pretty rusted and starting to strip. Also there was no burnt smell. I'm planning on taking it in to have it flushed this week.
I bought a '93 F150 4x4 this past Sunday. It has the 5.8 and E4OD. Yesterday when I started it up and drove to the tire shop for some wheel balancing, it shifted VERY hard with each shift, so hard that it concerned me. I know very little about transmissions in general, and this one specifically, aside from it being electronically controlled.
This afternoon, I drove it again and it seemed to be shifting more "normally" without shifting anywhere nearly as hard as it did yesterday. What I should check first? I bought a filter kit and will change the filter/fluid (including torque converter) as soon as I'm able.
I have a 94 E350 with the 460 and the E4OD trans. that has only 30K on it.
Last weekend I took it on a 250 mile trip (one way) and it ran beautiful until the final steep hill to our vacation house. It started vibrating when it went to down shift and wouldn't pick up any speed, the OD off light was blinking. When I pushed the OD button and it cleared right up. Ran beautiful until I tried to climb that same hill again (same thing happened). It showed the same symptom when I tried to back up a steep driveway during the same trip.
Now it no longer does the vibrating but now has harsh/firm up shifts. Downshifts are smooth though, but shifting into reverse and drive are bit clunky too.
The codes I pulled were KOEO 212 and 668. After I erased the codes the 668 didn't come back. But I did change the MLPS to the new updated one from Ford and its still doing it.
I also found the 40amp mega fuse under the hood was blown too, related? Could a 1/2 qt over filled trans. cause this now too? In NH I added some fluid thinking it was low because I could not get a clear reading on the dipstick but I think the level was up there.
The trans in my motor home has made a growling or slight grinding metallic noise after it shifts into 3rd gear. It only does it for maybe 3 seconds and it doesn't seem to affect the operation. Only way I can describe it is that it grinds, and shudders then goes away. I have towed my race car all this year and it has not caused any issues at all. I am planning on driving out west next year and would like to figure out what the deal is before I hit the road. Also if a rebuild was in order what improvements can be made during a rebuild?
View 1 RepliesO.K. first of all I had an issue with the Odometer pointer being jumpy. Sometimes it wouldn't move. Now I replaced the input sensor at first and did not fix the problem. I replaced the output sensor and fixed it. "BUT", Now, I have a problem with the transmission shifting. I get an engine light while driving and the 2nd gear seems to take its time shifting and when it does it make the left side drive shaft kick in hard and spends my wheel to a screeching effect. Plus a thump on the transmission. I rechecked the sensor for connection and reinstalled. Drove the car still have the same issue?
View 2 RepliesI have a 2000 F150 5.4L with 157k miles on it. I think it has the 4r70w trans. The transmission has started holding 2nd gear too long before shifting into third. Throttle position doesn't matter, it does it even under light throttle. I do not have a check engine light. I have owned the truck since new and the trans fluid has been changed 3 or 4 times. The fluid looks pretty good now, not burnt or anything. The truck has been sitting in the garage a lot over the past 2 years, I drive it at least once a month and have put maybe 2000 miles on it this year. It shifts fine through the other gears, just 2-3 has an issue. Truck has the towing package.
View 6 RepliesAuto tranny takes a half second to go into gear. It doesn't slip just slight hesitation going into gear. This rig has 173000 miles on it and I don't know its maintenance history and don't want to stick much money in it.
View 3 RepliesMy 2006 Elantra (54,000 miles) shifts really, really hard when it's not cold and passes through the 35 mph range -- hard enough to make you glad you've got your seatbelt on. I've taken it to my regular mechanic and now it's in an automatic transmission shop.
My mechanic changed the fluid (twice), and took it through a "learning sequence". The fluid didn't look that bad and he reported that there were no codes to work with. He thinks I'm going to have to get a new transmission.
The AT shop has confirmed that there are no codes to work with and that the problem begins at 143 degrees. They tell me that the transmission is shifting into a higher gear without releasing the lower gear. They tried replacing a couple of solenoids, but that yielded no change in behavior. Now, they're telling me they "think" I need a new computer. I'm just afraid the trial & error approach is going to cost me a boat-load.
My tranny slips in drive and od when it is warmed up.It's fine for a few miles when it is cold.Did a quick search and it seems like it might be a bad mlps.
My question is, Will a bad mlps act up all the time or just when it's warmed up? Will a mlps and connector from a 91 tranny work on a 95 tranny? Don't really want to throw money at it if it will need a rebuild.
Have a 2000 expedition with 84,000 miles. Tranny seems to shift hard from first to second gear. Its been 24,000 miles since my last dealer tranny service. Thinking of getting a new service now before the recommended 30,000 manual recommendation. Whats happening?
View 6 RepliesMy 94 F150 has been actingup lately with the 4r70 transmission not shifting into 3rd gear or above. I replaced the MLPS sensor and re pinned the plug as per the instructions with the switch.The old sensor had the plug on the side, same type of plug, but wires indifferent spots. Truck wouldn't start like that, so repinned to match the instructions. I couldn't get the neutral mark to 100% line up as there is not enough adjustment, but it is very close.
The old plug had
32-298-140-33
57-199-359-463
I switched it to
57-359-199-463
33-140-298-32
Then tried
463-359-199-57
33-140-298-32
Truck still won't shift to 3rd, overdrive off button doesn't light up and itwon't start in neutral. I tested the ground at the connector and it lights up atest light connected to the pos bat cable with no issues.
Back up lights won't work, but flicker as going from R to N, so I suspect that is due to the fact I couldn't get the marks to line up 100%, but i'm not worried about that now.
I have a 1986 Ford Bronco straight six 300 4 speed manual NP 435
She grinded a bit when shifting from a stand still but nothing terrible for an old rig but leaked oil bad from the rear main seal so I took out the tranny/t case to put in new clutch, throw out bearing, pilot bearing, and rear main seal. When I put it all back together shifting into 1st would grind like CRAZY. So would reverse but not near as bad. So I took it all back apart inspected everything even torqued the clutch to specification. Put it back together and same result. So I replaced the slave/master cylinder thinking the clutch wasn't pushing enough bench bled it and still no luck.
I have a '97 F150 4x4 with the 5.4L engine and automatic transmission. The tranny's been slipping on and off for a couple of years. It started when it was hot outside, I had been driving a long ways, and I was trompin' on the gas to pass someone. Still, the slips were rare. As it got worse during the hot summer months, I just minimized my long-distance travels.
I recently took it to a transmission mechanic. Like some of the feedback to posts in here, he felt it was a problem with the engine - because we had a bad EGR valve signal on the computer. (We still flushed the fluid. I later replaced the EGR and the DPFE. Another mechanic went through everything, replaced some valves that had something to do with the EGR, and feels the engine is 100% (and it runs very, very smooth). For those that will bring it up - I have replaced all of the coils (though it's been a few years). Having actually replaced some numerous times over the years, I can feel when one is bad (of course, the 'check engine' light as well). Lastly, we've replaced all bulbs in the dash so they are all working as well. Also, the transmission is not leaking. The computer system is giving us no errors/throwing codes.
After a couple of weeks, I happened to drive the truck a long distance one day and it started slipping. It got bad enough that it was slipping every time going from first to second gear. It would usually engage as I took my foot off the gas. Since then, because I haven't driven long distances, I have not had a problem.
The transmission mechanic thinks it's still an engine issue. He also mentioned a mechanical/electrical switch system on the side of the transmission (?). Give me a list of things to look at.
I just had a 97 Ford Ranger with a 3 speed overdrive transmission in my garage that we replaced the transmission because it was not shifting down into first gear, not even manually!. The new transmission is doing the exact same thing as the original.
View 5 RepliesMy 1992 F-250 7.3 4X4 has a very intermittent issue with the E40D. Rarely, usually after a lot of around town driving (I don't know if that has any direct correlation), I will get a rough shift from 1-2. It will kind of bang into gear and make the whole truck shudder.
On one of it's episodes, it also did it in 2-3, however that only happened once and I haven't been able to make it do that again. I'm worried that it's something that I should address, if I can do so without just rebuilding the whole transmission. It doesn't slip and shifts fine most of the time, other than the occasional 1-2 issue.
To cut this short, does this sound like a 1-2 accumulator issue? Maybe just old truck syndrome? I feel like this is a dumb as hell question, but isn't it a bad idea to install a shift kit in an E40D with 126K miles on it?
My 95 psd recently started shuddering on takeoff... Pretty sure its the torque converter. It has a full ATS tranny with 5 star t/c and all the goodies installed by the previous owner (warranty not transferable). Its only got about 25k on the trans but they have been far from easy miles.
Symptoms: If I hold the brake and keep the truck stopped while holding the throttle its totally smooth, not until the truck starts moving that the shudder begins. It shudders worse the more power i put to it. Does it in first gear and second gear takeoffs. Goes away at about 10 mph or once the speed catches up with the rpm.
I have a M5OD that I replaced the clutch in in my '99 150 4wd in December . Manual Tranny. Now when taking off in 1st gear the transmission seems to be sliding or shifting backwards, but only in first gear. Got under my truck and looked, can't find any identifying marks to where it might be moving or what is causing this. All frame mounts are tight and the bell housing is flush with the motor. Yes, i did do the clutch change myself in shop class.
View 1 Replies