Ford Transmission :: Constant Clunk / Binding Noise From Front Drive Shaft Area
Dec 7, 2014
I bought this 2010 f150 from the company I work for, front diff was shot, front drive shaft was in the bed, that's all I knew about the truck so I bought a complete front diff from a used place, it only has 58000km on it, good diff... So I installed the diff and the old front drive shaft, which doesn't seem to be in the best condition, now when 4 wheel drive is engaged I'm getting a constant clunk/binding noise from the front driveshaft area. Where to start looking.
View 2 Replies
Advertisement
Bought a used 1997 Lariat Supercab 5.4L last week. It was missing its front drive shaft so I want to install one.
I just ordered a used front drive shaft online but I now need the bolts that connect everything together. New drive shaft has all the flanges, etc.
What is the pitch/length of these bolts? The part number for the bolts is N800594-S100 (AB-308-D). I believe there would be 8 of them, 4 on each side.
I thought it might be easier and cheaper to just buy bolts from an aftermarket supplier instead of OEM from Ford.
View 2 Replies
I just bought a 5speed manual 2004 ford ranger 4x4 and when shifting usually upshiffter 1-2-3 I get a mi8ld clunk when I looked underneath I grabbed and can move the from drive shaft clockwise about 1/4 inch is this normal and if not how do I fix this?
View 3 Replies
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 Replies
I have a 2014 4WD Super Duty. It has a squeak that is coming from the drive shaft area. I had someone listen to it as I drove slowly next to them. It is a repetitive: squeak squeak squeak squeak squeak. Not loud. The frequency increases as speed increases. I could believe it may be a U joint based on the frequency, but seems hard to believe with a new truck. I heard this sound when I first got it, but the sound was so slight that I thought it was just some sound associated with a newer engine. But now it is becoming a bit louder.
View 4 Replies
I got a few clunk noise from front left tire area. I think it happens when I turn my steering wheel to left almost max.
And then, turning back to straight(to right). then, "Clunk"!
Today I got the clunk when I made U-turn on a street. A month ago, I heard it when I parked with fully turned front tires.
View 6 Replies
I've got a 2005 Avalanche (basically, a Silverado) which has suddenly developed a possible illness. Whenever I start the truck and begin moving (forward or reverse), I hear one (and only one) loud squeak that seems to be coming from the general area of the torque converter or drive shaft (but who knows exactly). The squeak doesn't happen immediately upon moving but always happens within the first 20-30 feet of movement and then no more. If I put the truck in park, re-engage the automatic transmission and start moving, I cannot recreate the sound.
However, if I turn off the engine altogether, restart the truck and begin moving, it happens again exactly as before. It happens every time the vehicle has been restarted, regardless of whether the engine is hot or cold. Once it's happened, I can drive hundreds of miles and it won't happen again until I turn off the engine and restart it. Further, I've determined recently that if I start the truck on a hill and let it roll while in neutral and without a foot on the brake, the squeak still happens. Therefore, it's not dependent upon the transmission being in gear or the brakes being applied!
View 5 Replies
I drive a 2008 Cobalt SS turbo. its been a good car and I haven't had any major problems with it aside from the small stuff.
Well for the past few months I've noticed that, whenever i drive in heavy rain or in snow etc I will get a loud Growling/whining noise from the transmission area. Now it will do it while in Neutral, 1st etc and when stopped it will go away. If I stop the car for a few moments, the noise goes away until I hit another puddle and then it comes back again.
I also feel a "knocking" in the shifter and I've noticed its vibrated really badly for awhile now.
the caveat to this is it ONLY does it when its wet outside. I've taken it to GM a few times, and even showed the service manager the issues when it was raining out and he said everything was fine. The car never did it when I first purchased it.
I should include that there are some aftermarket modifications on the car. Catless downpipe, new intercooler, lowering springs. stock exhaust and stock turbo.
View 1 Replies
I am wanting to remove my front drive shaft from my 2004 Aviator for a couple of month's while I save money to have my transfer case replaced. Are there any safety concerns with this? just need a couple of month's to get the money together....
View 5 Replies
I am doing some work on the truck and need to get the front drive shaft to drop down, I have the four bolts out but I can not get it to move. What am I not doing?
View 3 Replies
My t case will engage in 4 high and 4 low. so i know the switch and motor works because it go all the way to 4 low and i can feel the lower gears. BUT the front drive shaft is not turning because i know that the front diff is engaging just fine cus one I just fixed it and because when i put it in 4x4 the front drive shaft is locked in but when i take it out the drive shaft moves freely when i turn it by hand. But when I test it in gravel or mud the front wheels still ain't turning. So its gota be the t case. But what are the part that may be broken in the t case and if I can fix it wile its still on the truck.
View 4 Replies
After 11 VWs, I finally have one that I would love to drive over a cliff. My 2015 Golf TSI Sport is a miserable car for me. I have had it back to the dealer four times for the infamous "shimmy" and shift problem with the automatic transmission. It has the standard automatic. The transmission has no idea which gear to use, it shifts like a bowling ball in a barrel.
Clunks upshifting and downshifting. The other problem is the shimmy/wobble. I have it in spades. The car always feels like it is hitting small strips in the road with a constant vibration in the front. The dealer cannot find the problem even though VW is trying to figure it out. (I have a feeling this isn't the first time). It is the worst driving car I have ever owned. Would much rather drive my 04 GTI with 100,000 miles and worn tires.
View 14 Replies
Not sure what caused it to break but my front driveshaft split in half. I had it in 4wd and was doing a K turn to back in my driveway in a snow storm.
I got underneath in the snow (miserable) and wasn't able to come close to getting it off. The bolts holding the shaft onto the t-case will not budge and the tiny 5/16" bolts stripped all my small 1/4" sockets. I'm guessing I need a 3/8" drive 5/16" for front and the rear just spins. Any tricks to getting this off the truck.
View 14 Replies
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
View 12 Replies
I am a new 6.7 owner and had/ have a 7.3 As I have been getting to know the truck I have been under it and noticed that the front drive shaft and axle are locked in. My hubs are switched to auto but I know on my 2000 7.3 when my hubs are on auto my front axle and driveshaft are disengaged... I'm wondering if the new 4x4 system is different. I know that can save on MPG
View 6 Replies
I recently bought a 1997 F150 4wd 5sp manual. While changing the fluids, I noticed that the front u joint on the rear drive shaft has a grease fitting. No matter how I rotate that shaft, I cannot access that fitting with my grease gun, even when fitted with a flexible rubber hose.
View 14 Replies
After installing the lift on my 6.2 F250 I ran into the well known issue where the front drive shaft hits the catalytic converter. The two options I was told that I had was to weld in a slight jog into the exhaust guts to go around the cat or to get a smaller diameter drive shaft... I had the truck down at my local exhaust shop to have a new cat back system installed and I had the exhaust guy throw in his .02 about what to do.
He came up with a super easy/obvious fix. When the left and right exhaust meet up before the collector there is a welded brace that secures both sides together. He cut about .5" out of it and loosened the flanges and shifted the exhaust over. Welded the brace back up... Works perfect.
View 3 Replies
I have a 2004 F350 Crew Cab DRW 4WD 6.0L.
The front drive shaft is making a high pitched metallic squeal while the truck is in motion. I thought it might be the universal joints but after lubricating the joints, I can still hear the squeal and it sounds like it is coming from inside the drive shaft. I also hear this squeal when I spin the drive shaft by hand.
I have quite a few questions about these drive shafts:
- What would cause a squeal from within the drive shaft?
- Are there any replaceable parts or do I have to get a new drive shaft?
- How do I identify the correct drive shaft part for my truck? Seems like there are a LOT of different models on the web.
- Are any of the aftermarket drive shafts any good? Any to avoid?
- Is this a DIY job or will I need to take it in to the shop?
View 3 Replies
I want to install a new front drive shaft in my 2000 F350. I have the new one, and it has a big nut and it is threaded for length adjustment. My old one has a rubber boot which is missing from the new one. I plan on using red locktite but I do not know the torque specs on the front universal caps. Should I take it to my mechanic? I've never owned a 4x4 before.
View 3 Replies
2001 Jimmy 4wd, 115,000 miles; Recently I noticed a strong vibration when in 4WD, no vibration in 2wd. I found that the rear joint (at the transfer case) of the front drive shaft has play in it. I am assuming that this is the problem. It has the appearance of a CV joint. Is that joint rebuildable or do I need to replace the shaft?
View 1 Replies
My 1994 Chevy Suburban will not engage the front drive shaft. It has an electric actuator and it will not engage. the transfer case engages but not the front axal. When I shift the transfer case into 4Hi or 4Low it will shift itself but the light will not turn on. I have heared rumors that you might have to manualy connect it to the battery and have a kill switch in the cab. What is the problem and should I connect it manualy?
View 6 Replies
