Ford Transmission :: 2006 F350 5.4L 5R110W - Replaced Solenoid - Locked Up - Code P0743?
Aug 15, 2016
2006 F350 5.4L 5R110W
I've had the TCC solenoid replaced. Not long after, it locked up again. I had the whole solenoid body (including harness & sensors) replaced .....continues to run hot and eventually lock up. IIRC, it gives code P0743
Transmission shop seems to think it's an electrical issue outside the transmission and thus not something they can deal with.
I took it to a dealership and they said that if it was an electrical issue outside the transmission, it would be throwing codes every time I start it up....which it isn't. They would start be replacing the solenoid (and possibly the whole body) with 'brand new' parts.
View 4 Replies
Advertisement
2005 Ford F250 4x4 XL 5.4L 5R110W WITH 177,600 MILES... Tow Haul light flashed after 78 miles (along with other codes) after purchased. I purchased it used. While driving transmission would stop pulling as if it went into neutral and slam back into gear, at same time Tow Haul light be flashing...
Code is P0760 shift solenoid #3, I read from the forums on the site one caused could be the ground wire. We installed a ground strap from battery to tranny
Still does the same.
I have a shift solenoid ordered if needed, knowing the location of #3 solenoid in the tranny is the key to not having to keep dropping the pan. I love this site and have been reading it for long time.
View 9 Replies
I have a 1997 Dodge Avenger ES that reads code P0743 Torque Converter Clutch Solenoid. I've replaced the transmission control module, and filter. I've called the Dodge dealership and asked if the new transmission control module needs to be programmed. The service department said "Possibly" I said "Well it's shifting better than before. If there wasn't any firmware on it what would it do?" He said "My guess it that the car wouldn't shift." I asked if the Torque Converter Clutch Solenoid visible once you remove the filter. He said "I'm not sure." Clearly, my car isn't going there. Then asked to be transfer to the Parts department to see if there was a part called Torque converter clutch solenoid. That answer was "No" there isn't a part listed called "Torque Converter Clutch Solenoid". What should I do or try?
View 9 Replies
I've got a 2006 F250 6.0 5R110W 4wd 220,000 miles It started getting a slight delay going into reverse and tow light flashing last week. all else functioning perfect Got a pending code P0700 and P0741 I stopped at NAPA when I was leaving no reverse checked every thing all was normal no leaks and fluid good color drove perfect in drive I got back to the shop [10 miles] put truck in park it was like its still in drive same with neutral, in reverse it wants to creep forward.
View 1 Replies
On my 2006 Ford F150 2WD, v6 automatic, the overdrive dash lamp is blinking, I get a engine light and the code I get is a P0743. That indicates the solenoid or wiring is bad, but everything works just fine. The transmission is running fine, clear fluid - no odor. The overdrive works and the truck shifts like new. When I start, the "OD-OFF" light immediately starts blinking and never changes. I can activate the OD normally and it doesn't effect the blinking light.
Where to start? I suspect that since all is functioning well, the issue is with the signal to the ecm? By the way, I can clear the code so that the engine light goes off, but the "OD-OFF" light remains blinking.
View 14 Replies
I've a 2006 sonata 3.3 with 100k miles on it and recently it started going to limp mode leaving me in 3rd gear only after scanning it I've found code p0743 (TCC selonoid open/short circuit) what to check from here or can share any wiring diagrams for this particular circuit I'm not sure where to start. where is the wiring harness for that is located ? is it in the oil pan ? and if I wanted to pull the selonoid itself to check would it be something I can do myself ?
View 9 Replies
Well, I've been getting a flashing OD light, so doing some research, led me to replace the shift solenoid. I did just that and have yet again the same P0741 code... The truck seems to shift normal but will randomly throw the code and then will not go into Overdrive as well as shift very hard into all gear. Where to look next?
View 1 Replies
I had a 622 code so I replaced the solenoid pack . Took care of problem for a week or so with no issues... now it's back again... now it start 1st when we had heavy rain then it started again just today in heavy rain? Short maybe?
View 4 Replies
I have been recently told that it is bad to drive my F350 with the manual hubs locked when I do not have it in 4 wheel drive mode. There are times when plowing snow that the roads are cleared but I am still plowing driveways. I do not want to travel with 4 wheel engaged in the scenario. So I would just disengage 4 wheel and travel to next stop. Is this a bad procedure?
View 10 Replies
My old 97 f-150's 4R70W started slipping.....so I just installed a rebuilt 98 f-150 unit that had about 10,000 miles on it and also has a transgo shift kit. Got it finished today....and.....
I have an check engine light code p0750 "shift solenoid A malfunction"........when leaving from a stop in Drive, the truck starts going in 2nd gear and just skips 1st gear all together. If I manually shift it, then 1st works fine and shifts through all the gears fine.
But in Drive.. it skips 1st. What to do? or what could be the problem? Where is this solenoid? Can I swap the one out of my old tranny into this one without pulling the whole tranny apart? (I don't mind dropping the pan though...) Or could i have a bad connection somewhere maybe?
Also....When the tranny shifts from 2nd to 3rd the rpms jump about 500 rpm before they drop...kind of seems excessive. Could this be caused by the shift solenoid A malfunction?
View 4 Replies
2002 Camry 4 cyclinder. P0128 code - replaced the thermostat and coolant. P0128 code is now locked in. Lifetd the battery cable, but it is still there when I start the engine - or - it comes comes back immediately when I start the engine. Coolant temperature looks normal on the dashboard gage when I drive the car. What should I do now?
View 3 Replies
I am getting a single code - P0753 that comes on now and the van will not shit into 4th gear. It re-appears after clearing the check engine codes in 5 seconds. That seems to be the "A" or 1-2 shift soleniods (or wiring).
Can you get to the shift solenoids after dropping the transmission oil pan or do you have to pull off the side housing cover - that seems like a much more difficult job?
Of course, I will replace both of the solenoids if I can get to them. I will do it myself if I can get to them after dropping the pan but don't know if I will be able if that side cover has to come off.
What is the location and if I should be able to get that drivers side cover off if that is where they are?
I think the 1998 Venture's tranny is the 4T60-E.
I have a 1000+ mile road trip coming up soon so I got to get this fixed shortly. I guess I am glad this didn't happen in the middle of the trip though.
View 6 Replies
I'm trying to find information about replacing solenoid in my transmission. I have pdf of repair manual, and it doesn't have much information regarding transmission.
I have a p0766 code, and I think I need to replace Shift Solenoid. Does Technical Information Service Cover this with subscription.
View 1 Replies
On the way home tonight, the O/D light started flashing. I happened to have the Bluetooth OBD adapter with me, so I plugged it in and opened Torque. It comes up with a "pending" code of P0743. After a little bit, the light quit flashing so we drove the last mile home. The O/D light began flashing again the last couple hundred feet before our driveway. There didn't seem to be any loss of power or anything like that the whole time.
After we got the kids to bed I went back out to check the fluid level. (It had cooled some, so I let it run a bit before I checked it - the light wasn't flashing this time.) The level is at the second dot, right below the crosshatch. It's almost transparent, but I don't know when it was last flushed (if ever). From what I've seen on here, I'm guessing this is an electrical short somewhere?
View 14 Replies
Having problem with 5R110W direct clutch. My nephew had his 2005 SD f 250 6.0 be told that 5R110W direct clutch problems. He was towing a trailer in tow mode and it started slipping in and out, so he took it to a dealer and they said that it was the direct clutch that was causing the problem and needed to be rebuilt, he only has 40000 miles on it but they said that it is out of warranty. What do you guys think that he should do?
View 12 Replies
I have a 2003 F-250 Super Duty 6.0 4WD that has about 202,000 miles on it. I bought the truck with 83,000 miles on it and have never serviced the Torqueshift 5R110W Hi-Torque transmission. No new filters, no new fluid. In the interest of gettting the most life out of the truck I am trying to be a bit more proactive with maintenance. Does a flush/power purge will precipitate transmission problems? I am even concerned that dropping the pan and changing the filters and topping off fluid may cause problems. There are no problems presently and the dealership can't tell me that the've ever performed a transmission service for the previous owner via OASIS. Can I get away with a filter change and fluid top-off at a decent interval without incurring a condition that will require the transmission to be pulled and rebuilt?
View 10 Replies
I have a 98 camry with code p0755 - shift solenoid valve#2 malfunction.-What are some of the most common causes. How to test it ,the issues that cause this and what to do also after replacing it if bad? Also are these to be replaced in pairs with both 1st -2nd shift and 2nd to 3rd shift .
If I have high miles on it will adding the 2 -3 quarts of new fluid give me issues as to mixing with the old and part breaking up in transmission(I've heard a lot happens when u replace very old fluid with new or flush it fully)..will be replacing filter also but not the rest of fluid still in transmission at this time. Looking for a link a pic. of the exact location on transmission inside pan .of it(looks similar to other shift solenoid near it )...
View 3 Replies
So I'm off work today, and want to service the transmission. I've got both filters, and a 18 quarts of SP, but am not familiar with this transmission, and understand there's no drain plug for the converter. Want to get all of the fluid out, best I can. I'm at 153,000 on this truck with no issues. I do not desire to flush, just want a fluid change.
Searching the forums brings up a lengthy list of transmission threads, but nothing yet that gives me the step-by-step.
View 14 Replies
For the last few weeks I have noticed my transmission overheating a bit, nothing bad, but I have just been running around town local so no drives over about 15-20 mins.
Well, Friday night I went out to see a friends band play about 40 mins away, My trans temp climbed steadily the whole way out there, peaking at 226 by the time I got out there. I kinda took my time getting home hopping bars to give the trans a break to cool off.
Did some diagnosis today, first thing I did was unhook the line going to the rear of the transmission and did the bucket flow test. I fired it up and fluid came pouring out of the line which goes into the rear of the trans, nothing really came out of the rear of the trans, it was all out of the line.
So that tells me that its getting flow through the coolers. I didn't measure the amount like some do, but I can tell you it looked like a strong steady flow.
I made sure the fluid levels are proper as well which they are, it was maybe a 1 quart low which shouldn't effect anything. I also inspected the coolers and everything appears to be clean with no airflow restrictions. Took it out for a brief drive again and it climbed up to 147, maybe 5 miles out 5 miles back. Ambient temp is 62 today.
I am getting multiple codes on my Edge Evo which I have had set to stock settings since I bought the truck. Codes I get that concern me relevant to the trans are P0741 and P0743. Both seem to relate to the torque converter.
I feel like my RPMs are a bit to high at highways speeds so I am wondering if I have a TC that is slipping a bit while driving. I did notice a bit of a metallic pearl in the fluid that came out. Aside from that I feel like the trans is shifting ok, though sometimes I have to let off the gas to get it to shift into 4th.
View 3 Replies
I have to fix the truck. Battery is pretty new, replaced solenoid next to battery this morning. Truck still won't start, just clicking away. Decided I needed to replace the starter, put the truck on jacks and went to the starter. At the starter solenoid there is a red cable attached, and a "loose" red wire, with a connector on the end. It would appear the connector just needs to be reconnected to the solenoid. But it won't "connect". Am I missing something? Should it not connect to the prong on the solenoid? Should I just replace the starter, and forget about the wire? I do have Chiltons for our truck, but it doesn't show a picture of the prong on the starter solenoid.
View 11 Replies
I bought the car with 117k and never since my possession bothered to service it. Why? I kept putting it off well at 165k I said heck ill do it. Currently at 170k my gear wont shift past third and its reoccurring almost daily. When I first bought it it was intermittent. I think the late service messed it up. Here's the thing, aamco will open up my pan and look at my solenoids which is 250ish.
View 14 Replies
