Ford Transmission :: 2002 F250 - No Reverse OD Light Blinks?
Sep 13, 2013
I've got a 2002 f250 7.3L 4x4 auto trans and I've done quite a bit of searching and cant seem to find any definite answer. I drove 40 miles today no problem. pulled into a stall at sonic and when I went to leave no reverse. I was even on a downhill slope, but it wouldn't budge. I got a friend to come up there and we tried to pull it, wouldn't budge.... I disconnected the driveshaft and it rolled downhill without us even having to hook onto it again. Once it was out I hopped in and put it in drive and it took right off.
It did feel like maybe I had to give it a little extra gas to get it moving but maybe I'm just paranoid. I know once I got on the road it was cruising 65 no problem in drive. I got it to my job and noticed that when I put it in reverse the OD off light flashes and if I mash the gas with it in reverse it actually acts like its trying to push it forwards. I did jack the rear end up and put it in reverse and the tires make a half rotation but in the wrong direction then come to a dead stop.... with the tires jacked up off the ground Drive would spin them, 2 would spin them, but 1 would stop them like somebody locked up the brakes.
View 7 Replies
Advertisement
I pulled my CD player and put it back in and now my air bag light won't go out when it self tests. It blinks for a while then stays on steady. What's up with that -- I thought I was having enough problems with the CD player as it was?
View 14 Replies
My 2002 explorer, 4.0l engine. My 4x4 light on the dash blinks 10 times and I've found that sometimes the 4 wheel drive locks in. When i pull into a parking space on dry road I can feel the front of the truck Jerking when trying to park. I hit the 4x4 auto button on the dash a couple of times and the 4 x 4 will disengage. While driving on dry road yesterday the 4x4 light started blinking and I felt the 4x4 slam in. The 4x4 light still blinks and I can't disengage the 4 x 4 this time. The truck has 140,000 miles on it. I'm thinking its the 4x4 control module but I'm not sure.
View 1 Replies
I have a 2002 f250 CC 4wd 7.3 and I have no power to my reverse light sockets. I am stumped, all my fuses are good, I don't think there's a relay so i haven't checked that. My neutral safety switch is good, I'm getting power to both the blue/pink and black/pink wire. What it could be, at first it was constantly blowing fuse 27 every time I put it in reverse but then it stopped blowing it obviously because they won't come on.
View 8 Replies
I have a 98 f150 4.6 v8. when i start driving and i hit about 40 my truck doesn't want to shift, i have to take my foot off the gas, let it shift then apply the gas again. if i don't it shifts real hard or the RPM's go real high. and then every so often my overdrive off light blinks. it shifts in and out of overdrive ok though.
View 2 Replies
I was driving down the freeway the other day and when I hit a rough patch of road, nothing major, the truck sputtered and the 4x4 Low light blinked a few times on the console. I was driving in 2wd at the time. I kept driving and every bump I hit the truck sputtered as though trying to shift and the light blinked. On smooth road it didn't happen.
Today I drove to work at 6:30AM (40 miles), no issue. At noon I drove home and the issue started again. Every bump I hit the light came on and the truck seemed to want to try and shift into 4x4 low.
I got home, parked the truck for a few hours, then went out again, no issue. But about 20 minutes later it started again. I pulled over shifted to 4x4 high, drove it, was fine, went into 4x4 low seemed fine, went back to 2wd drove it some more issue came back. I've read tons of online threads regarding 4x4 lights etc, none like this and none on F250 Super Duty (2008).
View 14 Replies
I've got a 2006 f250 with 160,000 miles, trans was rebuilt by previous owner about 10,000 miles ago. The tow/haul light started blinking yesterday, only blinks for first couple of minutes of driving and then stops. Service engine light popped on today as well. Won't have access to a code reader until tomorrow, but looking for some preliminary info...
View 3 Replies
I have a 2004 F250 Torqshift trans, 155,000 miles. It has had a slight hesitation when trans is engaged for about 4 years, not a problem the dealer has no fix they said.
Now today for the first time I had a tow haul light come on while driving on the freeway. It would not go into overdrive and the light keep blinking. Later in the day, I let it cool down and it drove fine to the store about 2 miles. When I got in to drive home it had tow haul light go blinking and check engine light came on this time.
I hooked up my code reader and it's giving codes: P0720, P0751 and P0766.
Should I take it to the Ford dealer, a Transmission shop or have a friend who worked at Ford Dealer do the Work? I see that some people have changed out the TFT sensor and corrected the problem. While the pan is down should I just have all the shift solenoid sensors changed?
View 11 Replies
when i turn on my car it shakes and engine light blinks it happen this morning when i start my car.
View 1 Replies
I got Ford C6 Transmission bolted up to a 460 in a 1978 Ford F250 4x4. I recently had put all new gaskets in it and I change the fluid. The day I put it all back in my reverse was trying to lunge forward, my natural was a 1st gear, and drive was working fine. Now recently my park throws itself into gear. I got no burnt fluid, the clutches were fine when I put it back in???? What could it be, I'm running out of options before I do a manual transmission swap.
View 7 Replies
So last weekend I installed a transgo kit for my 4R100 transmission in my 2000 F250 diesel. I didn't really care about getting a shift kit, but I had problems with delayed shifts and figured the accumulator springs had broken. It turns out that was correct, the 2nd gear spring came out in 8 pieces.
Anyway, the transmission shifts great now, but when I put it in reverse it the engine jumps up 200 rpm and then it bogs down as it engages reverse forcefully. It also does this while selecting 1st from Park.
From what I'm reading it's the TC not unlocking and/or a fluid pressure/volume issue. I've also read the filter might have fallen off, I had a hell of a time keeping it in place. I've checked the the fluid level and everything is good there. My question is when I drop the pan, aside from the filter, what should I look for?
View 4 Replies
I recently bought a decent looking 1999 f250 4x4 5.4 auto. It has no forward gears and will only move in reverse. I topped off the fluids and have found no leaks so far the cooler lines are crusty but dry. I am gonna need to swap this thing out or do some more trouble shooting if there may be a non rebuild issue to solve.
View 4 Replies
I have a '95 F-250 7.3 auto 4X4. The transfer case linkage has been floppy and prone to coming apart since I've had it, but that's been fine for me. I let my brother use the truck last weekend, and now it does the following: When you put the transmission in reverse, or when the truck overruns the engine (compression braking) it grinds badly like the transfer case isn't quite engaged. Only does it in 2 or 4 Hi, and everything's normal otherwise.
Could the transfer case have jumped out of gear while he was driving it, and he didn't know to either push it into gear or pull it into neutral before it did damage? I really don't want to pull a transfer case in my driveway in December in New England, but give it to me straight.
View 9 Replies
We installed a TransGo HD-2 "reprogramming kit" into my friends 96 F-250 460 4x4 E4OD in preparation for future engine modifications. The problem is it didn't work correctly.
All forward gears work (some shifts are harder then stock, but many of the shifts are just as soft as stock, which in itself may be another issue). We drilled the separator plate for the V8, we may try the diesel size next though...1st, 2nd, 3rd, 4th + tq lockup all work however.
Anyways, the major problem is that it no longer has reverse. If you shift from reverse to neutral, the RPM seems to go up a little bit as if it were in gear a bit, but give it some gas and it acts like it is in neutral. Obviously something went very wrong.
View 10 Replies
I have a 1970 f250 with a factory 390 (vin verified) and a C6, I believe the transmission was rebuilt but have no way to verify. It works fine while cold and mildly warm. Once heat soaked it is very slow to shift (going from neutral to reverse can take almost 30 sec) and leaks profusely from the front. I can not tell exactly where the leak is. Could this be a case of just having too much fluid or is there a more serious concern? The dipstick does read high but level ground in my area is hard to come by so the accuracy can be questioned. If it does have to much fluid, do I just drain the pan, re-install and let it run till hot and replace fluid as needed or should I drain and replace with 3 qrts prior to starting?
View 7 Replies
I've got a 76 F-250 4x4 C6 and the transmission has been kind of quirky since I've owned it. I'm starting to tow with it occasionally and I'd like to get this sorted out. It only has issues cold. After 5 minutes at most its good to go, probably more like 2-3 minutes. After that it works 100% as it should.
When cold, reverse is really weak. If I fire it up cold and go for reverse it will hardly move. If I put it in neutral and run it at 2000rpm for about 30 seconds it will pull but still weak. And after getting out on the road 1st and 2nd are great but 3rd gear is basically non-existent, all slip. I just hold it in 2nd for a few minutes then its fine. There are absolutely no issues when it warms up. I was towing my Bronco with it and absolutely no slippage at all. I'm dealing with it for now. Don't back up when cold and hold it in 2nd for a bit when cold only. That or rev it before reverse etc.
I have adjusted the band. I have never changed the fluid. I did buy new fluid for it but have not done it. Who knows that kind of fluid is even in it. The fluid is a little dark but its really not that bad and doesn't smell burnt. I'm in the market for a 4 door super duty so I might just have to limp it along until then.
View 3 Replies
1996 F250. I think its a Ford works great until yesterday. Put it in reverse had to rev it up to get it to move and when it did kind shook and sliped an does back up but doesn't like it....
View 5 Replies
I've got a 2006 F250 6.0 5R110W 4wd 220,000 miles It started getting a slight delay going into reverse and tow light flashing last week. all else functioning perfect Got a pending code P0700 and P0741 I stopped at NAPA when I was leaving no reverse checked every thing all was normal no leaks and fluid good color drove perfect in drive I got back to the shop [10 miles] put truck in park it was like its still in drive same with neutral, in reverse it wants to creep forward.
View 1 Replies
Anything else that could cause reverse to go out of an automatic tranny other than the tranny being shot? I don't know of anything but any way to keep me from replacing a tranny.
View 2 Replies
1991 4x4 f250 idi w e4od w 3:55 ratio... The truck is slow to engage in reverse, about 5-10 sec. It also has a very hard shift 1-2. All other shift points are good. Drop down is good, and TC lock up happens at all the right points (feels like anyway).
I've had the truck for about 2 years now, replaced several sensors an harnesses and a full fluid change to solve other problems but this still remains.
Sometimes when I start it in the morning if I let it sit and idle for a few min it will engage reverse much quicker AND shifts way smoother and constant. Shifts smoothly thro all gears, holding a constant 1800-2000 rpms with no drop or lug. Or do I need a rebuild?
View 4 Replies
I have a 2001 F250 V10,
So the truck drove fine yesterday had zero issues... I used my auto start as I do every morning in this cold weather, get into the truck and shift from park to drive and its like it does nothing. I can free rev in N,D,1,2. Reverse works great.
I tried switching from 4wd to 2wd, no change. Reverse works just fine. No noises, codes or anything, just doesn't want to engage...
I am assuming I have a 4R100. Could something electrical cause this? I am thinking its mechanical, but hoping someone has ran into this before.
Literally no way I would have known the trans was going bad... It's always worked fine. Tranny fluid is full, I tried unplugging the battery waiting and plugging back in, no dice.
View 11 Replies
