Ford Transmission :: 2000 F150 - Transmission Holding 2nd Gear Too Long Before Shifting Into 3rd
Dec 29, 2014
I have a 2000 F150 5.4L with 157k miles on it. I think it has the 4r70w trans. The transmission has started holding 2nd gear too long before shifting into third. Throttle position doesn't matter, it does it even under light throttle. I do not have a check engine light. I have owned the truck since new and the trans fluid has been changed 3 or 4 times. The fluid looks pretty good now, not burnt or anything. The truck has been sitting in the garage a lot over the past 2 years, I drive it at least once a month and have put maybe 2000 miles on it this year. It shifts fine through the other gears, just 2-3 has an issue. Truck has the towing package.
View 6 Replies
Advertisement
This is an Auto/4z4/4.6 V-8. It's Skidding or a Clutch is not holding at times when shifting up or down while on Cruise and slight hills.
someone suggested changing oil and filter about two years ago. I did that and it didn't change a thing. $145 that time.
I'd like to know if its the clutch in the torque converter, or the Transmission? If I have to change something out, should I get both?
View 3 Replies
My 94 F150 has been actingup lately with the 4r70 transmission not shifting into 3rd gear or above. I replaced the MLPS sensor and re pinned the plug as per the instructions with the switch.The old sensor had the plug on the side, same type of plug, but wires indifferent spots. Truck wouldn't start like that, so repinned to match the instructions. I couldn't get the neutral mark to 100% line up as there is not enough adjustment, but it is very close.
The old plug had
32-298-140-33
57-199-359-463
I switched it to
57-359-199-463
33-140-298-32
Then tried
463-359-199-57
33-140-298-32
Truck still won't shift to 3rd, overdrive off button doesn't light up and itwon't start in neutral. I tested the ground at the connector and it lights up atest light connected to the pos bat cable with no issues.
Back up lights won't work, but flicker as going from R to N, so I suspect that is due to the fact I couldn't get the marks to line up 100%, but i'm not worried about that now.
View 1 Replies
I have a 2008 Ford Escape 2.3L V6. About 67K miles on it.
Recently there's been some transmission problems. When the selector is in Drive, it will take abnormally long to shift into the next gear at normal speeds, and will redline if i hit it hard, but if i let off the gas, it will shift. Never hard.
If I put the selector in 2, it will do the same thing, eventually shifting into that second gear.
Gear selector on one, well, it obviously stays in 1st.
Reverse is fine. All shifts are smooth just take forever, and I get the wrench in the dash (means drivetrain/throttle fault as per manual) only after driving a while. The tranny fluid is still very clean, and this as been going on for 2 months.
Ive taken it to about 6 different places. Half say new tranny off the bat. Other half says clean fluid for that long after the problem started means its def. an electrical problem, and that makes the most sense to me. What it could be?
I'm thinking:
-Tranny Range Positioning Sensor
-Input/Output speed sensor
-TCM reprogramming/replace
- I'll even go with reflashing the PCM.
View 7 Replies
I am having a few issues with my 2001 accent. I bought this car for around 500 bucks after my friend hit 3 deer with it. At 101,000 miles the transmission went on it and he had it replace with a new one. At about 113k he hit his third deer and parked it. I bought it off him a few years later and its been running great. It died on me one time and it was the crank position sensor. Now I have about a 156k mile on it and it will not go into overdrive.
I have gotten mis fire codes, I know it needs new O2 sensors, and also P0733 Gear 3 Incorrect ratio. The button on the shifter does nothing, If i press it on or off the light does not come on on my dash. I noticed it was not going into OD this last winter if i dropped it into low and shifted to drive it would no longer go into overdrive until i placed it in park and then drive again. Ive been searching everywhere for an answer I was reading one post that it could be the TPS sensor causing issues but i haven't had time to check the voltage.
View 5 Replies
I come today for a apparently transmission problem. I have an automatic VW Jetta 2000 2.0 that i bought a few months ago, the car is great, has 250K miles.
The problem is in the morning when car is still cold, the transmission isn't shifting gear until 3K RPM (For 1-2 is about 2.5K RPM, and 2-3 is about 3K RPM). After 5 minutes of driving all back to normality and transmission shift gear about 2.2K to 2.3K RPM.
The question is: this is normal?, what could be wrong?.
View 7 Replies
I have a 2001 Hyundai Accent with 120,000 miles on it. Up until a few months ago, its been a great little car. The transmission started acting funny by shifting irregularly and then getting stuck in 3rd gear occasionally. I took it to the dealer and they told me that the tranny is shot. The estimate for the repair is $2000.00.
I just can't see putting that much money into this car. It needs Struts, Shocks and a timing belt. Basically what it needs is what its worth if it were running well.
How hard it is to replace the transmission in this car? I have the 1.6L DOHC with the Automatic transmission.
View 12 Replies
1986 F150 3spd Auto 300 v6. My truck will not shift out of 1st in Drive, to shift into second I have to column shift to 2nd. 20mph top speed and idk what to do to fix it. I would like to put a 5 spd manual in it cause I would like to drive over 50mph.
View 4 Replies
I have a 02 f150 4x4 5.4 135 k the transmission will not shift into drive unless you rev it up to about 1500 rpm and when it shifts it goes in very hard but when you get moving it seems to work ok but every time you stop or slow way down it does the same thing. It works fine in reverse and the oil and filter is good. I am thinking TC but i dont know ...
View 3 Replies
96 F150 carbed 300 with a C6/208 SAS44/9" with 3.55 on 35s.
I put a transgo shift kit in the transmission before putting it in the truck, it also has a small stall. At half throttle you can manually shift 1-2-3 with no issue at all. Under full throttle when you shift to second it won't go into second until you push the shifter into third. Then it'll go to second and spin the tires when it grabs second in dirt. This is all in 4lo, I was gonna switch to 2hi and try it but it's raining and I don't feel like crawling under it to change it. The truck is a mud toy so will spend 90% of its time in 4lo.
I don't have a vacuum line currently hooked to the transmission because I have the same shiftkit (transgo) in my 77 and no vacuum line on it either and it works fine.
View 4 Replies
My 2000 Civic DX has approx. 55K miles on it. For the past several weeks, the Automatic transmission gear is resisting/sticking about half the time when shifting from Drive to Park and vice versa. (In November 2010 I had a local mechanic-- whom I found on Yelp and who has done other work including replacing the timing belt--replace the ATF, telling him he had to use Honda fluid). What is causing the sticking?
View 3 Replies
1998 Ford f150 172984 miles automatic with 4x4 runs and drives transmission is going out will not hit 3rd gear have to drive in 2nd. Is there a fix without pulling the transmission?
View 5 Replies
My manual transmission got stuck in 4th because of a melted oil trough sticking between the gears. I got all the plastic out, and the dog clutches/collars are "free." But, I don't know how to put the gears back into neutral. When it's reassembled, the stick doesn't work to change the gears. How can I get the gearbox back into neutral?
View 19 Replies
My 82 f150 4x4 302 c6 trans is acting up. My c6 is slow to shift into any gear when I shift the column shifter, after a moment it jerks into gear, also it doesn't seem D is doing anything but all the other gears seems to function manually or auto.
Fluid level looks ok, maybe a little high on the dipstick. I'm going to check the modulator and do a fluid/filter change but looking for a link to the band adjustment screw ?
View 3 Replies
I have a 2007 F150 FX4 with 105K on it. When it goes from 2nd into 3rd, it acts like it's in neutral. There's nothing there. This is in "D" with "OD" on. If i turn OD off, it will wind up and grab 2nd again and will coast if I let off the gas. Also, if I manually shift into 2nd, it will engage 2nd and I'll have engine braking if I let off the gas.
The trans fluid was full and bright red as is should be with no burnt smell to it.
I dropped the pan and the magnet was a little fuzzy with some metal filings but there was no metal laying in the pan. I also dropped the valve body and there were no broken snap rings and the e-clip on the OD servo was intact. The valve body was also clear of anything that shouldn't be there. I'm hoping that I can replace the shift solenoid and that will solve my issues.
View 4 Replies
04' Ford Explorer - 4.6l Automatic 4x4 - 138,000 miles... While driving today my transmission hesitated a long time between 2-3 gear and RPM went higher than normal. After coming to a stop a taking off again, long hesitation, slams into 3rd gear, check transmission warning came on and OD light on dash was blinking. I drive it home and pull the code: P0745. I drop the pan and find a piece of metal 1/4 wide x 1/2 long. Does this mean a complete trans rebuild?
View 5 Replies
I just got my 03 F-150 with 112k on the clock. It has the manual 5 speed tranny behind the 4.6L.
However, since I've gotten the truck, it's kind of difficult to put in first gear. If you are sitting at a light and in neutral and the light changes and you push the clutch to the floor and put it in 1st (fairly quickly - a normal reaction time), it will actually do a little grind and/or thump. However, if push the clutch to the floor and wait a couple of seconds and then shift into first, it's a bit of a "push" but it will go in without grinding.
Once in a while shifting to 3rd it feels the same way, but won't really grind.
I'm just wondering if that means the clutch is toast or is it the trans that is toast? Reason I ask is my 96 Cobra with the T-45 5 speed would grind going into 5th gear if I just normally put it in. I used to have to put it in neutral and then push the clutch in again and slowly shift to 5th for it not to grind. And it wouldn't go into 3rd if I tried to shift fast or under power. I replaced the clutch and found out the trans was actually going bad, but it had 173k on the clock.
So, I'm really paranoid that it's my darn trans in the truck instead of just the clutch. Whenever my old Camaro clutches used to be dying, they would slip more than they would ever grind going into a gear.
View 14 Replies
I think my E4OD in my 95 f150 is slipping in 4th gear. Just started the last couple of days, the engine rpms stay steady but the speedometer bounces around 3 to 5 mph. Thinking rebuild of the trans....
View 7 Replies
Have a 2000 expedition with 84,000 miles. Tranny seems to shift hard from first to second gear. Its been 24,000 miles since my last dealer tranny service. Thinking of getting a new service now before the recommended 30,000 manual recommendation. Whats happening?
View 6 Replies
I posted earlier this month about my 1996 Ford F150 4x4 manual tranny truck. It had gotten stuck in fourth gear, and I, along with others, assumed it was the shift forks. I cracked open the top of the transmission yesterday, and what do I see? Melted plastic staring back at me. What's going on here? There was melted plastic jammed between fourth gear and the inner wall.
Is this a case of the surgeon leaving his instruments inside the patient? Could a mechanic have dropped his tuna sandwich wrapper in the transmission at some time?
View 8 Replies
79 F150 400/C6 2wd. Loss of reverse and it doesn't want to stay in high.
Strange thing happened today. I took my truck on it's longest test drive since rebuilding the transmission. It was about 25 miles. I got to the junk yard just fine and it was running just fine when I left. I went through a drive through to grab a burger and headed home. That's when it started acting funny. It shifted fine 1st to 2nd, then 2nd to 3rd, but it wouldn't stay in 3rd. It would shift into high, but the slightest bit of throttle and it would shift back into 2nd and eventually got so bad that it just stayed in 2nd, so I had to return to the town I was leaving.
I drove to an autoparts store nearby. I decided to move where I was parked and when I put it into reverse, nothing was there. It rolled back. I drove it to the new spot and called for a tow truck. Weird thing is that reverse worked just 10 minutes earlier when I left the junk yard. When I got it home 2 hours later, it backed up under it's own power. I let it cool down completely and took it for a test drive and it drove perfectly. I have a few theories or questions:
Kickdown rod: Can it be in such a position that it could take away reverse? I would assume that if the spring wasn't returning it all the way forward that it wouldn't have shifted from 1st to 2nd properly. I ask this because I am not using the Holley spring mount and I'm wondering if the wrong spring set up allows the kickdown to be partially activated.
Fluid: What fluid are you suppose to use after a rebuild and what fluid can't you use. Mercon V says it supercedes earlier fluids, but is that wrong?
Am I wrong to assume that if fluid was the problem that I would have had problems with 1st and 2nd?
Cooling: What are signs of hot fluid other than smelling it. Once again, assuming I would have problems with all gears if fluid was too hot.
My guess is that something is sticking in the valve body, but before I drop the pan and pull out the valve body, I want to make sure all other avenues are exhausted.
View 14 Replies
