Ford Transmission :: 1996 F150 Not Shifting Into Second Under Full Throttle
Aug 13, 2017
96 F150 carbed 300 with a C6/208 SAS44/9" with 3.55 on 35s.
I put a transgo shift kit in the transmission before putting it in the truck, it also has a small stall. At half throttle you can manually shift 1-2-3 with no issue at all. Under full throttle when you shift to second it won't go into second until you push the shifter into third. Then it'll go to second and spin the tires when it grabs second in dirt. This is all in 4lo, I was gonna switch to 2hi and try it but it's raining and I don't feel like crawling under it to change it. The truck is a mud toy so will spend 90% of its time in 4lo.
I don't have a vacuum line currently hooked to the transmission because I have the same shiftkit (transgo) in my 77 and no vacuum line on it either and it works fine.
View 4 Replies
Advertisement
I recently purchased a '13 FX4, i love the truck, the Ecoboost power is incrediable. Recently while passing someone it made a horrible grinding sound, the dealer advised that it was known turbo issue that should have been corrected before we took delivery of the truck. When we took it in the dealer called and said they have Ford corporate involed because when the truck reaches WFO the four wheel drive tries to engage. Said it might be soem sort of vacuum issue.
Specs : 2013 Ecoboost Screw FX4 short bed. No mods, 6500 miles.
View 10 Replies
I have a 2000 F150 5.4L with 157k miles on it. I think it has the 4r70w trans. The transmission has started holding 2nd gear too long before shifting into third. Throttle position doesn't matter, it does it even under light throttle. I do not have a check engine light. I have owned the truck since new and the trans fluid has been changed 3 or 4 times. The fluid looks pretty good now, not burnt or anything. The truck has been sitting in the garage a lot over the past 2 years, I drive it at least once a month and have put maybe 2000 miles on it this year. It shifts fine through the other gears, just 2-3 has an issue. Truck has the towing package.
View 6 Replies
My 94 F150 has been actingup lately with the 4r70 transmission not shifting into 3rd gear or above. I replaced the MLPS sensor and re pinned the plug as per the instructions with the switch.The old sensor had the plug on the side, same type of plug, but wires indifferent spots. Truck wouldn't start like that, so repinned to match the instructions. I couldn't get the neutral mark to 100% line up as there is not enough adjustment, but it is very close.
The old plug had
32-298-140-33
57-199-359-463
I switched it to
57-359-199-463
33-140-298-32
Then tried
463-359-199-57
33-140-298-32
Truck still won't shift to 3rd, overdrive off button doesn't light up and itwon't start in neutral. I tested the ground at the connector and it lights up atest light connected to the pos bat cable with no issues.
Back up lights won't work, but flicker as going from R to N, so I suspect that is due to the fact I couldn't get the marks to line up 100%, but i'm not worried about that now.
View 1 Replies
1986 F150 3spd Auto 300 v6. My truck will not shift out of 1st in Drive, to shift into second I have to column shift to 2nd. 20mph top speed and idk what to do to fix it. I would like to put a 5 spd manual in it cause I would like to drive over 50mph.
View 4 Replies
So have an '04 F150, 5.4l truck in the shop that has a nice clunk or bang when you tip into the throttle and the TC unlocks. Smooth as glass when you back out of it and the TCC locks back up, no shudder on lockup, nothing. No codes in the PCM, no nothing. Drives well, fuel trims are good. Truck has about 178k on it. Acts like it has an idle misfire, but you don't see it anywhere in the fuel trims or misfire data or anything else. Should I just put a converter in it? Or maybe reprogram the PCM first?
View 14 Replies
I have a 02 f150 4x4 5.4 135 k the transmission will not shift into drive unless you rev it up to about 1500 rpm and when it shifts it goes in very hard but when you get moving it seems to work ok but every time you stop or slow way down it does the same thing. It works fine in reverse and the oil and filter is good. I am thinking TC but i dont know ...
View 3 Replies
1996, f150, 300, 4x4, 5 speed, 296,000 miles... My pedal goes almost to the floor before the clutch engages and about a half inch, maby less, of travel back out the clutch disengages. I think it is about time for a new clutch. My question is what is the best clutch to put in my truck?
while i have the transmission slid back to replace the clutch i am planning on replacing the slave cylinder while im in there as well. Any particular brand better than the next on that item? Are there any other items that I should think about replacing while i have the transmission slid back to do the clutch?
View 4 Replies
i have a 96 f150 xlt 6 cyc. with auto, about 4 months ago we drove 150 miles where the engine overheated and transmission fluid started pouring out from bottom where dust cover is. when got home i filled up transmission with fluid and been good ever since with no leaks. yesterday went 70 miles and did good going down but on way back same thing, engine overheats then out comes the transmission fluid. this morning i filled it up and ran the truck and no fluid leak, what is going on with that.
View 6 Replies
I posted earlier this month about my 1996 Ford F150 4x4 manual tranny truck. It had gotten stuck in fourth gear, and I, along with others, assumed it was the shift forks. I cracked open the top of the transmission yesterday, and what do I see? Melted plastic staring back at me. What's going on here? There was melted plastic jammed between fourth gear and the inner wall.
Is this a case of the surgeon leaving his instruments inside the patient? Could a mechanic have dropped his tuna sandwich wrapper in the transmission at some time?
View 8 Replies
1996 F150 4x4 with 300/6 and M5OD mazda tranny. 145k miles on it and looking really clean, and just the truck we wanted. It used to be well cared for, but has been a bit neglected since the owner passed away.
I spent a few hours searching the forums here and didn't find anything matching my symptoms exactly so I thought I would just jump in a post, but if I missed a thread feel free to redirect me.
I've got a bit of a rattling noise as the clutch engages when taking off in first. Once the clutch is fully engaged it's quiet and it shifts well and smooth. Noise also occurs (but less so) if I don't match RPM's and ride the clutch into second or third. I don't think its engine noise from lugging or anything because it goes away as soon as the clutch is fully engaged or disengaged.
Changed the trans fluid last night and no different, Clutch fluid reservoir is full, clutch travel feels good, master cylinder looks good, (slave is hidden, but looks dry though dust cover) a little play in the white bushing that holds the clutch pedal bar in place, and the plastic pushrod that goes into the firewall, thinking about replacing this linkage.
I work on big diesels for a living so i'm not scared of getting greasy. I'm almost inclined to think someone did a clutch job without resurfacing the flywheel. Is there an improved replacement for the pedal bracket and linkage? I don't mind just doing the clutch, but I don't want to be throwing my money away.
View 4 Replies
Why does my C6 shift at 4000 RPM when the throttle is open? My motor produces peak torque at 5000 RPM, and peak HP at 6500 RPM.
I would like to have the lower gear until I exceed the peak torque at least.
View 11 Replies
The C6 in my truck is acting odd.. its into drive by 17 to 21mph under light throttle and under moderate throttle it slips occasionally when shifting, the 460 had a fuel spurting motorcraft on it, had to swap that for an edelbrock 1406 to drive it. The kickdown is there but setup for another truck. I don't know if the c6 has a vacume modulator or if its all controlled through the kickdown rod.. it does need a fluid an filter change that's gonna happen this week.. this trans just has me leery with the soft shifts.. its in 2nd almost immediately after takeoff....
View 6 Replies
This is an Auto/4z4/4.6 V-8. It's Skidding or a Clutch is not holding at times when shifting up or down while on Cruise and slight hills.
someone suggested changing oil and filter about two years ago. I did that and it didn't change a thing. $145 that time.
I'd like to know if its the clutch in the torque converter, or the Transmission? If I have to change something out, should I get both?
View 3 Replies
So here in Wisconsin for the last two weeks we have had nothing but ice. That being said, I have a '96 ranger 3.0L, automatic transmission, 4x4. 4 wheel is inoperable at the moment, that's a different story. Here's my question: with the ice, there has been a lot of tire spinning at high RPM's, the other day, I was again stuck on the ice and rocked back and forth had some pushers, thought we were getting somewhere but I went to shift gears and all of a sudden had nothing. No Reverse, Drive, OD, L, 2. Did I blow my tranny? There was no noise or grinding, but the OD light seems to blink. Is there something I can check or look at?
View 4 Replies
2011 Focus 2.0L L4 engine, manual transmission, 70K miles - when up-shifting gears, the throttle remains high, dropping v-e-r-y slowly instead of dropping rapidly when the throttle is released. It is the same when not moving, when the throttle is run up to steady RPM's, then the pedal is released, the RPM's drop slowly. This has started recently, at first I thought it was just 'operator error', and that our shifting skills were deteriorating with age (ours, not the car), but testing has proven the fault lies with the vehicle. I researched sticking throttle issues, and thought I had located the problem as a bad throttle body assembly. Changed it out with a new one, went thru the computer reset procedure,and the problem still exists. No error codes are showing, but the little yellow wrench light is lit on the dash (resets each startup. Vehicle drives fine otherwise, no loss of power, etc.
View 10 Replies
My R is vibrating in second gear near full or full throttle around 2,000 Rpm. It feels like a high frequency vibration. It seems to be only happening in that scenario. It's when the turbo spools up and there is a large rush of exhaust gas produced very quickly. My guess is that my apr downpipe paired to the stock cat back is the culprit. It didn't happen when I first put the downpipe on, but after the next track day it started. I don't know if there is anything to burn in inside the apr downpipe but it got louder too. Could it be back pressure from the stock cat back? It's very strange and I wondered if it is stage 2+ but running the stock cat back has felt this? I checked to see if the drive shaft was rubbing on anything and for any other visual indicators of rubbing around the downpipe and I see nothing. Perhaps it's the stock muffler. I'm just not sure.
View 13 Replies
2002 Ranger XLT 4WD 4.0.. I was passing another car at about 55 when they also started speeding up (go figure) so I floored it and got on around them but before I lifted I felt it miss, the CEL began flashing so I slowed to the speed limit and went on to work. The light flashed for about a mile then went out. So on the way home I floored it again close to home and the CEL came on again. Got home and put the code reader on it and all it had was a random misfire so I have cleared it. The truck has new plugs, wires, etc for a complete tune-up. I don't usually run at full throttle so don't know if that would be normal for the Ranger, the Ranger was my wife's truck for 12 years and now is my DD. Need to clear this up? Thought of changing the fuel filter in that is still the original one.
View 8 Replies
Any turbulence in the exhaust note, ie. slapping noise at full throttle. I have run 3 different mufflers in one year on my true dual and also gutted the cats. I currently have 2 1/2inch true dual with gutted cats and cherry bomb extreme mufflers. I Also am running an H-pipe, but I feel it isn't doing its job so well to balance the two sides. My trucks exhaust is almost perfect, it starts mean and loud, and has limited drone at highway speeds and great flow and power, but when I am smashing down the throttle the exhaust goes everywhere and makes all sorts of weird noise.
I almost feel that I should of went 3 inch to allow for me air to get out of the motor, I think the 2.5inch is restrictive possibly hence the air is having a tough time squeezing out of the system. But anyway do you think if i ran an X pipe it would work? Its my last option because otherwise i may convert back to the a single 3 inch dual 2.5inch outlet again, i miss my old set ups mean consistent tone at full throttle.
View 12 Replies
My neighbor's kids truck battery drains from full charge to "no start" in 1-2 days. 1999 Ford F-150 w/ 4.6L engine. He has already.....
1) Replaced the Battery.
2) Replaced the GEM module.
3) Replaced the Turn Signal Relay.
He did all this before I looked at it....
I checked the following....
1) Truck off, doors closed, hood open... Amp meter shows 3.6 amp draw. When 1st hooked up, shows 4.2 amps... after a while drops to 3.6.
2) To isolate the draw, we pulled fuses while checking current draw at battery.
a) Under Dash fuse Panel. (Yes, with door closed) We remove fuse #15 "stop lamp switch, speed control, brake shift interlock, ABS, PCM,GEM, RABS test connector". (Really... couldn't be more stuff?)
b)Under the hood is another fuse box (drivers side). We remove Fuse #103. "Junction Block Battery Feed".
3) Found that if we remove the #15 fuse under the dash with the door opens, all interior lights flash on/off at about 1 second intervals... weird.
4) Again, another weird one... with the fuse #15 removed and door closed, the "ABS" indicator and some other indicators and dash lights are staying partially lit... not fully lit.
5) The only "aftermarket" stuff i can see is a dealer installed trailer brake system. Wiring looks professional and disconnecting it does not remove the amperage drain.
I'm hoping that one of you wizards will give me the "slam dunk"... if this happens, it must be that. Can I be so lucky? And, yes. I have my own '06 F-150 that i absolutely love. 6-cyl., manual trans, stripped down without even power door locks... my kinda technology.
View 8 Replies
So I started to NM from fort worth texas with my 33" camper blew my CAC pipe four times. Finally got there. In the morning it took longer than expected to start. When it did white smoke. That was replaced with black smoke under full throttle.
I went from elevation of 700 to 8000 Ft. Should I care about black smoke? Meaning should I take it to Ford and get a rental car to get it looked at for our trip home.
96 degrees towing at 70mph with lots of climbing mountains.
View 14 Replies
