Ford Transmission :: 1991 F250 - E4od Goes Forward In All Gears
Dec 5, 2009
I am looking at buying a 91 f250 4x4 with a 5.0 and an e4od. When I start the truck I can feel It roll forward A little bit. I can put the trans In od or nuetral and It will drive and shift normally thru all 4 gears, no slipping and no noise no vibration, It shifts and acts perfectly normal. 1st and 2nd work fine as well. When I put it in reverse It rolls forward slightly then drops Into reverse, it will not actually back up, you can rev the engine to stall speed but no higher. Sometimes in park If you rev the engine It will actually over come the parking pawl and roll forward.
Also when In park I can rev the engine to stall speed only. It only starts in p or n, and the reverse lights come on in R so Im assuming the mlps is adjusted properly and the manual protion is adjusted properly. I pulled codes and had 3 in total, ect shorted, egr flow insufficient, and 1 code for torque convertor clutch solenoid I believe It was 632. Im assuming the reving up to stall speed Is related to the tc code. The fluid level Is fine but is a little dark In color, I tried doing a search with no luck ..
View 5 Replies
Advertisement
I have a 95 F250 with 7.5 and E4OD. I was towing my Jeep and trailer out for the weekend a few months back (its been parked since) and heard some noise coming from the trailer. So at a stop light I put it in park with the engine running for a second, went to put it back into drive and it hasn't gone back into drive since. Reverse works perfectly. Fortunately I was able to back up onto the center divide, unload my Jeep and back the truck onto the trailer and tow home with my buddies Chevy. Anyways, its been dead since. Where I can start to look? None of the forward gears work at all.
View 13 Replies
The 91 bonneville stopped having forward gears but was drove back in reverse about 4 miles, reverse appears to work fine does this thing need new transmission or is there an easier fix...
View 7 Replies
I recently bought a decent looking 1999 f250 4x4 5.4 auto. It has no forward gears and will only move in reverse. I topped off the fluids and have found no leaks so far the cooler lines are crusty but dry. I am gonna need to swap this thing out or do some more trouble shooting if there may be a non rebuild issue to solve.
View 4 Replies
I have been hoping this problem would go away but it hasn't. I drive a 1991 350 diesel with Banks turbo and transmission module. When we first bought the truck it was only a few thousand miles before we had to have the tranny rebuilt. It was fine for about a year or two when we installed the Banks turbo and then after about five thousand miles the torque converter flew apart and ruined everything inside the tranny.
After this second rebuild it seems to be doing pretty good all except for it wanting to shift in and out of overdrive for no reason. I can have the cruise set on anywhere from 50-65 and when I start up a VERY slight hill it will downshift to third. I know that this engine has plenty of torque to maintain its speed up these small hills without downshifting so something isn't right. On this last rebuild our mechanic contacted Banks about the trans command and they told him to wrap the exhaust pipe with insulation to keep some of the heat off of the module under there and that seemed to work some.
(It shifts better than at first except for going in and out). Another thing that might be interesting is when it was first rebuilt this last time it had a problem with jerky shifts and the tranny light would come on. Our mechanic had to replace some sort of sensor in the tranny that kept breaking. He did this about three times and since he wrapped the exhaust it hasn't happened again. I hope I made everything clear for everyone to understand.
View 14 Replies
The trans in my motor home has made a growling or slight grinding metallic noise after it shifts into 3rd gear. It only does it for maybe 3 seconds and it doesn't seem to affect the operation. Only way I can describe it is that it grinds, and shudders then goes away. I have towed my race car all this year and it has not caused any issues at all. I am planning on driving out west next year and would like to figure out what the deal is before I hit the road. Also if a rebuild was in order what improvements can be made during a rebuild?
View 1 Replies
I bought a '93 F150 4x4 this past Sunday. It has the 5.8 and E4OD. Yesterday when I started it up and drove to the tire shop for some wheel balancing, it shifted VERY hard with each shift, so hard that it concerned me. I know very little about transmissions in general, and this one specifically, aside from it being electronically controlled.
This afternoon, I drove it again and it seemed to be shifting more "normally" without shifting anywhere nearly as hard as it did yesterday. What I should check first? I bought a filter kit and will change the filter/fluid (including torque converter) as soon as I'm able.
View 3 Replies
My 1990 F-250 with the 460 overheats when driving in overdrive. Driving a hundred miles will turn the trans fluid brown and the transmission is very hot even though it drives just fine. If I drive it out of overdrive I have no problems at all.
It all works fine except the overheating in overdrive, no flashing on the overdrive light. The tans shop is not getting a code, they tell me they have to rebuild the tranny.
View 14 Replies
I have a 1991 F-250 Supercab with the 7.3 L Diesel and twin fuel tanks.Recently the gauge sender for the forward tank stopped working. Ford tells me that the sending unit is obsolete. Perhaps they want me to buy a new truck. I recently found a NOS sender on E-bay but it is supposedly for the plastic fuel tank and mine is the steel tank. What steps would I need to take to make this sender work in my truck? Do I need to eliminate a ground wire, add aground wire, or make up insulators to prevent the sender shorting out on the steel tank?
View 2 Replies
I have a 98 expedition with a 4.2 liter 4x4 and what I believe to be a 4r70w transmission (u code on the door sticker)
The original transmission went at 105k miles and was replaced with a new factory ford transmission by a ford dealer 3.5 years ago. The new transmission only has 10k miles on it.
Now the new transmission only has reverse. reverse works like normal but no forward gears. the idle will change when i put if in gear, but will not move, acts like it is in N . There is no strange noises.
It's hard to believe a new trany is shot already, no towing, or off road use.
My question is : is there ANYTHING that can go bad that would cause this? The trany fluid is clean and clear bright red, and no burnt smell.
I want to check everything I can before calling a tow truck to have it looked at. I will have it repaired if needed, but I don't think I want to replace another tranny.
View 14 Replies
Had tranny fluid and filter replaced a couple months ago. It's in a 35 foot motorhome (F53 chassis). The motorhome is within it's GCWR. Climbing a 6% grade at 3,500 rpm, little more than half throttle, like all the other climbs. 80 degrees out. Engine temp was on the letter "R" on the word "NORMAL". All of a sudden my engine redlines as if it popped into neutral. I let off, put it into neutral, and try "D" again. Nothing.
At this point it's uphill so it's naturally slowing down and I try "2". Nothing. Even slower and I try "1". Nothing. Pulling over blocking the right lane on a blind curve on a grade is scary. Had pylon cones out, waving traffic to warn them down a ways, etc.
No fluid on the ground, no slipping prior to this. I have reverse. I see no obvious linkage or electrical/wire issues underneath (from road debris, etc). It's at a shop but I want to know all I can so if they come back with something outrageous I can make a decision. I never pulled the stick, as I was coordinating traffic, highway patrol, a tow truck, etc.
View 6 Replies
Alrighty now. I have a 93 f250 idi Na.
Before problems started: the truck.shifted all 4 gears fine.
Problem(s) begins: Then out of the blue(after I shut it off... even if it was for 30sec, and then turn it on ) it would go into limp mode but if I shut it off and then turn it on again, it would work fine. After about 3weeks/ 600 miles it just went straight to limp mode.
What I did: After 3-4 weeks of that, I replaced the solenoid pack(uncooked both batteries and waited 10 min before I hooked them up) with a eBay special. After that, I had 1st,....., limp 3rd, then it'd slam like check into OD. To get second(which was limp), I'd have to manually drop it in 2 and and let off the pedal before I'd put it in D, to avoid it slamming straight into OD. It would toy with limp and OD from 35mph-45mph. Then it.just went straight to limp mode again.
What I couldn't do because don't know how to solve: I went to go get the codes read and the connector was missing and only one wire was leading to where the connector should've been.
What I did...again: I replaced the control module in the firewall. Then my codes cleared up. And same problem as when I put the new solenoid pack in. But no codes.
What is it still doing????: it's a go round battle between complete limp mode, limp mode and wanting to go into gear(suited to proper mph&rpm), or 1st, limp2&3, and OD.
What I tried: TC lock-up switch.,. And it worked but didn't solve my problem so I scratched that one.
View 9 Replies
I have a 1991 bronco with a 351w and the e4od trans.. The transmission is shifting late and hard and sometimes when i let off of the gas to slow down it shifts between gears up and down by itself... The only lights on the dash that are on is the Rear Anti-lock brake light and the speedometer is not working either.. Where to start the trouble shooting to fix it?
View 3 Replies
I have a 1997 Mercury Mountaineer with a 4R70W trans behind a 5.0 liter. Vehicle sat for about 5 months. Went out to put it back on the road, and now the trans seems to be stuck in a forward gear no matter what the selector is in, park, reverse, neutral. Dropped the pan and replaced the filter and replaced what fluid was drained. no difference,.
View 3 Replies
The truck is a 2002 f150 4x4 5.4l... I was driving down the free way last night in 2wd doing about 90kpm when there was a loud bang like a ran over something. Speedo went to zero and abs light came on. Pulled over and shut it down. Crawled underneath to check so damage and couldn't see anything. Stared it back up put it in drive and it just revs. No forward gears or reverse. Fluid level is good, bright pink. Dropped the transmission pan, pan is clean and magnet has next to nothing on it.
View 14 Replies
I have a F150, 2nd 4.6, 122,000 miles. No forward gears. When put in drive, you can feel it trying to engage, but doesn't engage completely. Reverse is a solid engagement. Replaced filter and fluid, same issue.
View 12 Replies
2003 Explorer with a slipping transmission...codes are P0731, P0732, P0733... Just had a new solenoid pack installed last week when O/D light came on and truck was clunking into reverse. Now, after new pack was installed the forward gears are slipping all over the place!
View 5 Replies
I have a 1999 F-250 4X4 7.3 lit Diesel engine. My problem is my transmission will go into reverse great no problem but it won't go forward. I have no problem rebuilding the transmission if that's what it needs, I just want to make sure there isn't a electrical issue from the PCM first?
View 14 Replies
2006 f150 4x4 4R75E trans slipping in forward gears, reverse is ok. I dropped pan and it was clean. I dropped valve body and found OD servo shaft clip broken, the large snapring was I fine and in place. It allowed the inner shaft to float up and down. Would this cause my forward gears to slip or do I have a bigger problem?
View 14 Replies
The other day I was leaving my house. I started the car and heard a quick, loud chirp. That was the only noise it made so I continued to leave. I rolled out of my driveway and proceeded to put it in drive and found myself rolling backwards. I tried every forward shift, kicked on the 4x4 and continued to roll backwards. I thought reverse worked but found that it wasn't engaging either. My question: is there anything I can look at before resorting to taking it to the tranny shop? I'm in school for automotive and am confident in my abilities to test solenoids and maybe even dropping the valve body to check that. Other than that, I lack the skill to pull the tranny myself and work on it.
View 3 Replies
My 1999 7.3l Disel 4x4 transmission quit on me the other day. No forward or reverse. Got towed to my regular repair shop, and they are treating the transmission as a black box and recommending total replacement. The diagnostics they performed were to make sure it was shifting, and that indeed it wasn't going forward or reverse. They drained the fluid and said "it's pitch black" and said it had to be completely replaced.
Fluid level was OK, and it wasn't hot. I was driving along, and merging onto the highway. It downshifted, shuddred, and nadda. Free rev. I coasted to the next exit and into a parking lot. Verified that it was shifting, checked Rev and all forwards. It wouldn't shift into 4W, and 1-2 also wouldn't move.
I'm trying to figure out what might have happened... and if it's worth trying to have the truck towed to a transmission shop and have them diagnose and rebuild, vs just getting a remanufactured transmission. None of the local wreckers have any used transmissions, and the cost between a reman and a used is pretty negligible...
Not sure what the symptoms points to for exact failure mode, be it the torque converter, pump, input shaft, etc... I've never had an automatic transmission apart before, but built plenty of motors and am a machinist by trade. My preference is to try and root cause the failure...
View 1 Replies
