Ford Transmission :: 1989 - Revving Up Real High Before It Went Into 2nd
Apr 5, 2008
I have a 89 f250 4x4 351W FI C6 Auto, recently I was having problems with the trans it was revving up real high before it went into 2nd. I dropped the pan and the valve body to make sure their were no shavings or any other debris. Everything ok.
So I replaced the valve modulator and the line that goes to the intake, replaced the MLPS and adjusted the intermediate band. I put it all back together and NOW it won't even go in gear. Did I hook up the valve body wrong? If so what is the proper way of doing it?
I only unbolted the valve body from the trans I didn't take it apart. I was also wondering whats up with the color strips on the modulator I have purple right now was i suppose to have different color? Could the pin for the modulator not be in place? I added 3 quarts is that to much or not enough?
View 6 Replies
Advertisement
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
View 6 Replies
1989 Saturn 5 speed, 4 cyl, 185,000 miles. Just started overrevving, when I try to go into 1st or 2nd or idle RPMS jump to 4500. So not a good thing. Do not tell me to buy a new car, not in the budget, or maybe it is.
View 6 Replies
03 F350 7.3PSD... A/C blows cool on max only but does not blow real hard on high.
Blower motor is loud like it is blowing but just not coming out of vents. On reg A/C blows hot, actually blows hot on all other settings.
A/C compressor is on but blows hot through vents. I am thinking blend door and or something else. Thing is I am not sure what or where to look and how do I check?
View 1 Replies
I bought this truck for work and all of a sudden it will rev real high when I press the clutch in to switch gears or when sitting at a light. I stopped at a parking lot and popped the hood and tried to pull the throttle back by hand but it will not go. There is a lil slack in the throttle cable but when the truck is off and I manually pull the throttle back it returns normally.
I was wondering if the little black electronic box opposite where the throttle hooks to the throttle body is making it rev so high? I really don't know a lot about these newer trucks as I have driving older trucks my whole life so probably using wrong terms...
View 12 Replies
My '89 Ford Crown Victoria Country Squire is a 5.0L with the AOD transmission. Yesterday, I slowed from 40 mph to 25 mph to turn on my street. As I drove up the street's slight incline I noticed the acceleration was sluggish as if the transmission had not downshifted from 4th to 3rd. When I stopped to back into my driveway, the engine shuddered and stalled as if it was hooked to a manual transmission and I had released the clutch with the shifter in an upper gear. My wife had to push the car into the driveway (she is a Minnesota farm girl ).
Now the engine starts normally with the gear selector in Neutral. It shudders and stalls the moment I try to put it in any gear or Park. The engine will not start in Park, but once again, balks as if I was trying to start a manual transmission equipped car without depressing the clutch or taking it out of gear.
The transmission and engine had been working perfectly before the above sudden problems. My guess is that the transmission is somehow stuck in overdrive.
Is there any way to knock it out of 4th gear? Why would the engine start in Neutral but not Park? It is the original AOD transmission with over 230K miles on it, but this car has at least nine lives and I am hoping this is another serious problem that turns out to be not so serious!
View 7 Replies
I drove our 95 3.0l aero to work today, I was going to a job 45 miles away. It sounded like it was revving awfully high for 65-70mph, but the gear selecter said od, so I figured I was just crazy. Got to the job and tried to back up and the shifter wouldn't go into reverse. Parked for the day after realizing the shifter would go N and down, but not into rev or park. Apparently it was revving high, as the gear indicator was now off and I was no doubt in drive, driving to work. I got it home, then had to drop my daughter at work, by staying in OD.
Then on the way home the van just DIES while going 35+- mph. Won't restart, smelled gas after many many attempts to start. Towed home. NO spark. I have 12+ volts at+coil. I tried my ignition module and a new one, neither sparked at the coil wire. I bought a new coil, then checked resistance at + &-, and - and coil output post. Basically same resistance new & old coil. Did my hall effects or cam, or crank sensor just go out or? Why both problems same day? I thought if it was the coil or ignition module, maybe it got too warm on drive revving high. Does a 95 3.0 coil get triggered by the distrib haal effects or does the crank sensor do it?
I can easily see one of those being bad as they are original, with 334,000+ miles. All the tune up, coil, wires, plugs, ign module, cap, rotor, were replaced 55,000 miles ago. ALSO does this distrib have a TFI module on it? My book says to pull the distrib and remove it, like my 5.0l Mustang, but I don't see one, I think thats the ignition module on the pass. inner fender. I'd like to see if I can get 400,000 miles out of it.
View 4 Replies
My ranger sounds like it's revving up real high when I take off but don't have much power. Know what this could be?
View 5 Replies
We are planning on taking our 07 Explorer in to the dealer to have them check on a couple of issues. 4.0 with auto and about 45,000 miles on the ody.
1. While taking off after waiting at a stop light or slow speed traffic crawling there is a high revving sound coming from the engine compartment. Sounds like the fan is over revving compared to the engine speed.
2. Recently the truck has a hard time going into reverse. Physically hard to move the gear select lever and there is a hard "thunk" when it does actually shift into reverse.
I just want to be armed with information before heading to the dealer. The truck is still under a warranty plan, I just need to be prepared. Could it have to do with the Transmission Range/Position Sensor?
View 2 Replies
I'm trying to add some 134 to the AC to see if it will work at all. it slowly stopped last year. I got a charge hose and a can of just 134a. When I attached the hose the gauge pegs on the high pressure side. I know I'm on the low pressure side and the compressor isn't running. It starts and stops. Should the pressure be that high with the compressor not running?
View 2 Replies
6.0L revving to extreme high RPMs and kill? Blow turbo was replace, fired right up but upon pulling it out while giving it lower RPMS (2000) engine over revved and killed - Now crank but no start. Checked everything. Removed valve covers, checked injectors, great fuel pressure.
View 14 Replies
Have an 89 F150 WITH 5.0 AOD TRANNY has a hard shutter from 1st to 2nd and shutters hard under low rpm I am Second also shifts rough all the way through and in to od and reverse was wondering what's the possible pro lens and how to fix them....
View 2 Replies
Its a good runner. It has lots of get-up-N-go until you get to 45-mph. Then it just loses interest.
It's a 1983 Ford F-150 King Cab Short Box with a 302? V8, a 5 speed manual transmission, 2 wheel drive & a heavy towing package complete with low speed rear end, over-load springs & a 800 tongue Weight rear bumper. It has about 116,000 miles (long haul miles) on it.
The previous owner said it had had this problem before, and new spark plugs fixed it. I don't know, but it seems more like a fuel or vacuum problem. It behaves just like one of those rental truck governors. Plenty of power up to a preset RPM, then blah.
A mechanic I know said it may be a RPM limit switch in the transmission that prevents over revving the engine. Is he talking straight?
View 11 Replies
finding out what is wrong with my Taurus. I have searched all over the internet not finding any posts about a similar problem. When driving after I turn past a certain point only to the left not to the right. The car slips into neutral revving, then once Ive straitened out somewhere along the wheel turning radius it re-engages in gear and lurches forward. The car drives fine and shifts smoothly except this.
View 3 Replies
Recently, when I start my Golf 2.5 DSG it has been revving a little loud or rough. It usually revs at under 1k at idle, but when starting up it revs at around 1500 until I put it in drive and release the footbrake.
View 10 Replies
I have a 1989 ford f150 xlt lariat it has a 5.0 and a 5 speed and is 4 wheel drive. Any way I am looking into rebuilding the rear end of the truck the pinion shaft has a lot of play in it up and down and both outer axle bearings seem to have lots of play in them. I believe it is a 8.8 inch in the rear. Just wondering if there hard to rebuild or what it all entails I have never taken one apart before and want to know what I am getting into. I have access to a press and a pinion and carrier bearing puller. the axle bearings i have done tons of them but never had to pull out the carrier. wondering how to set turning torque and backlash etc... and torque specs for everything.
View 8 Replies
I have a 1989 tioga 460ford and the trans appears to be slipping when i get around 50mph. The engine revs up but it won't go more than 50. The engine again revs up but there does not feel like the power of the engine is being transferred to the trans. the coach runs fine up until i try to go beyond 50. I have 34000 miles on the rig. Some one suggested that I check the catalytic converter. what else should i look for?
View 2 Replies
I got this 89 ranger xlt with a 2.9 and automatic transmission. I mainly bought it because it was in such good shape and I was planning on putting a 5.0 in it. everything works on it. the a/c, radio, lights and it runs real nice. the only problem it has is it shifts pretty hard going into second gear. every once in a while it will shift smoothly into second but only like once or twice a day. he said he had recently changed the trans filter and fluid and the fluid does not smell burnt.
View 7 Replies
I've been dealing with this for over a year. 97 s-10 (4.3, 4wd, 5spd) always wants to keep revving. When I put it in neutral and coast, the rpms rise. When in gear, it powers itself down the road even when I'm off the gas. The part that really gets me, is that it will keep revving in neutral until the vehicle comes to a COMPLETE STOP. Then, it drops to a nice idle within 2-3 seconds. I don't understand what the momentum of the vehicle has to with the revving of the engine when its in neutral.? I replaced the IAC valve (and set the pintle) and tried to clean up everything I could. It seemed to be better for only a little while. Faulty new part? Is the IAC getting "gummed up" quickly because of something else?
View 3 Replies
I have a 2007 Passat with >120k miles on it. For the last month or so, occasionally when I start the car up, the EPC (I think it stands for Electronic Power Control) light and the Check Engine (the engine sign) light comes on. When I hit the gas, it barely goes past 20 and seems to be revving really high (almost redlining) before it finally accelerates. Needless to say, this is not a good thing; especially when it happens on the freeway.
I called around to a few mechanics but they all want to see the car and run the computer codes on it before they even tell me what's wrong with it; which I am loathe to do just yet because I don't want them to charge me an extra $100 for a diagnostic for a repair I may not even get done with that mechanic. Meanwhile I'm driving around feeling like I should put my feet on the ground like Fred Flintstone to gain speed.
In the research I've done online, I've seen that it may be an issue with the throttle wire or some other wiring issue.
View 1 Replies
I had some problems with my Elantra and I fixed (or tried to) them all this weekend. I needed a new IAC motor, the motor was reving up and down and I tested it, then changed it. I needed a fuel injector and changed that. I needed a lower thermostat housing and changed that.
These changes resulted in the following problems. The vehicle now revs at a high idle all the time at approximately 3000. What are the causes of this?
I know that when I was burping the coolant system (changing out all the hoses and the thermostat housing) I got antifreeze sprayed all over the top of the motor.
Here is the problems that I have now. Didn't have these before.....
The engine idles at or about 3000 rpm. Constant from startup until shutdown. It idles down when you shift it into gear but that is because of the strain on the motor with the brake used.
The transmission is now having problems shifting from 1st to 2nd. I checked the fluid, its good. There is however antifreeze on top of the transmission by some sensors. Do these sensors have anything to do with the shifting?
View 11 Replies
