Ford Transmission :: 1989 F350 - Harder To Shift / Grinding Noise Like It Doesn't Want To Go In Gear
Jan 15, 2014
I have a 1989 F-350 7.3 IDI with a ZF-5 trans. Lately, I noticed that it was a little harder to shift my truck through gears while driving than it normally is, and when I'm stopped and try shifting into first gear or something it like vibrates and makes like a grinding noise like it doesn't want to go in gear. For a while, I've also had to push on the clutch very hard in order for it to I guess hit the linkage and start, but I never had problems shifting until lately.
Today though, I went to start my truck, I pushed on the clutch as hard as I could, and the switch would not engage so I couldn't start it. So, I guess the switch was farther to link than the pedal could possibly go. I went under the dashboard and engaged it by hand then it started. I drove home and the shifting was still iffy. How can I make the switch engage normally again so its closer I guess and so I don't have to push so damn hard on the clutch to get it to start? And could the switch linkage have anything to do with the shifting being funky lately, or could that only be the clutch itself?
View 3 Replies
Advertisement
I have a f1ta 5 speed trans on my 4.9 and when i press the clutch in and shift into 1st gear it makes a grinding noise then goes into gear after a little patience. but if i press the clutch and wait a few seconds, then shift into 1st its fine and goes right in.... maybe syncronizers not meshing or they're worn? or could it possibly be a low fluid prob? idk, it just started happening.
View 3 Replies
I bought this truck with 60,000 miles and have had about 3 months. I don't drive it very much but when I do I have noticed that when it sets for 4-5 days or longer the transmission makes a weird noise as you take off and does does shift into gear as it does when I use it ever day. The problem goes away very quickly (not even a 1/4 mile driving) and everything is fine after that. By the way I took it to the ford dealer who did a complete 60,000 mile service on it that was suppose to include changing the transmission fluid and filters-could they have screwed something up (I did not notice this issue until after the 60,000 mile service?).
View 7 Replies
My 2007 es350 is already warmed up, so I know its not a temp issue.
My VSC light comes on (i know it comes on with any DTC)
My traction control light is on
My engine light is on
Now, when driving, it doesnt shift out of first gear till about 4K rpm and thats at normal acceleration (not flooring it) and shifts out of range on all other gears.
I can hear a humming/winding noise coming from the left side of the car (tray side) and it does it and I can hear it very clearly when letting off the accelerator (more noticeable at high speeds)
View 5 Replies
Recently I have another problem:
When I drive uphill on the way the car's transmission doesn't shift up to the upper gear,the gear stays on 1,when I press the gas pedal more the EPC light comes on the dashboard,I must release 2-3 times the gas pedal then the gear goes up to 2-nd or 3-rd gear.This happens only when I drive uphill,when drive on flat street this problem almost doesn't come.
Another,when I drive downhill,the gear doesn't release sometimes too,the car tries to stop from 3-rd gear directly to 0,and the RPM goes straight to 100-200,even the car turns off... I heard something for the VW Phaeton transmission problems,and that it can be SOFTWARE flashed and the problems go away???
View 2 Replies
Have a question when I shift slow from 2nd to 3rd my o2j tranny doesn't grind but when I shift fast from 2nd to 3rd it grinds it happens starting at 3000 Rpms thru 6000 Rpms. It also doesn't happen when I shift from 4th to 3rd. Have performed a tranny fluid change. Along with replacing the clutch at 1500 miles ago. The engine is AWP.
View 4 Replies
My camry has been great up until the last week. The weather has gotten extremely cold here and when I start driving in the morning or from any cold starts the transmission doesn't shift out of second gear. After I drive it a mile or so and slow almost to a stop it will shift normally until I park it.
It has 125000 miles on it and I hope this isn't a serious problem because it is a great car and has been well taken care of. Looks brand new on the inside and out and I've never had any problems until now.
View 3 Replies
So I picked up a 20th today. The clutch has 30k on it its an oem luk. Drove fine most of the ride home then i went to shift and it wouldn't grab. Got it towed home. trans goes into all gears fine. When you put it in first and try to go it starts to roll but just makes a grinding type noise and doesnt go into gear. I didn't hear any chatter until maybe 10 miles before this happened. I still have pressure in the clutch pedal as well. when the car is in neutral running there isnt any noise which makes me think it isnt the throw out bearing.
View 2 Replies
I am now getting a grinding noise when I shift from first to second gear. It sounds like the two metals rubbing each other. Its not happening all the time, but for the past two days a bit frequently
I had reported this grinding noise when I turn left a month back. Was thinking because of my worn out tyres, but apparently not.
View 8 Replies
I have an early 99 F250 4x4 7.3L..... 4R100....
Brief history, a while back on way home from work I let off of the accelerator and had a loud gear meshing like grinding noise, got back on the accelerator and went away, let off and back, so I quickly stopped and pulled over, went through the gears and reverse, everything seemed ok,??? went on my way, got home parked the truck and went about my evening. came out next day to leave and truck wouldn't move in reverse, forward but not reverse. long story short I was told that the snap ring internally probably came out, I have heard of this being a big issue with these, so I set up for it to be rebuilt, got it back and installed and still same issue, what the crap so I ended up having to pull it back out and amongst my own trouble shooting I found the simple issue and was the nylon riders on the 4hi/4low shifter fork were completely gone and allowing the planetary group to free float in and out of 4x4 neutral!!! NOW on to the issue at hand. so far only thing has been done is rebuilt and those fork riders replaced.
now I can move but 2-3 upshift under a load(more noticeable) has a delay going from 2nd to 3rd and under a load it hits hard. I talked to the guy that rebuilt it and he said that the rebuild kits don't always the right springs for the valve body and causes shift issues, so he talked me into the shift corrector kit which I researched and did see what he was saying, so had that done and still no better, still does it, however, it does shift into the gear softer but didn't fix the delay or the hitting hard when it did finally go into 3rd.
After being forced to drive it that way I have since determined that what it happening is it is coming out of 2nd with a second and half pause and then shifting into 3rd, the hard shift comes in to play because during the delay the torque convertor is locking up making it a direct drive like popping the clutch on a standard!!!
I just swapped out the sol pack and I heard from a youtube video that the bolt next to the 2-3 upshift valve on the valve body could be to tight and making a sticky valve, so I re-torqued all the bolts and nuts put all back together and test drive proved to be worse, I now have same issue in all upshifts. all hit hard now, I am at a loss and don't know where to go from here, I can only imaging the sol pack is causing this but I have yet put my org one back in to see... oh and I found two bolts on the accumulator stripped and found one non torqued bolt on the main valve body!!
View 2 Replies
I have a 2002 Saturn SL with nearly 170,000 miles on it, but the manual transmission has gone seriously wrong... I was driving today and I noticed that it was progressively getting harder and harder to shift. By the middle of the afternoon I was strong arming it. Yanking it into as well as out of gear. By around early evening I could no longer get it into gear at all. I was at a stop sign when this happened and ended up stuck there. Now here's the weird part: When I shut off the car the shifter would slide right into gear. In fact, it would go into all of the gears no problem. As soon as I started the car back up I couldn't get it into gear. So what ended up happening is that I put the trans in gear then started it and limped it home in 2nd.
View 6 Replies
I have a 89 Ranger, 2.3, 2wd, Mazda 5 spd. Last year, 10,000 miles ago, I replaced the clutch, pressure plate, slave cyl, and pilot bearing. Today, it started making a terrible grinding sound/vibration when you let off the gas. The noise is coming from the clutch/transmission area. It is so bad that any amount of "engine braking" sounds terrible and I have to press the clutch in and the noise immediately stops. What to check for?
The only thing I can think of off the cuff is
1) bad pilot bearing,
2) low/no tranny oil. I replaced the oil and put silicone on the known leaky spots while I had the tranny out,
3) Input shaft had some "wobble" in it when I had the tranny out to replace clutch 10,000 miles ago.
This could be it but why would it start 10k miles later?
View 2 Replies
I have a 98 saab 900 se turbo.90000 miles on it. Just had a new clutch kit/throwout bearing and master cylinder clutch installed, as the clutch was going bad.
When I shift the car (while driving) from 2nd into 3rd/4th/5th gear,and accelerate I suddenly notice what sounds like a "grinding"/raspy noise that stays with the car while in those gears. It does not occur in 1st or 2nd , although it seems that in first gear the rpms go up real fast now (could the gears be slipping again?? this is a brand new clutch..).
The second I shift to 3rd gear and give it gas, the noise shows up instantly. Now when I let my foot off the gas, the noise goes away 100%. The second I give it gas again, it comes back. Also I don't believe the noise increases or decreases in relation to the speed of the vehicle. It seems to stay constant no matter what speed I'm at, as long as I'm actively giving it gas.
It occurs every time I drive..not sure what to do and what causes this..maybe I just need to check the transmission fluid?
View 19 Replies
I hve a 89 Chevy Silverado Z71. Transmission will not shift out. It's only a little over a year old. Got it from Advance Auto Parts.
View 8 Replies
'89 Honda Accord LX Sedan 5-Speed, 266k miles...
Bought this car recently and it worked fine when I got it (the most perfect 22-year old car I've ever seen). Between then and now I've driven it a little. It's my first stick shift car, so I've stalled it a few times, ground the gears a little, etc. learning to drive it. Anyway, it now won't shift into first gear. It shifts fine and drives fine in all the other gears, the only problem is with first. It also shifts fine into all gears when the car is off.
On a side note (in case it pertains to this situation), the car takes a little while to warm up. For 5-10 minutes after it is turned on, it idles really fast and makes a horrid scratching noise and then stalls if put into reverse (don't know about first, since it won't go into first). Once the idling slows down, though, this problem goes away.
View 7 Replies
I have a 2008 Elantra GLS. I am getting a code of P0750. Seloniod A fault. I have checked wiring harness for critter bites all looks good. If I clear the code the transmission shifts normal until it is shut off like overnight. I also have been noticing that it idles around 1100RPM to 1300RPM and it does drop into gear harder (reverse or drive). This high idle started before the P0750 code.
View 4 Replies
I have the mods listed below in my signature. When I shift gear and have almost completely released the clutch to move up into the next gear I get a clicking noise and feel from my transmission I think or maybe differential. This is with traction control off and is only noticeable at lower rpms like a low rpm shift from 1st into second.
View 7 Replies
I replaced the pads and rotors on my 1989 toyota camry yesterday. Took it out for a test drive and all appeared to be OK. I did not bleed the brakes, but did have to remove a small amount of brake fluid after installing everything.
On my way into work this morning there was quite a bit of grinding noise coming from the brakes. The noise was not consistent, happening both while brakes were depressed and also when not in use. It also would go away after a few minutes and didn't always happen while braking.
I'm thinking the piston may be locking up at times, but don't know. I'll also throw out there that this is my first brake job. I did follow my Haynes manual and don't think I did anything wrong.
View 8 Replies
Sold my mazda and got a nice 2000 2wd Ranger XLT with a 3.0L. Today the wife I and took it to town, 10 miles on the highway there, a couple in town and 10 back, didn't notice anything unusual. However I haven't this truck long so I'm not sure what is usual.
Parked it for a few hours and when went out to change the front turn signals to LED I noticed the ABS light was on when I drove it into the garage...
I checked fluid, connections and fuses, no change.I go ahead and swapped the bulbs while letting things simmer, I've had so many of these Fords sometimes the easy fix comes to me.
I backed it out and took it down the road, right away I noticed my speedometer wasn't working, so I let off the gas, when I re-applied the pedal I got nothing, like it was in neutral.
I downshifted to second and got her down and turned around as the O/D started flashing... (so glad because I would have hated walking back), then pulled her back in the garage to check transmission fluid and recheck fuses, including the ones I forgot earlier under the hood. I added a 1/4 qt of fluid then tried a road test again, this time there was a real long pause before it upshifted hard and the CEL came on.
I pulled the codes with my scangauge and got:
P0500
P2120
P0028
And decided I better look some things up and consult the gurus here before I do anymore damage tonight. I'm guessing that I'm looking at a tranny replacement possibly, but with the ABS light and speedometer failure I'm not 100% sure what is going on here...
View 12 Replies
Replaced Troque Converter, Truck runs engine runs fine transmission won't shift out of 1st gear.
View 2 Replies
I have an automatic 1992 940 GL and it has been almost a year since the head gasket blew in the car. The gaskets and everything have been replaced as well as the fuel filter, transmission pulley, and timing belt. The car seems to run fine except for a small problem with the gears. When driving it's like it doesn't want to shift into the next gear unless you let off the gas a little bit which then it shifts over fine and it does this for all for gears. It has also recently started back to stalling out at a stop light or stop sign but very rarely.
View 1 Replies
