Just got my torque app running. At idle I am seeing ect of 186.8 and eot of 176.8. After driving around town for about 30 minutes. Are these acceptable?
Note: ambient temp is 22F
I pulled into my driveway after a 30 minute drive and smelled burning brakes. The right front was the culprit so I took a garden hose and cooled it down. The next day I remove the caliper and one of the pistons fell apart. So I need a new caliper and trying to decide if I buy after market or go with Motorcraft? I think the rotor, caliper, and pads are original since I the rotor is stamped Ford and the caliper bracket has TRW and Ford markings.
View 12 RepliesWhen starting up my 2011 F-250 Gas, I have a burning smell coming from my vents for about a minute then it goes away. It smells like new electronics. My A/C seems extra cold as well. We just got back from a 3800 mile vacation. Its been going on now for about 3 weeks and never changes...
View 6 RepliesI have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesI've been tracking down all sorts of issues in my Excursion 4x4 lately and I have a few questions. I have an issue where everything is spinning as I drive even in 2wd. I gutted my hubs and removed the driveshaft. I had new u joints put in the front shaft today and re installed it. I still have the same issue of everything spinning while driving in 2. I had my marks move with the shaft in or out. I assume its getting toward front axle joint time. The shop owner said there should not be any movement in 2 but every SD I've seen has the axles spinning driving around town. I'm just confused because I have the entire driver side axle move when I spin the shaft by hand.
View 11 RepliesChecked the EOF vacuum lines and pump but still have a problem. The EOF works and locks the hubs when I switch to 4x4 high, Easy to feel when you turn the wheels but it will not go into low. The light on the dash does not light up the word "low".
View 1 RepliesWhen I shift into 4Lo I get no 4 wheel drive. 4Hi works. Did have a/c redirect to defrost a couple of times. I remember something about the air redirecting having something to do with not having 4x4 but don't know just what it was.
View 8 Replies1999, F250, SD, v10, Auto, 4x4.
My light on the overdrive is not coming on and the overdrive does not seem to be working. I had a new transmission installed a few weeks back. Wasn't working prior to this.
Last week the ABS light comes on and will go off after a short drive. Obviously the Scanguage II does not read the code. I have replaced both front hubs last year and have less than 6k miles on them. I have checked the connections, and are good. I changed diff fluids around the same time as the hubs.
View 1 Replieshave a 2006 Forest River Lexington 255 GTS on a Ford E450 chassis. We purchased it used 2yrs ago from a private owner with only 20,000 miles. It had a slight vibration which got worse over 60 mph. All tires were replaced and when that didn't work, took to a different dealer to have road balanced. We drove the home some and the vibration got worse starting about 40 mph. We took it to a local truck repair shop that does drive-line work. They have replaced the transmission tail housing with a bearing it, had the drive shaft rebuilt including new u-joints and re-tubing the front driveshaft. The vibration now is worse than ever..so bad that it's not drive-able over about 30 mph.
View 7 RepliesToday I noticed that our 5R110 was delaying slightly when shifting from drive to reverse. It was probably about a 1-2 second delay but it replicated itself twice in a row. There was no delay going from reverse to drive. It is just an engagement delay. We are running a Superchips Heavy Tow tune on the truck, it is a 2006 6.0 Powerstroke.
View 4 RepliesRecently purchased a 99 F250 SD w/ V-10 Triton which purrs like a kitten and drives great until I turn it off and then re-start. It has trouble re-starting and then when started and put in drive...won't go anywhere. Zero power. Oddly, in reverse it goes. Getting decent flow from exhaust. No vacuum leaks I can find. No check engine light on either. Strange.
View 7 Replies1. Why does my front end hop when only turning right in 4 wheel drive?
2. O nly one of my back tires spin, so does that mean that when I put it in 4 wheel drive I only have 3 tires spinning?
oh I got a 2001 xl 5.4 f250 and is this normal
Not sure what caused it to break but my front driveshaft split in half. I had it in 4wd and was doing a K turn to back in my driveway in a snow storm.
I got underneath in the snow (miserable) and wasn't able to come close to getting it off. The bolts holding the shaft onto the t-case will not budge and the tiny 5/16" bolts stripped all my small 1/4" sockets. I'm guessing I need a 3/8" drive 5/16" for front and the rear just spins. Any tricks to getting this off the truck.
So after eight years my Warn premium hubs have taken a crap and developed major play internally. After speaking to Warn warrenty department and sending videos they will replace them according to the lifetime limited warranty. Problem is they sill not send out new ones until they receive the old ones, so I was told from time i remove mine and send them back and get the new ones it will be two weeks maybe a few days more, there is no snow in the extended forcast and im wondering what damage could occur with me funning the truck everday to work etc with the stub shafts just hanging there?
View 14 RepliesI'm getting a really choppy low RPM drive. If I'm above 2-2.5k rpm it runs okay but as soon as it drops under 2.5k it starts to run very choppy and loses power and Boggs in and out of power regardless of how much throttle input I give it. I had a tune up done last year and a recent oil change...
View 1 RepliesHere's what I have 2000 F350 XLT 105000 miles and a 4R100 tranny, was coming home from work no issues, stopped at my mailbox to retrieve mail.
when applying brake, it lunged forward a bit and stalled, I started back up put in drive, stalled again. started back up put in reverse, no issues.
I put in neutral revved it somewhat and it moved forward enough to start the roll down the small slope at my drive, I then started in neutral again as was rolling and then put into drive and drove 1/2 mile down my lane to house. backed up in my parking spot, no problems then shifted to drive and stalled.
Today I dropped the pan and checked the filter as I have read that sometimes they will fall out and cause same symptoms, filter was where it was supposed to be, no easy cure here.
I just purchased a F250 Gasser with the 6.2. I made sure to get it with the 4.30 rear to babl to tow a little better when i upsize the tires a little. Where I can find the drive output ratio from the transmission?
View 2 RepliesI have a 2001 F350 7.3 4WD that does not want to shift into drive. When you shift to drive you can feel a slight difference in the trans but it will not move, it will rev freely but not move. If I shift it up and down it will engage after a lag period ranging from 10-15 seconds up to several minutes. Reverse is ok and after forward engages it appears to work as it should, shifts ok through the gears. I don't have much experience working on automatics.
View 4 RepliesMy 2009 F-350 4x4 has a front wheel option of Auto or Lock ; I think I understand the Auto option but under what circumstances would I lock the hubs and is it safe to leave them in the Lock mode when traveling on the highway?
View 5 RepliesI have a 2004 F350 with a broken drive shaft.
Got the original shaft off and it has the following part number (2C34-4K145-DNA)
but I've since learned that the part number has changed but the only info I could get was 2???. 4R602DQA.
Trying to find the part number so I can find it under 750.00 from the dealer