I recently checked and changed the one bad ujoint in the rear shaft but I still have a vibration once I hit 35mph but doesnt happen all the time and sometimes goes away while driving.
View 2 Replies01 F350...4R100/V-10/4wd. Sometimes get a vibration driving down the road. First thought of tire out of balance but then the vibration goes away and may not come back for a few days or more. It starts sometimes around 30-40 mph and stays all the way up to around 65 mph. Even slowing down it vibrates or shakes. I can stop and take off again with nothing happening. Would think tires out of balance would do it all the time. And a few times....pulling my 5th wheel...making a right turn out of a parking lot.....it feels like a rumble from the rear.
View 2 Replies2002 F250 4x4 ... There is a bull whirring noise that started about 4 months ago. I attributed it to tire noise. Then this past winter I put the truck into 4 wheel drive and it went ok, however everything started vibrating. First thought was u-joint however none are loose. Then I thought needle bearing, the axle has no play in it at all. So I looked at the drive shaft, it has a sloppy turn, not sure on how much play it should have.
Then you turn it and it then kind of binds up, you can push through that bind then it goes until it hits that spot again. I jacked the truck up and turn the wheels there is no noise. The noise is only when it is driven. Took it to ford and they came back with nothing, they replace the rear pumpkin gasket and cover stated those gears where fine and they inspected the rest, and came back with nothing. Should I just start by replacing front hubs and bearings and see what happens.
I have a 02' 250 4x4 with 250000 miles on it. While driving between 55 to 65 mph there is a roar and vibration that seems to be coming from the rear. I have about 35% tire tread left and have had the rear tires balanced and it still does it. Having issues with drive shafts unbalanced or rear ends?? I am not sure where to start....
View 1 RepliesI bought this Ex a little over a month ago and finally got around to replacing some stuff.
I have a slight vibration between 50 and 60 MPH. The vibration is the same weather I am accelerating, in Neutral, Coasting down (well, a little bit worse when coasting down), in 2WD, in 4WD, turning, going straight, hot or cold.
I have replaced the following:
Rear Driveshaft U-Joints
Tires and Rims
Upper and Lower Ball Joints
Wheel Bearings
Steering Stabilizer
Cleaned and Greased the Hubs
Greased everything greasable up front
I still have the exact same vibration as when I started. I can feel the vibration in the steering wheel as well as in the body of the vehicle. I am thinking that it may be in the steering linkage. If there is a loose joint then the wheels would be allowed to jiggle a little bit. I am at a loss. What else should I check?
Also, When doing the ball joints, I noticed that the tie rod ends were quite stiff. How stiff should these be? I can't move them by hand, but they will move a little bit when moving the free end of the tie rod.
I am taking it in for an alignment on Friday, and if I can't figure this vibration out, I might have them take a quick look into it. Would a stuck slide pin in the front brakes do this? Both sides on my truck are seized at the current moment.
I have an 2011 F250 gas. I get what feel like a wheel vibration at 48 to 50 mph. It then go as you go up in speed. Comes back as you go down in speed at about the same range. Had it at the dealer for a month they but new tires and one new wheel on the truck. Same problem. Moved up to Ford. The sent me to another dealer. Ford now tells me that this is a problem that exist in the truck and there is nothing they can do.
View 14 RepliesSo I have a 2016 6.7L love it but it has this vibration at 65 mph that is worse when accelerating up a hill. It feels like an out of balance wheel but I have had them balanced 3 times. road forced 2 times. My dealer replaced the driveline also. I did a test with 400 lbs of concrete bags in the bed and it was vibration free. It almost is like the pinion angle is off.
View 11 RepliesTires just balanced and rotated yesterday (second time just in case done wrong before). New ball joints and bars installed about 50k ago. Left front shock may be bad, but only slightly.
The issue: At about 40-55 mph, there is a rumble in the cab, unknown origination. Everything vibrates, although it "seems" like the left mirror is shaking more. The seat, floor, steering wheel, everything vibrates.
When I let off the pedal, vibration and noise go away, even within the "vibe zone". It only vibes when any throttle is applied, even just a tickle. I brought the engine up to the vibe zone RPM (1500-1800'ish) while in park and neutral, all seems fine.
I checked the U-Joints, they seem tight. I don't have access to a scanner, unless I want to pay the dealer.
"2004 Ford F250 FX4 for sale. 5.4l v8, automatic transmission, 4x4, 152,000 miles. Truck runs and drives good but needs a rear drive shafts due to a vibration above 50mph."
Are their any known issues with these? I am guessing it is a u-joint or something, not the driveshaft.
A vibration has just begun on my 00 f250 power stroke it's in the left front and happens when I hit a bump I changed out the wheel bearing assembly and I switched locking hubs with another truck all with no success don't know what else it could be it does go away if I lock in the hubs so idk
View 2 RepliesI have a 2011 f250 6.7 and I have a very bad vibration between 40-50 that seems to peak around 45-47. It also starts again at 80+ . the dealer told me they could not find a problem. Then another told me its normal. The tire shop around here told me the tires were shot so I bought new tires. No luck. It does not affect it if I change gears.
2011 f250 4x4 6.7 SWB. 140,000 miles
I just put a dual exhaust kit on my truck (cherry bomb extreme, single in dual out), and I've started to notice that around 2100-2200 RPMs, there's a high pitched vibration in what seems like the tight hand corner of my regular cab. It almost sounds like the glass in the window is vibrating, or a loose bolt, or something like that. Very high pitched, very noticeable.
View 2 Replies2004 6.0L Excursion Limited 4x4.
I recently developed a "rumble" with vibration while braking. I describe it as a rumble because I associate it to a similar sound, cadence, and feeling as if you were slowing down on the rumble strips you find on the side of the highway.
It is mostly only noticeable at lower speeds. I know the sound and feeling of warped rotors, but this seems different. If it makes any difference, one issue I've been dealing with is that the front transfer case does not release when 4x4 is off and hubs are in AUTO.
Purchased new 2016 450 platinum. Has less than 800 miles on it and has a terrible vibration between 70-80 mph... Already have taken to dealer who stated there was a wheel out of balance and that they fixed the issue. But still present.
View 14 RepliesIMG 4396 - YouTube
What this sound is? Been to the dealer 3x already and they are throwing parts at it and each time telling me its fixed.
I've got a 2003 350 7.3, with the zf6, approx 225000. I've been chasing a vibration that can be felt in the whole truck for quite a while. Feels like a wheel bearing danm near shot. But after replacing both wheel bearings and making over the whole front end it didn't go away. So I replaced the clutch and throw out bearing cause it was getting bad anyway. The vi ration is still there so I checked the harmonic balancer and it was bad so I replaced that. Still no dice. I know that it's coming from the trans, you can hear it in when jacked up and running in gear. Shifts fine in all gears. But the vibration/ clunking is there in all gears and it's getting bad. It feels like a bearing going out. Could it be input shaft bearing or pilot?
View 14 RepliesOk so I replaced the rear axle U-joints and hanger bearing and now have a bad vibration. I marked every joint to ensure correct reinstall . Today I put the old hanger bearing back on to see if that changed anything and it didn't. Looking for a pic of the rear shaft so I can see if something is different. I have a crew cab short box. I don't want to have the driveshaft rebalanced but I might have to. On a side note before I replaced everything the truck was smooth as silk...
View 14 RepliesI have an '03 F250 Super Cab, 7.3L PSD, 4WD. I've started getting a large vibration between 40 and 60 mph. Started after driving on the PA highways towing a trailer with a car and hitting several deep pot holes.
I have had the wheels balanced, rotated, balanced a second time by a different shop and had them perform an alignment - Still No change.
The garage I took it to said the hubs were shot so I had them replaced - supposedly with Moog, lifetime warranty hubs. Still - No Change.
The tie rods and steering linkages are a year old, so unless something was damaged (visually, they look good, and feel tight) it probably isn't them.
I replaced the ball joints around 80,000 miles and now the truck has 155,000 miles. They appear to be ok, with maybe just a little movement in the Passenger side upper.
If there is any movement at all in the ball joint, will it cause a vibration?
I plan to rotate my full size spare through all 4 corners this weekend to eliminate the possibility of a bent rim.
I have another set of ball joints and seals on order which should arrive next week. Probably next weekend's project.
I have an issue with a truck I recently purchased. I have a vibration that starts around 50, feels like a wobbling vibration. Than once I hit 75 it feels like the truck is going to fall apart. Heavy rumbling.
It's a Ford F-350 dually extended cab. With 115,000 miles on it.
I took it to the shop to balance out the wheels and all the wheels needed atleast 2 oz of weighs on each side. Some have as much as 4.75 oz on one side. Is it possible that I need 6 brand new rims?
I recently bought a 2006 F250 Super Duty, 4X4, 6 liter diesel. My issue is that I have an annoying vibration/bounce between 45 and 50 mph. I thought it may have been a tire out of balance, but even after replacing all 4 tires and rear brake pads the vibration is still there.
View 5 RepliesI recently bought some used rockstar 1s off a buddy, installed new tires, balanced, put tapered lug nuts on and I'm still getting a slight vibration above 40mph. Do I need hub centric rings? XD says no, I think I do.
View 2 Replies