Ford Super Duty (1999-2016) :: Upfitter Wiring Question
Jun 4, 2015
I currently have Aux2 hooked up to my on-board compressor and it works like a charm...so I'd like to think I know how the wiring works for the upfitters haha.
This weekend I installed an electronic solenoid valve for my slip-tank so I can fuel up on the go. The valve is 110V AC and had two wiring leads of the same color so I assumed either/or could be used for power and the other for ground. I wired it all up running a power lead from Aux3 back to the valve and grounded the other wire to the body. To my surprise...no power! Can a 110V AC valve not be used in this application or is my wiring simply messed up/not making contact?
View 2 Replies
Advertisement
I have a 2010 F250 and wanted to power a dash camera using the upfitter switches. I purchased a 12volt wire, but am unsure on where to wire it so that it will only power up when the ignition is on..
View 7 Replies
I've checked the fuses, the lights are on on the switches, but I have no power at the wires under the hood. I'm adding lights and would like to use those switches..
View 2 Replies
I want to install a set of upfitter switches but my truck didn't come with them...so I bought the switches and the relay/wire harness as well...I cannot find any good information on where to mount the relay and where an extra plug on that harness goes too. I have found the wires that attach and go through the firewall but I am not sure where the rest of this mess goes...my truck did not come with the wire harness already installed...
View 4 Replies
Recently purchased a 2013 F350 w/upfitters. Figured Ford would have made access to the stubs easier by now (previous was an 05 6.0 ) and of course not. A bit more challenging. What parts of the dash do I attack and how. As the dealer is willing to charge only 40 bucks to connect any wires I run to the vicinity, I figure there's a slam dunk sequence for access.
View 7 Replies
This has been beaten to death but all the old threads I read are for 2011 to present SDs so I wanted to make sure I can add these to my 2008 before I spend $ on the switches. Anything I should look out for on the install? Once they are installed I would like to add front and rear strobes along with a roof light for plowing.
View 3 Replies
I have the ford upfitter switches in my 07 f350 and i had two flashing lights wired to switch 4 (10 amps) for snow plowing. The lights were LED and shouldn't have drawn much power but suddenly the lights stopped working because thers no power going to the fourth switch. They work on all the other switches. What could be the problem?
View 5 Replies
Sure would be convenient when hauling the 5er.
View 14 Replies
I just got a 15 f250 with the console and nav system but it didn't come with the upfitter switches.
I picked these up and got a copy of the .pdf for the installation, but I'm finding it hard to follow for where the relay and box should install. I ran the wire up to the upfitter switch location and can even find a nice spot to connect the grounding wire.
I can't for the life of me figure out where the box installs and where the wiring harness taps into the main harness. Need a photo of where your box is installed and where it taps into the main harness?
View 6 Replies
How hard is it to install the upfitter switches and the fog lights? Is it all plug and play?
View 4 Replies
I am putting work lights and LED warning lights on the back rack of the 2014 F350 diesel in work. Where are the wires for the upfitter switches, and are they prewired into the fuse box, or do i have to hook them up?
View 7 Replies
I would like to do the high idle mod with my 2006 F-350 using the upfitter switches. I've seen a couple of threads about this but they are not real clear to me and don't mention the 2006.
View 14 Replies
Got my 240 amp alternator in and had all new 1/0 GA battery cables with a 250amp fuse in line made to do all new lines. I started tonight and found a small line going from the alt connector down the power line to a fuseible link (fuse) all in the power line
I wanna do away with the main 4 ga alt wire but obviously I can't do anything with that line going to the plug. Can I put a connector on it and wire that into the one side of the 250amp fuse.
The only other option is to add a wire to beef up the stock line ....
View 14 Replies
I have an early 99 F250 that I'm putting 08+ mirrors on. I'm not real sure what year they are, but no wiring diagrams I can find match up. See, my mirrors have 12 wires. All diagrams I find have 10. The colors don't match either. I wanna wire these up but I can't decipher the wiring.
View 2 Replies
I am looking for a wiring diagram for that taillights for a 1999 f350 pickup. I am working on a friends truck that doesnt have any taillights and I would like to have a diagram in hand before I get started on it.
View 7 Replies
I have been tracking down my ABS light and found that the left front wheel speed sensor has had the wiring harness ripped off from behind the front wheel. I have about 2ft of the harness coming off of the actual sensor.
Question is, since I cannot locate any wires that this seems to be able to be connected to, can I simply cut and splice these wires directly into the Tan/Black + Tan/Lt Green wires going straight to my ABS controller?
View 3 Replies
I'm currently trying to swap out the standard AM/FM/CD for a DVD receiver with backup camera, and need to find out the proper wiring colors and pin position. I'd rather not send it to a stereo shop, as I've seen a lot of hack work by so called "audio installation experts", and besides.. I have a shop and can do the work myself.
I tried looking through AllData, but since my truck is too new, Ford doesn't release a lot of technical info for us in the aftermarket. Looking for a link to a Ford diagram?
View 6 Replies
I have a mostly complete 1999 F250 XLT I'd like to salvage the power mirrors, locks, and windows from to install on my 2001 XL. I know the door harness and therefore the dash harnesses will be somewhat different. I'd like to see if there is a difference in the other ends where they connect to under the dash.
Looking for the wiring diagrams for those components so I can see what else I need to change?
View 2 Replies
On one of the trucks in work, the salt has corroded the truck side plug for the reverse camera in the tailgate. Because of this, the camera no longer works.
Is this part of the whole rear wiring harness, or it the tailgate plug a separate pigtail that can be replaced? If it is a separate part, what is the part number so I can order it?
View 1 Replies
Looking for a wiring diagram for the coolant temp sensor? 1999 F250 SD V10....
View 4 Replies
Driving the truck today I noticed mssg from info on dash " problem with trailer wiring". I wasn't hauling anything. the message went away on my next stop when a truck was turned off. On my next stop, I was pulling into a parking space truck stalled and I saw another message saying something like " please pull over safely and stop a truck." Luckily I was already parked. the truck would not start or even turn over. after about an hour truck started but brake symbol was on the dash.
View 10 Replies
