All week the truck was acting like the clutch was slight depressed when first taking off and then today i was driving and the underside of truck started smoking like crazy and slowly lost all the gears could put it in any gear and nothing just was acting like it was being revved. does this mean clutch is bad?
View 10 Replies2000 Excursion 4x4 v10 auto. Pulling the boat last weekend up the driveway from the lake and the truck started smoking under the hood at the top of the drive. Jump out and saw a fire under the pass floorboard. Go the hose and put it out in 30 sec. Thought i blew a trans line and it sprayed on the cat. Took it to the shop and he said lines are good it's not leaking. He said it is possible that the trans over heated and built up pressure and blew it out past the front seal.? What happened or how to prevent it from happening again?
View 13 Replies2007 f350. About 2 weeks ago my truck started smoking really bad, and I took it in to have it diagnosed. It was 4 injectors that were bad, so I had them replace all 8 and also install a bullet proof oil cooler. From the moment I got the truck back, it did not seem to idle as well as it used to, and over the next week, it began to blow a good amount of white smoke and run very rough.
But the weird thing is when I took it back to the shop to have it diagnosed, the minute I pulled into their driveway, it ran perfect, and they were unable to pull up anything. The next morning, I started my truck for work and as I drove down the street, the truck ran extremely rough, and seemed to be running in 2 cylinders. I shut the truck down, restarted it and it ran a little better, as I limped it back to the shop.
I was driving down the highway and the truck was in overdrive and under a load passing at about 20lbs boost and all of the sudden I lost all power, felt truck shake a little. The tow/haul light is flashing and got only one code P0730. The truck won't go into gear in either forward or reverse now, had it towed home and put a pressure gauge on it and found about 100psi at idle In neutral, in reverse and forward I got strange readings the pressure goes way up momentarily then down to 100psi, and increments back up to over 500 psi and seems to stay there but neither forward or reverse engage. I have no clue what could be wrong at this point. I am attaching a video .....
View 14 RepliesI drive a 2000 F250 XL Super Cab LB 2WD 7.3 Powerstroke. i drive like a grandpa. No rompin on the accelerator or anything. I was leaving the house got up to about 35mph and the truck lost acceleration. Motor still running fine. I coasted onto a side road. Put it in park, killed it, started it again and same thing. Will not go into drive at all. However will go into reverse just fine and accelerate in reverse. Desperately wanting my favorite means of transportation back!
View 14 RepliesStarted flaring between 3rd and 4th I changed the pressure solenoid and the direct clutch and no change. Flushed the tranny and changed filters and no change the oil is not burnt. When it flares it goes into a safe mode on the dash and will shift perfect through 4th gear no issues. I guess I've always know if it's bad it's bad but I don't understand why it works in a safe mode but slips in regular. Also if it is a bad tranny will a 3c2p-7000 work as a swap in my truck. 2008 6.4 4x4 ....
View 5 Replies2004 f350 lariat Key fob slowly started not to work until it finally quit. Thought it was the battery but changing it had no change. Do the fobs go bad and need to be replaced?
View 11 RepliesMy 2003 6.0 truck lost most of its power. It has the SCT programmer. It used to run great it would roll coal really well then it slowly started to run worse. Now it runs really sluggish especially when its cold. IT takes forever to warm up. On the freeway when ur going a constant speed it bucks and jerks a lot. It won't roll coal anymore and just runs like crap. A mechanic said I had 3 bad injectors. But I don't believe it.
View 2 Replies2002 sd 7.3 4x4. When I start up engine and put truck in any gear I get nothing but the ugly clicking sound when I shift back into park. Turn off engine and restart, everything works as normal. Doesn't do it every time 4-8 normal start ups then a bad one. Brought it to a tranny guy, head scratcher for him. Any other solution before I start changing parts?
View 6 RepliesI don't know what is wrong with my truck. I don't know what this symptoms called, but It felt like it was missing a beat. The engine suddenly lost power for a second or two wile driving. It did this few times. Is it the engine or the transmission? No check engine light is on. 2001 F250 5.4 V8
View 8 Replies2005 F-350 6L diesel .... Put new batteries in it a week ago.
Been running good then the radio quit a couple of times. It came back on after truck was restarted. This morning I go to town and the battery light comes on. I stopped and started about 5 times and on the 6th it wouldn't start.
I got a boost and started home it , started to try and quit when I was almost home. Was so dead the power windows wouldn't even work. Have it on the battery charger now and it starts right up but the battery light is still on and the ABS light is on.
So I went to start the truck this morning around 8:00 and it was 7 degrees outside, when the truck started the oil light came on and oil gauge was on low? So I turned it off right away. few hours later I tried it again and still nothing I thought maybe the oil was frozen. After I started the truck the oil was higher on the dipstick so I am assuming the oil pump is functional. What could be causing this? Could it be the the gauge is not working? The truck is a 2000 F-350 V-8 5.4 gas. I'm hoping it is something simple I am suppose to work this afternoon
View 14 RepliesI replaced a rear rusted brake line a couple of years ago. It rusted where the line met the bracket. I'd never done this before but bought a flare (flaring?) tool and fixed it.
This week the longer line that runs down the length of the truck started leaking. It looks like the line was once held in place by a small bracket just in front of the rear wheel but it wasn't in that bracket anymore. I guess it rubbed against the metal and water/sand rusted it out.
A local garage said they'd need to drop the fuel tank and estimated that it would be several hours (and hundreds of dollars) to do the job. It looks like I might be able to cut the old one out and then fish the new line up through there and replace it.
Also, what is the diameter of the line? It is a 2004 F350. I can certainly cut it out first and then take a piece of it to the local auto parts place to get the replacement line.
So a few months ago I would occasionally hear what appeared to be a slight squealing noise from a pulley when I started my truck. It was very intermittent, so I didn't think much of it.
After a few weeks, I realized I was only hearing it on colder mornings - it would also go away rather quickly. I bought a mechanic's stethoscope, and figured I'd get to it on a slow day.
Today, I finally broke out the scope and tried to figure out the source. Didn't really find any pulleys making noise, and I did notice that when I shut the truck off, it squeaks for a second or two as it comes to a complete stop.
My dream of finding a bad pulley or perhaps a power steering pump was crushed. I had hoped to do a little Easter wrenching and put this noise to rest. So, I did what any good mechanic would do - I Googled the issue.
I'm reading that it could be the belt. Certainly wouldn't bother me too much as that is an easy fix. The belt isn't too old - about 4 years and 20 - 30K on it.
I took a few pics of the belt and can take a video of start/stop ....
I had a can of fuel at home that had been siting around a while but I put it in my 02 F350 with the 7.3. hind site being 20/20 I shouldn't have done that. The truck only made it about 2 miles then started chugging and eventually quit. So I pulled the truck home and this is what I have done so far. I assumed that I had bad fuel so I started with a new fuel filter. I did notice that the fuel in the bowl was a milky white color. Not sure what that means. But the new filter did not work as the truck will not start. So after reading some other posts I decided to drop the fuel tank and clean everything.
I did that including cleaning out the 2 screens in the fuel pick up. After re installing the tank I put new clean fuel in the tank and primed the truck. But before starting it I drained the first amount of fuel out of the filter bowl just to make sure I got all of the bad fuel out of the lines. So after doing this I put a new filter in and primed the motor again. I appear to be getting good fuel pressure and the fuel looks very clean now at the bowl. But the truck does not even attempt to start. It turns over just fine but will not start. Some advice I can get before I have it towed to a shop. Also, the truck currently has 305,000 on it and has run great up till now.
While driving up hill at 60mph the truck lost power. Rpm jumped up as to change gears as it hit 55mph. Still losing power until it shut off. I tried to restart and just got a click from the solenoid. No engine codes whatsoever. Battery had 12.1 volts but when turning the key to start in getting 8 volts. Had it towed home. Today I swapped batteries with my other truck and same click noise from solenoid. All lights, radio, ect still work. Where should I start? Alternator, fuses...?? 2008 f250 5.4 ...
View 12 RepliesQuestion, my truck started to have a miss under normal acceleration, when I really get on it, it clears up? I also noticed a bad sulfer smell at idle. Im thinking the cat is possibly plugged? Truck had 172000ish on it, and the cat is original. I did do a big tune up this past fall, new plugs, coil packs, air and fuel filter. Should I put a new cat on it? And a new oxygen sensor?
View 9 Replies2002 5.4 super duty. My truck had started to ping, and knock worse over time. I did some research on this site, and I decided to remove my K&N air filter. Replace it with a traditional paper filter. Then I cleaned my mass air flow sensor. The results were great, no more knock and ping.I will check the MPG next to see if I get any improvements.
View 1 RepliesI have an 03 with a 6.0 diesel, going down the road and started losing power and then died. Won't start, and I don't have a scan gauge. Several sources said ipr valve, and from videos on youtube I thought may be a good place to start. I bought a socket and pulled the valve, to check the screen. There is no screen whatsoever on the ipr. The oils clean, as I had changed it about 200 miles ago, and I ran a magnet in the hole looking for a screen, couldn't find anything so I used my fluid pump in the hole. No trash, screen or anything. Do some ipr valves not have screens? What would be my next step??
View 2 RepliesI have 2 F-350 4x4's and they both wander back and forth when driving. They feel like they don't have enough caster. One is a 2000 V-10 extended cab with 8 foot bed. The other is a 2015 6.7 diesel crew cab with 8 foot bed.
I have driven the 2000 for so many years that I have grown use to the very slight sawing of the wheel to keep the rig straight. When my wife got her 2015 it does the same thing. The 2000 is leaf spring and the 2015 is coil spring. This bothered me when I first got the 2000 (used) but I just figured it was part of
the charm of a big truck.
I know I could put a caster shim in the 2000 but there must be a better way to solve the problem. Both are stock, no lift and no heavy winch or stuff.
I was driving my 99 f250 superduty and out of no where it sounded like i had blown a tire started to shake for at least 3 or 4 seconds pulled to the side of the road got out and check tires were good, got back on the road with no more problem.
View 1 Replies