Ford Super Duty (1999-2016) :: Transmission Will Not Engage In Drive Or Reverse After Replacement
Feb 7, 2014
I have a 1999 F250 super duty that blew a front seal on the transmission two weeks ago. I sent it to a shop and they replaced the seal, and torque converter. However when they put it back in it will not engage in drive or reverse. After working on it several days we replaced the transmission with another one from a service company. This replacement came with a 90 day warranty. However once it was installed it does the same thing and will not engage in drive, or reverse. I am not sure what is going on but with two doing the same thing it makes me thing maybe electrical or something else.
View 1 Replies
Advertisement
I have a 2006 F250 Lariat super Duty / 6.0 L engine / 143000+ miles / once started and transmission shifted into drive it takes 5 seconds or more for it to engage hard or if I build up the RMS then it jumps into gear hard, after it gets going it feels like I am driving on a washboard until it get warmed up good 10 mile or so. Is it the transmission filter and if so which one, I understand there is a small one on the outside of the transmission if so where? I can't find it.
View 14 Replies
I have just switched from GM to Ford and have a new F250 4x4 XLT. I am wondering how to engage 4 wheel drive correctly. I have the manual shifter and the manual lock hubs. However during my test drive I shifted the lever into 4H and 4L and it seemed to engage just fine. Do I need to lock my hubs as well? Or if im just in a wet spot can i just shift into 4h without locking my hubs? I know if I am in anything serious I need to lock the hubs. I just want to be sure before I get into a tricky situation. My 02 GM all i had to do was push a button and it shifted automatically.
View 7 Replies
Well it's been an ongoing problem with my 4r100, but last week it all come to a point. Reverse delay is getting to near 10seconds then abruptly engages. My 1-2 shift is so soft I have to look down and see my tach to make sure it shifted up. I now have trans squeal during ever shift including OD. Also have a loud screech that gets louder the faster you go, BUT the old girl is still moving the truck and oddly the fluid isn't burnt looking or smells burnt? That's one has me puzzled...
So Tuesday after work I'm pulling the transmission (in the driveway) and bringing it to the shop Thursday. Getting a billet steel converter, having all the planetary gears upgraded to six and four pinion, one way sprag will now be solid steel instead of the plastic one Ford put there, all the bearings will be upgraded to Torrington, I'll have the 45 roller sprag bearing upgrade as well as the 17 roller for reverse, I'm going with Borg Warner and Kolen steels, new solenoid pack.
I'm having the pump pump machined and sonnex upgrades done to it, spiral snap ring on OD piston, case will be machines not hand resurfaced, reverse gear plastic washers will be removed and the gear is getting machined for a Torrington bearing and steel spacer, clutch drum will be machined for a 360 spiral clip, locking snap ring on the OD piston, center support will have some machine work done to it, and I'm having the forward drum plug removed and the hole will be tapped for a steel plug.
View 14 Replies
I have a 2001 f250 7.3 powerstroke it is an automatic. It has the switch on the dash to engage the 4 wheel drive. When I turn the switch nothing happens.. no lights come on or anything. it has warren locking hubs. What my problem is???
View 2 Replies
I recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
View 2 Replies
Today I noticed that our 5R110 was delaying slightly when shifting from drive to reverse. It was probably about a 1-2 second delay but it replicated itself twice in a row. There was no delay going from reverse to drive. It is just an engagement delay. We are running a Superchips Heavy Tow tune on the truck, it is a 2006 6.0 Powerstroke.
View 4 Replies
2015 F-250 4X4 CC gas truck. 6R140 Transmission..
My truck has 6500 miles on it and since day one when I put my shifter in (D) there is a 3-4 sec delay in the transmission to engage every morning when I start out, rest of the time there is no delay even when the truck sits all day at work (about 9 hours). I have read in 2011 (?) that the transmission was loosening it's prime and would cause this problem, so how it's got me thinking.
View 9 Replies
I have a 2002 7.3 e350 quigley 4x4 Sportsmobile with 312k miles. 2nd owner. Bought it with 295k miles 2 years ago. From what I gathered the tranny is original.
After reversing at a downhill angle, stopping, and shifting the lever to Drive, the tranny doesn't seem to put Drive in gear and depending on the angle of the slope, the van will roll back or barely creeps forward even with throttle. Put it in 1st gear, and the tranny engages that in gear and drives forward no issues, then I can shift to 2nd, then Drive and the tranny shifts fine after that.
No weird tranny noises or clunking. Noticed this issue about a month ago or about a couple thousand miles ago. Did tranny service (drain, filter, fill) at the ford dealership at 305k months ago.
I can only replicate this issue when Reversing on a down slope. On a flat surface van Reverses and engages Drive like normal.
View 7 Replies
One of our trucks, 2004 F350 Powerstroke, my company truck, recently the last snow even we had, my tow haul mode would pop on and off almost evertime I shifted from drive to reverse while plowing. I didn't want it on, it just kept poping on and off. Thought maybe the button was stuck, but it moved like normal. My other thought was there is a loose connection in the shifter or column causing it to go on and off.
View 6 Replies
I continuously read that people with 6.2 F250s averaging 13 mpg or so in a combination city/highway driving. This 2014 4x4 barely has enough power to move itself (honestly, I'd rather have my Ram 1500 back) and barely gets 10mpg. Basically have to give it about half-pedal to even get up to freeway speed and floor it if i want to pass anything. Is it just that much of a POS or does this not sound right? Other than a massive "clunk" sound when shifting from reverse to drive or vice versa, no indication of any problems.
View 14 Replies
I just purchased a F250 Gasser with the 6.2. I made sure to get it with the 4.30 rear to babl to tow a little better when i upsize the tires a little. Where I can find the drive output ratio from the transmission?
View 2 Replies
It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problem, then when put it in Drive it revved like it was in neutral. There was no banging, no clunking, nothing to make it seem like something catastrophic happened.
I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more. Next I did the obvious and cheked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new.
I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? Ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check ***** were in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
Why this thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings? Can this be a "worn out" valve? or gasket issue?
View 1 Replies
Drove the wife to work this morning. The turn off into town there was a lady stuck so I pulled over in the drifts. After putting in back in gear I had to get on it to get out of the drifts. Snow was blowing over the windshield, and I imagine throughout the engine bay.
After that it felt like it stayed in 2/3rd gear. I'd hit the pedal and it would redline and sort of accelerate jumping in and out of gears. So i slowed down to a stop. Accelerated slow and it was ok but when I got more on the pedal it would feel like it was slipping. Once I got in the driveway, she idled for about 15 mins while I shoveled out my spot. Once putting in gear again I had to rev it up for it to move.
Also reverse, had to rev it up to move it.
View 2 Replies
I'm having trouble disconnecting the transmission lines to replace them. I can't get them off. I have the tool. Can I replace the fittings in the radiator?.
View 3 Replies
any generic fits for replacement trans drain plug - 2008 f-350 V-10?
View 3 Replies
I have a 2005 f250 super duty turbo diesel 6.0 automatic. The problem I'm having is, when I engage the tow/haul button the transmission doesn't down shift unless I feather the pedal. Also the engine will overheat at times. I've replaced the thermostat, but that's all so far.
View 2 Replies
I have a 93 f250 4x4 with a 5.8 liter with 69 thousand miles.. the problem I'm having Is if I put It in drive it won't shift out of first but if I manually shift it from 1st to 2nd to drive it works but shifts very hard. Sometimes it will shift in drive but It shifts really hard. I don't know what It could be. We just put the transmisson back into the truck due to having to change a broken flywheel. It just don't Seem like it has any power...
View 5 Replies
I got a 99' Jetta gls 5 spd. I just replaced the transmission and now the car won't engage reverse from inside the cockpit. Reverse can be engage from inside the engine bay, but when the shift knob is depressed nothing happens. Linkag cables are in the correct spots.
View 6 Replies
I have a 2001 F250 V10,
So the truck drove fine yesterday had zero issues... I used my auto start as I do every morning in this cold weather, get into the truck and shift from park to drive and its like it does nothing. I can free rev in N,D,1,2. Reverse works great.
I tried switching from 4wd to 2wd, no change. Reverse works just fine. No noises, codes or anything, just doesn't want to engage...
I am assuming I have a 4R100. Could something electrical cause this? I am thinking its mechanical, but hoping someone has ran into this before.
Literally no way I would have known the trans was going bad... It's always worked fine. Tranny fluid is full, I tried unplugging the battery waiting and plugging back in, no dice.
View 11 Replies
I have a 2000 F-550 w/7.3 and a 6 speed ZF transmission. My problem is that when you go to shift into any gear inc. reverse the transmission stays in 5th gear. I pulled the shifter and tried to do it from top of transmission it still stays in 5th. Any thoughts that I could possibly check?
View 1 Replies
