I have a 2000 SD F250, gasser, auto. Last week I pulled a heavy load and developed a tranny fluid leak. The fluid appears to be coming from what looks like a freeze plug on the bottom of the casing forward of the (torque converter?) pan . Is that plug easily replaced by a DYIer. Small leak. 150K on the motor. First time it has leaked. Heaviest load I've pulled.
View 2 RepliesBest truck I ever had but around 200k would occasionally blow a bunch of smoke when pulling a heavy load.
My 2000 f 350 xlt triton v8 has done the same thing a couple times (about 200k miles).
The (cough) "truck expert" at my local dealer has never seen that before but its happened in 2 different trucks for me. It never caused a problem other than scaring me.
I sold the 02 last year when i got a 2011 f 250--it was 12 years and 300k miles old and never was hospitalized except for a fuel pump due to my negligence of filter.
Truck blows smoke like a blown NASCAR engine occasionally when pulling heavy load....pull over, cool off and resume driving. Its as if it never happened. All fluid levels are in range and truck drives fine minus load. My last f350 5.4 did same thing at about 200k miles. My local ford dealer tells me I'm the only guy on earth this Has happened to.
View 8 RepliesSo basically I thought it would be a great idea to degrease my motor from the top down.... After washing I start it up and drive down the road to head abunch of misfiring under heavy load or high rpm's.
My problem is that the misfiring won't throw a code. I then proceeded to buy a new ignition coil (thinking this was the problem) but with no code to go off which cylinder was bad I just switched the good ignition coil into each cylinder and starting it.
Up each time. None of them seemed to make it better. Also the injectors all seemed to be good. So what to do ?
2002 Ford F-250 5.4l
I have a 2001 Ford F250 V10 crew cab, I am getting trans fluid in radiator. i have had radiator replaced. it was good for about 3 months.
View 6 RepliesI have 2000 ford f350 7.3 diesel. (Approx 95,000 mi). Tried to tow heavy wood chipper out of soft backyard, truck on angle because of grade. Put in low and second for better traction. After somewhat high engine rpm tires started to move me ahead until spinning occurred upon which I would immediately stop and try again (slowly). Next thing I know trans fluid on ground and truck steaming. Let cool down, refilled trans oil to proper level, unhooked heavy load. Fluid NO longer leaking, drive home fine (towing nothing). What are my next steps? Very concerned I've done grave damage!?
View 9 RepliesI drained the transmission fluid on my 2000 f250. I measured the fluid at about 6 quarts. I refilled with 6 quarts. I drove until the engine was hot and checked the fluid while running in park. Each time I check it I get a different reading on the dipstick. I wipe off the dipstick each time but sometimes I pull it out and it reads low. The next try it shows about 1/2 inch over full on the dipstick. Can't get two consistent readings. Is it harmful if it is a little over or under full?
View 4 RepliesI was driving to the store today and about halfway there the truck kept the same rpms but I was losing speed. The wrench lit up on the dash, checked the tuner (nothing out of the ordinary) so i pulled into the nearest parking lot and shut her down. The tuner is just there for my dpf delete and is set to "no power" or stock settings. It's a bully dog triple something or other. I don't race the truck or work it very hard for that matter. Basically a work truck that hauls more people than trailers.
Lifted the hood, checked the tranny fluid level and the stick was dry as a bone. Thing is, it's winter here and i haven't noticed any transmission fluid leaks anywhere ever. I'm gonna head to the local (two hour drive one way) parts store for fluid in the morning with my dads truck.
I'm wondering where it went? did it burn up or leak out and I didn't notice? Just wondering where to look first when i get it back home. Or did i simply fail in my maintenance checks (i admit i change my oil and fuel filters religiously but haven't checked the trans fluid) and it ran out??
Well I went about 20mi to pickup a door for my inlaws. Get about a mile from home and my tow haul light is flashing. Truck starts shifting strange then I smell it trans fluid. If course I get stopped by a red light shut it down. Started and had to rev to get it to move now four houses away from home coast into the drive shut it off and trans fluid is covering the entire bottom of my truck. Even the rear tires inside are covered. I had the wife crank it and I blew a trans line near the ext. trans oil filter. What are the chances that I did not toast my trans? No prior shifting or slipping problems before this mishap.
View 14 RepliesI have replaced the cruise control cut off switch and post-recall pig tail twice in two years for fluid leaks. Whats the deal do they all leak?
View 6 RepliesI have a 2008 f-250 6.4 Diesel. Yesterday the Brake Fluid light came on. I thought maybe a sensor, but once I parked and checked I realized my brake fluid was down to the Min line. I started looking for a leak and it was apparent that it was the front drivers wheel area.
I am attaching a picture of the brake. The leak is either coming from the area where the fluid line runs into the gold thing (caliper?) or the bolt at the bottom of the gold thing.
Put new backing plates, parking brake shoes, springs, etc on my 2004 F350 DRW 4x4. Replaced the inner hub seals and axle o-ring. Filled with Ford Rear end lube and went for a test drive. All was well. Went out last night to take her out again and I've got diff lube running out of both sides on the inside of the rims. Did Ford sell me the wrong seals? Could I have installed the seals wrong? Ford seal part number is 4C3Z1S177A. Axle is a Dana 80, confirmed by reading the tag on the diff.
View 2 RepliesI just recently had to replace the extension housing on my truck. Well after doing so I went to start it up and top off the tranny fluid and it started to leak out on the left rear side of the transmission near the extension housing. Ive looked and looked and found that the fluid is coming from the top right in front of the extension housing but when i clean it off there seams to be no holes or cracks. It isn't the housing seal, cause it pools in front of that. What could be the issue? My truck is a 01 F250 4X4 5.4L.
View 4 RepliesI have a 1991 300 6 with an e40d trannsmission, our 4610 Ford tractor broke down in the field so i pulled it maybe 50 yds with my truck, it didnt like it but it did it. Now my tranny is dripping at a decent pace it looks like from the hole in the bottom of the trans, drove it ten miles home and it shifts fine. What could i have done??
View 4 RepliesI'm working on my brothers 99 f250 super duty 2wd. The truck pulls to the right. Here's the list of things I've changed and checked
1. Gear box
2. Tie rods
3. Ball joints (aligned)
4. New bearings and seals
5. Brake rotors and calipers. Front and rear.
6. Rotated tires front to back
7. Rotated tires in cris cross pattern
8. 4 new tires (factory size tires)
9. Rebalanced tires
10. Aligned for a third time.
And the truck still pulls right. What is causing this!
Just had my tires rotated (which I do ever 5,000 miles) and an alignment done. Alignment appears to be in spec, but she is pulling/drifting to the right. Dealer suggested I get the tires cross-rotated, which I had done yesterday, but she is still drifting/pulling... not sure the difference. Pretty sure I have to get it back to the dealer to address, but just looking for other possible causes to potentially prevent that trip.
View 5 RepliesNew floor mats. My truck is going to be 10yr old and has the original King Ranch floor mats. I want some heavy duty rubber ones that will fit around my manual transfer case lever. I ordered the Weathertech digital fit liners and I am not happy with them so they are headed back tomorrow. They have a heavy duty all weather mat but not sure how it will work with my shift lever on the floor. Husky liners/mats look nice and heavy duty but won't accommodate the floor lever.
View 6 RepliesIs there a steering stabilizer for a 92 Ford F-250 custom 2wd? and what's the difference between a f250 custom and a f250 heavy duty?
View 2 Replies1999 f250 5.4L... Its done this 3 or 4 times now. Driving and it starts pulling to the right pretty bad, almost like if the front passenger tire was messed up or something. Today it did it, after I let it sit for a few min, then drove back to the house, it drove straight. Also, when it pulls to the right, its very sluggish, as if I'm pulling a very heavy load. From a stop, it doesn't even go until I hit the gas, and at that its very sluggish, sorts feels like if you drive off and forget the ebrake is on.
Also I've noticed some burning on the passenger side which I've read is probably the head gasket. I can see the oil dripping on the exhaust, causing the smoke. Also, my CEL just came on, with code P0401 "powertrain exhaust gas recirculation flow insufficient detected". Recently changed the plugs because it was running and idling a little rough.
At this point in wondering if the pulling issue could be something with the brakes, when I'm driving, it sounds like something is rubbing, I haven't looked at the brakes yet but I'm likely going to do new pads and rotors all around soon anyways.
My Superduty has been pulling to the left when I hit the brakes for a few months now. In the past it's done it, like within a year or two after buying it brand-new off the lot, but that was because one brake pad had rusted itself to the bracket and was not doing a darn thing. Once or twice more, it was a stuck caliper pin, which was quite obvious when working on it.
Last year, around August, I replaced the rotors and pads with Advanced Auto parts stuff. Rotors are still great, pads look brand-new, and it wasn't pulling up until the past month or two.
But this most recent pulling has been a problem that I can't find. It's not the pins, it's not the pads, and now I find out, it wasn't the calipers
This past weekend I went so far as to replace the calipers with Napa rebuilt "semi-loaded" calipers (all hardware and pins and bracket, except for the pads) and pressure-bleed the entire system. The old fluid was green, not black, but now that it's been bled, the pedal is a bit firmer than it was.
I wasn't going to replace the calipers without checking them first, but I broke both bleed nipples off and I wasn't about to wrestle with an easy-out and try to get the darn things out. Per side, rebuilt caliper with hardware and bracket, can't go wrong. (Checking the calipers would have involved using a C-clamp to compress the caliper slightly, then backing off the C-clamp - if the pistons come back out a slight degree, they are free and the seals are still "grabby" and resilient).
While bleeding it, I saw a piece of black crud (rubber?) about 2-3mm in size come out of the left side. Didn't think much of it, figured it was just built up crud from somewhere.
Today, the first commute after doing the calipers and bleeding, it's still pulling just like it was before the calipers. However, I did notice at one point when I hit them, they pulled like they normally do, but seemed to go straight a few seconds into it. It does seem that if I keep my foot on the brake, the pulling is much less after the initial second or two, but if I stab them again, it pulls like crazy.
And by "pull" I mean the steering wheel actually moves in my hand. So with that in mind, it's actually a front-brake problem. If it was the rears, the wheel wouldn't pull like it does, and if it was something loose in the suspension, I would have found it already after checking everything, and it again, wouldn't pull the steering wheel like that.
Now, given that black piece of whatever that came out of the left side, I'm beginning to wonder... if it was rubber from the inside of the hose.
Is the right brake hose causing the pulling because it's coming apart just like the left one might be?
I've gone over and over this in my head this morning, and thought about the ABS unit possibly dumping pressure from the right because of a leaky valve (see side note below), but I would think that once the pedal stab was over, it would even out and not pull at all.
However, this thing pulls left quite a bit, even after the pedal has been held down for quite some time. Usually. Sometimes, it subsides and doesn't pull. But mostly it does no matter what I do, keep pressure on the pedal, let up and reapply, whatever.
Does this really sound like a bad hose? It's intermittent, but usually pulls like 90% of the time.
Side note: The ABS unit in my truck, and most Fords of the time (not sure about later than 2004 or so) is a Kelsey-Hayes three-channel unit like this:
Kelsey-Hayes RWAL Antilock Brakes
It's the same system found in Chevy Suburbans and light-trucks, which I have worked on before and know a bit about.
In my case, it can't be a dump valve leaking, because it would effect pedal-height and not PULL to one side like it does. The only way that could happen is if the isolation valve was closed, AND the dump valve were leaking at the same time.
I haven't, however, gotten the ABS to activate just to see if it changes anything. On my way home tonight I will see if I can find some dirt or sand and get it going
I have an issue with a truck I recently purchased. I have a vibration that starts around 50, feels like a wobbling vibration. Than once I hit 75 it feels like the truck is going to fall apart. Heavy rumbling.
It's a Ford F-350 dually extended cab. With 115,000 miles on it.
I took it to the shop to balance out the wheels and all the wheels needed atleast 2 oz of weighs on each side. Some have as much as 4.75 oz on one side. Is it possible that I need 6 brand new rims?