Ford Super Duty (1999-2016) :: Tranny Would Not Shift Back Into Drive After Stopping At Stop Sign
May 6, 2013
I need to solve tranny problem, it started out a while back, would not shift back into drive after stopping at stop sign (after driving fine for about 20 miles) thought maybe dirty filter so did fluid and filter change seemed to work for a while then started again noticed it was mostly after using cruise control, but u joints were very bad, so replaced 2 of the 3 and worked fine for about a thousand highway miles, then got really bad. Now when I check the tranny fluid cold and /or hot it is way up on the dipstick. Took to ford dealer in ladoga, lied and said no speed sensor codes, but list on the paper he gave me had all kinds of abs and a p500 code.
View 9 Replies
Advertisement
I have a 99 f350 V10 gas dually dumper. Today while driving I stopped at a stop sign. When I went to continue the transmission seemed to be in neutral, then it caught and I drove through the intersection. It 2-3 seconds later disengaged again. I pulled over. When I attempted to put it in park it grinded. (Bad enough I just turned off the key). I checked the fluid. It was close to full and red. While in park I restarted. Truck started fine. I shifted into drive and nothing. It was like it was in neutral still. I attempted to put in park again and more grinding. Also while in park it does not hold the truck from rolling. After getting towed home I checked the tranny fluid again and it was still looking ok. I drained the transfer case also. The fluid in there was near black an appeared to have a metallic look. Does this problem seem to be just my tc or tranny issues also?
View 8 Replies
I have a 2002 F350 with the 7.3 diesel. I have had this truck since it had 30K miles on it and it now had 90K miles. It has been trouble free minus new pads and batteries. I recently changed the fuel filter and used a Donaldson filter. In the last week while driving the truck just mysteriously shuts off when I slow down for a stop sign. The only lights on the dash is the red battery light, and it fires right back up. I believe it has the original CPS in it as I have never changed it. Do you think this is the CPS going out or something else? I was wondering if the Donaldson fuel filter has anything to do with it?
View 5 Replies
Rebuilt trany after losing all gears filled the tranny and while cycling through the gear everything seemed to fine took it around the block topped off the fluid and went for a drive and it will not shift out of second and i lost reverse. What did i do wrong?
View 5 Replies
2012 f250 SC xl 6.2 - Is it normal to hear a single clunk sound on occasion when accelerating from a stop sign? Doesn't happen all the time mind you and I don't ever remember hearing it in the past.
Now just today, while backing up my driveway, as soon as I started the reverse motion, I heard the same clunk. Sounds like metal to metal and comes from the rear of the truck.
Only 7000 miles on her and I treat her like a baby...anything I should be concerned with?
View 7 Replies
I have a 2000 Buick Century that only has 70000 miles on it. I have an issue that when I drive the car for a while, the transmission will shift hard after stopping at a light or stop sign. It only does it through the first three gears. If I shut the car off and let it sit for a few minutes and start it back up, it shifts fine through all of the gears. I have not had the change to change the fluid and filter yet. The fluid looks clean and is always full. I have read that there has been a common problem with a pressure control solenoid in the transmission needing replaced to correct the hard shifting. I am not getting any kind of error codes from the PCM, so I am not sure.
View 4 Replies
When I shift into 4Lo I get no 4 wheel drive. 4Hi works. Did have a/c redirect to defrost a couple of times. I remember something about the air redirecting having something to do with not having 4x4 but don't know just what it was.
View 8 Replies
I was taking my boat out of the lake last night. Shifted T-box into 4Low and removed the boat. I then tied everything up and when to shift back into 2Hi and it wont. I have a 2001 F350 diesel w/ automatic and the auto locking hubs.Hubs are not engaged atm. I have never had this issue before and was wondering if a shift solinoid is stuck or something might be wrong with my Transfer case??
View 14 Replies
I have a 2001 F350 7.3 4WD that does not want to shift into drive. When you shift to drive you can feel a slight difference in the trans but it will not move, it will rev freely but not move. If I shift it up and down it will engage after a lag period ranging from 10-15 seconds up to several minutes. Reverse is ok and after forward engages it appears to work as it should, shifts ok through the gears. I don't have much experience working on automatics.
View 4 Replies
I have a 93 f250 4x4 with a 5.8 liter with 69 thousand miles.. the problem I'm having Is if I put It in drive it won't shift out of first but if I manually shift it from 1st to 2nd to drive it works but shifts very hard. Sometimes it will shift in drive but It shifts really hard. I don't know what It could be. We just put the transmisson back into the truck due to having to change a broken flywheel. It just don't Seem like it has any power...
View 5 Replies
I have a 99 F350 V10 that has started with shift issues. While driving in drive it will down shift to first for no apparent reason and not shift back up. If I drop the shifter to second it will go back into second from first. I can then shift back to drive and it goes back to drive. It will last a few minutes and then down shift again. It's a dually dumper if it matters..
View 2 Replies
My 2011 F350 is not engaging 4wheel drive from the dash switch. When I turn it to either hi or lo it says "shift in process" but no 4 WD. It will engage manually from the hub lock, no problem. I know very little about 4wheel drive but am otherwise mechanically knowledgeable.
View 5 Replies
I have a 08 6.4l F250SD. At 127k miles, it has been a great truck. All service has been performed by dealer. When I shift from Park into drive there is a 3-5 second delay, and when it drops into drive the truck rocks. Once driving there are no shift issues. Into reverse there are no issues.
View 14 Replies
I recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
View 2 Replies
I took my truck in for a clunking noise in the driveline as I come to a stop and sometimes when shift into park. It is now the 7th and I'm told parts have been ordered and the truck will be worked on when parts come in. I asked to speak to general manager and still no call back. I called customer relations and nothing they can do.
Honestly I think the have me on the back burner since I'm warranty work opposed to marked up repairs. Am I being unreasonable on my expectations of repair time? I called around and a ring and pinion job is quoted at 3 days at the most. Other repairs have been approved as well and parts are in for those, but they have not actually repaired them either.
View 14 Replies
I have a 2008 for 250 6.4 powerstroke. Issue I am having is occasionally when I shift from drive to reserve it will slam when I shift to reverse. It is an intermittent issue. What causes this and what to do?
View 1 Replies
So, in my 99 Bounder RV (F53 chassis), V10
I think it has a 4R100 transmission in it (I have not verified this).
I had the oil and filter changed about 10K ago.
Runs and shifts fine .... then I stop and idle with it in gear (say stopped in traffic for a few minutes).
Now the thing shifts super hard! I actually get rubber in all gears.
So I pull over, shut it off. Restart the unit and everything is fine again.
It does this very consistently!
I went to the local transmission shop. They said with 110K in an RV it could be anything and I should think about letting them rebuild it.
Now that is something I would do ... not diagnose a problem and just rebuild it. I thought a "professional" would actually look for the problem first.
I don't want to rebuild the transmission if there is small item that will fix this.
View 3 Replies
I have an 08 F-250 CC SB 4x4 Diesel truck that has since new clunked when starting out from a stop and/or coming to a stop. I have 16k on it now and am getting really tired of dealing with it... The clunk starting is when I let off the brake and just apply the throttle. It feels like something slips and then clunk.
The clunk when stopping is the same as starting, except when coming to a stop.This is unloaded or when loaded w/ cargo and/or trailers. I know I can go to the dealer, but I don't want to un-spartan my truck for this...
View 14 Replies
My F-250 super duty has a bump thump when I stop if I release the the brake it goes thump bump? Does not do this if I put it neutral. Seems to do this in Acceleration from a stop, shifting goes bump sometimes, When hitting rough roads does not seem there bump thump suspension issues?? Already greased the drive spline joint the same, checked if there is anything loose nope, checked spare tire secure , 75,000 miles stock shocks?? something in the transfer case?? The rear end just had the seals replaced??? Tranny is secure??
View 14 Replies
Yesterday wife left driveway and about a block away she phone truck "died". It actually starts and the engine is fine - shifting from park to reverse or any gear seems to have no effect. After tow home - i check and there are no codes (using ODBII scanner), the tranny fluid seems full and red. Looking carefully there is a slight rpm drop when idle into reverse or a gear other than neutral or park... but revving engine in any gear doesn't move the truck.
Is there anything else i should check before taking to a tranny shop? Its a 230k mile workhorse for the house but not critical if its down for a week or two. I have had it for 10 years and put the last 40k miles on it. Is there any diagnostic suggested given the symptoms?
View 4 Replies
Trying to troubleshoot a very intermittent (has happened on two different occasions during the last 1,000 miles) hesitation from a stop-light. I've been recording engine parameters (Torque application) on both instances as these have been during longer trips after a period of highway driving. 2004 Excursion, 112K miles.
This feels kind of like severe turbo hesitation (4 to 10 seconds trying to start out before it kicks in) but I don't think that's it. The turbo is a new PowerMax turbo replaced 5 months ago. VGT readings seem pretty normal. The EGR valve is new -- the first instance was with the old and the second was with the new. I've also recently replaced the EGR and Oil coolers (before this).
Here's what's interesting in the captured data though... Normally when I coast into a stop-light the indicated engine load stabilizes at about 40-50% and VGT moves to about 65% to 70% at idle. The two different times this happened (actually multiple times at stop-signs/light close to each other over 5 minutes or so for both of these), when I have coasted to the stop, the engine load increases from low values during coast-down (0% during freeway coast-down or 19-30% during other coast) up to 99.6% (or other similar high values) at idle and VGT seems to be full closed at 85%.
There is absolutely no response to the throttle in this situation for 5-10 seconds. I've either been goosing the throttle a bit or putting it neutral and revving it up first to get things going again. When it finally catches and starts accelerating with power, indicated engine load drops to 50-60% again and VGT opens up to 40-60% or so. None of the other parameters I've been capturing seem to read strangely during this that I recognize. No issues observed during cruise and power seems good. No pending DTCs or engine light.
Here's what the data points I'm capturing (once each second):
Boost
Calibration Input Volts
ECT
EOT
Fan RPM
FICM main volts
Fuel Injector pulse width
ICP
ICP Volts
IPR Duty cycle
RPM
Engine Load
MAP
Trans Temp
VGT Duty Cycle
EBP
EGR Commanded
EGR Error
Added today but not captured during these issues yet:
IAT
IAT2
Baro
Accel Pedal Position
Mass Airflow Rate
Mass Fuel Desired
View 14 Replies
