Ford Super Duty (1999-2016) :: Tapping Noise In Cab While Going Over Bumps
Sep 7, 2017
Like a lot of our trucks, mine had the tap-tap-tap cab noise while going over bumps. It always sounded like it was coming from the passenger side doors. I have read many solutions, but have never been able to solve my noise issue. But, I may have found it....or more truthfully, my wife.
The other weekend we were out running errands. As she climbed into the cab and shut the door she commented that the handle above the passenger door was getting real loose. She wiggled it to demonstrate.
Tap-tap-tap.
Same noise....... ....I'll be dipped.
Got home, grabbed a socket wrench and tightened the 2 screws. They were like 3 turns loose.
Noise seems to be gone. Time will tell, but if you have"that noise" check the upper passenger grab handle.
View 4 Replies
Advertisement
My 2016 f250 Lariat 6.2 4x4.. Question.. There's some sort of tapping noise that comes from underneath the under carriage like around exhaust area it seems.It's like a tapping sound the truck makes once its turned off. Does it about 6 times every 2 to 3 minutes.. Cant pin point the noise.
View 8 Replies
I have a 2002 F350 Triton V10, Automatic 4x4 Lariat. I have a tapping noise in my motor, and I've had people tell me it could be the timing chain slapping around, a rod or lifter. The tapping noise gets quieter after the motor has warmed up, but gets louder when given gas. I've been told to try thicker oil, pure gasoline (no ethanol), The truck runs fine for the most part except for a vacuum leak on the top part of the motor underneath the throttle body. I have someone that says they can work on the motor and so on. But I don't know where to look to buy the parts for the motor, and what I should have replaced, while he's got the motor out and apart, so far he said he'd change the lifters, timing chain, the vacuum leak.
View 4 Replies
My 2013 f350 long bed diesel pickup has a noise in the front end when going over a bump such as a curb at low speed. It will also occur if turning onto a side street that is at a downhill grade. The vehicle has 4000 miles and is just at one year old. The noise sounds like a shock housing scraping on the shock or a very dry and rusty bushing. It also sounds similar to the anti-lock pulsing. I have had it to the dealer twice and they can not find a problem. The noise is very loud and easy to hear. I have gotten under the truck and looked around to see if I can find any evidence of rust and do not. Sometimes if I have my foot on the brake pedal when the noise happens I feel the anti-lock pulsing.
View 7 Replies
All the body bushings have dry rotted away on my 08 Superduty. Are these hard to replace?
I am starting to hear and feel more road noise and rattling when going over bumps or a rough road. U think they would have used polyurethane bushings instead of rubber.
View 14 Replies
When I go over good size bumps, I hear a clunk in the front tire area when my driver's window is down. It's a metal noise, like something loose.
2011 F-250 with 203K miles. Replaced shocks last year. Did this with stock wheels/tires. Something in the front suspension or axles. What should I be looking at?
View 8 Replies
I have a 2000 F250 2wd 6spd with a loud banging noise that has been vexing me for quite sometime now. The bang happens when I go over bumps (even small ones like road reflectors) while driving. I don't think it is suspension related since all the ball joints, front/rear swaybar and endlink bushings have been replaced fairly recently. All the springs and bushings also look okay.
The noise seems to come from the rear, and I notice that if I let off the gas when I go over a bump, it does not make a sound. Conversely, if I am accelerating aggressively and hit a bump, the sound is much louder. Also, if I step on the clutch while keeping my foot steady on the gas, it makes a bang. Jumping up and down in the bed while the truck is parked does not recreate the sound. I have already greased the driveshaft spline joint so I'm thinking the sound might be differential or transmission related. What it could be?
View 9 Replies
What this clunk could be?? in my truck in signature, 2003 F350 CCLB 4x4, 4" lift. its only low speed, on very light bumps. really does it when the truck flexes, like turning into an elevated driveway or something. driving me absolutely insane the last few months. it sounds like its coming from right under my feet
-removed front shocks and drove
-removed front sway bar and drove
-front wheel bearings are new and tight
-front leaf spring, rear upper shackle bushings are new (thought that was problem..no)
-front leaf springs and bushings are new, although i suppose its possible to have a bad bushing already
-removed traction bars and drove
-removed front track bar and drove, but going to try this again.
-all cab mounts look ok
-took out cab mount under drivers foot, and cut down the metal piece a little...read about it on another thread on here. no change
-made sure my gooseneck ball couldn't rattle
-steering box is new...thought that was it
-steering shaft is solid
-transmission mount bushing and crossmember feel tight
-lubed front driveshaft slip joint and it doesn't have any u joint play
-rear shocks seem ok but haven't removed them yet
-fuel tank is solid
-rear driveshaft has new carrier bearing and u joints, all is tight
-exhaust is not hitting anything
-u bolts all tight, spring bolts are tight
As you can see, I've been through damn near everything. my only thoughts right now is a possible bad cab bushing, or bad leaf spring bushing...as it sounds like its right under my feet. and when you flex the truck, it makes all sort of popping and clunking noises. i had the truck on my buddies lift and we went under it for an hour yesterday looking around with no luck. only thing i found was a bad traction bar bushing but we removed them and it still does it..
Most noticeable at the end of the video...it sounds exactly like a bad sway bar bushing but that's not it...
Front end clunk - YouTube ....
View 14 Replies
I have 2004 Super Duty with a noise in the front end when I hit bumps or backing out or entering a driveway with a lip. I don't feel anything in the steering wheel but I feel it on the floor board with my feet? Where to begin?
View 3 Replies
My 2000 f250 7.3 has pretty sloppy steering and noise in the front end when going over bumps. I have replace the drop links, swap bar bushings, both wheel hubs including new seals and the drag link. The rest of the front end seems to be in good shape. I put it up on jack stands and there is some movement in the front end but it seems to all be in the steering box.
Steering box appears to be original with 220k miles. I went to tighten it and it appears the PO did it at least once already. Is it safe to try tightening it again? Does tightening it increase the risk of failure? I'd like to try tightening it first but not at the risk of losing steering at 65mph with my kids in the truck.
View 14 Replies
I bought a 2000 F250 V10 Super Cab. Oddly after a few weeks it has grown on me. There has been a clunking noise out of the right front over bumps. I traced it to a bad axle bearing. The u joint moves up and down about a 1/2 inch. Besides pulling the hub/bearing assembly out and removing the axle are there any surprises getting the old bearing out?
View 1 Replies
2002 F-250 7.3 4x4 ...
I have a rattling noise coming from the front suspension (both sides) when going over small bumps. Most people point to ball joints, but I find my case odd because I just replaced
Upper/Lower ball joints
Track bar
Tie rod ends
Shocks
Front U joints
Drag link
I did not touch the leaf springs or the sway bar, except to grease the links, which otherwise looked good.
View 3 Replies
2001 f250 7.3L......
Haven't had it long, but when I am in gear and come to a stop i hear/feel this sound coming from what seems to be under my feet. I don't know how else to describe it other than it sounds like a woodpecker is tapping on the floor.
If I put it in neutral it stops. As soon as i let off the brake it stops. It doesn't do it while driving.
View 6 Replies
I have a 2004 F250 with 5.4 Triton engine. It stalls when tapping on Power steering reservoir! This is the oddest thing I've ever seen! I did not get time to look into it today but will sure do so tomorrow.
View 2 Replies
I've had my f350 7.3 for about 5 years now, she's my work truck so I plow and do a lot of towing. Had moog upper and lower ball joints done about 4 years ago seeing I dident know much about trucks then. As I learned more I started doing stuff myself, did sway bar links cause I was getting a bad clunk going over certain bumps and it totally fixed it. Just replaced tie rod ends and shocks but I'm still getting this clunking it seems when the truck rocks side to side, when I leave my driveway apron every morning I can hear it. I did a balljoint check a few times moving the tire up and down to check for play but everything seemed tight, not sure if it could be bushings or what I'm stumped
View 4 Replies
I just bought myself a 2003 F250 XLT with the V10 in it. Low miles, not beat, 6 speed, very happy with it. I noticed today that there was an inconsistent tapping coming from the passenger side valve cover. I searched online and was pointed towards the PCV baffle. I pulled the breather hose off and stuck my finger in the hole, and the baffle is indeed detached. Now I know that I need to pull the valve cover now to at least remove the baffle; is there anyway to reattach the baffle, or do I need to buy a new valve cover?
View 8 Replies
I was going to put new ball joints in but wimped out and had my mechanic do them. I'm too old to be doing that kind of crap. I just replaced the fuel pump with the correct one. That's enough under truck time for a while. 91,000 miles on the originals, stopped the rumble / rattle when I hit bumps in the front end. Getting the alignment Tuesday. Guess I got my money's worth out of them. Still has original brake pads too. Thinking of doing an upgrade to the brakes, drilled and slotted, I tow an RV and need it to protect the idiots that pull out in front of me. 2001, V10, CC ......
View 8 Replies
I've got a 2WD 2001 F-250 P/S Super Duty that is almost bone stock. The only suspension work done is the addition of air bags which are deflated. Whenever I hit ant bumps it feels like the rear axle is gonna come up through the bed of the truck. I've changed the shocks and there's no change.
Cars and other trucks seem to take the same bumps like a Cadillac.
will go towards saving my marriage since I'm building a house 1/4 mile from a R/R crossing.
View 8 Replies
My truck has been shaking/jiggling like crazy after hitting a quick succession of bumps and potholes and won't stop until I bring my truck to a complete stop. Happened 4 or 5 times in my old '87 F250 over a period of months, happened 4 times starting yesterday with my '02. Heard it may be the steering damper shock.
View 9 Replies
So loving my new to me truck. Only has 140K on it. But one thing that bugs me is that with the doors closed tight, when I drive over bumps, they sound like they are not closed. Makes you feel like they will fly open. But when checked they are closed all the way. Is there an adjustment or something that can correct this?
View 5 Replies
2004 5.4L F-250 ... it's a one owner truck I bought brand new in 2003 and only has 50,000 miles on it.
I have the 2V 5.4 engine no tuner or chip. 4x4 with 4" lift and 35's and I changed the rear to 4.88's. I love the truck but my problem is when I hit a large bump or drive too fast on a dirt road the fuse#23 that controls the PCM will blow. Consistently. I have to keep a box of 20 amp fuses handy. I have a 2 post lift in my shop and have scoured over every wire that is connected to the fuse. The EVAP solenoid, AC Clutch, Transmission solenoids and the O2 sensors. I only have 2 sensors I could find one on each side of the headers.
I couldn't find any rubbing wires or exposed wires. I am at a loss. It only happens when I hit a large bump. Could it be the Torque Converter Clutch Solenoid?
My brother in law is a mechanic and he brought over the diagnostic computer and when it blew while hooked up he seemed to think it was the TCC solenoid because when it engages the chart shows it angling up but when it disengages it drops off straight like it should. My truck seems to run fine when the fuse isn't blown, but when it blows it goes into a limp mode with the tranny stuck in 3rd or 4th gear and I have to drive it home in 1st.
View 3 Replies
