Ford Super Duty (1999-2016) :: Substantial Vibration When Torque Converter Locks
Mar 31, 2016
I have a bone stock (other than exhaust) F-250 SD, 6.0 auto, 185k miles. I have a substantial vibration when the torque converter locks - about 50-55 mph. Once the transmission warms up (i.e. 4-5 miles from a cold start) the vibration goes away and the transmission performs flawlessly. Backing out of the throttle and allowing the TC to unlock makes the vibration go away, as does shifting into neutral. There is no noise, just a vibration that will shake the whole truck. Transmission fluid looks good, and showing full. Have had the truck about 4 months, and have not flushed or replaced the filters on transmission.
I've seen a couple of similar threads on vibrations, but not one where the vibration will completely go away. I'm thinking replace the torque converter but wanted to get more information from the experienced experts that know these 5R110s better.
2007 F-250 King Ranch 6.0 PSD, 5R110W, 4" Turbo Back, Otherwise bone stock, 185k.
View 11 Replies
Advertisement
When running up through the gears under normal acceleration I can feel almost a double shift in 5th gear. It doesn't occur using tow/haul so I assume it is the TC locking up. Everything else seems fine. Truck has 9k miles, mostly towing. 2016 6.2 ....
View 6 Replies
I have an issue to where every once in a while my truck will not shift and when it does shift it slams into gear, and my overdrive light flashes and then I'll turn the truck off let it sit and crank it back up and it drives fine and the overdrive light is off. It shifts normal and smooth other than when this happens. Not sure if it is my torque converter or maybe a solenoid or what. My truck is an 07 f250 6.0 with 192,000.
View 5 Replies
I recently purchased this truck so I don't have any history on it. It's the V10 motor, automatic, 4 wheel drive, with a crew cab. I took it to Advance Auto to have them read codes and it came back with torque converter solenoid fault and 2 other codes related to that part. I didn't get to see the actual code numbers.
I've talked to 2 transmission shops and they said they could throw a solenoid pack into it, but that it might not even fix it. The truck drives fine, shifts fine, the tranny oil looks and smells fine, so I'm tempted to not worry about it until something else happens.
The truck has 217,000 miles on it...
View 10 Replies
I have a 2002 7.3 with the 4r100 173k miles. If your nice to it she drives fine, but if you get on it the torque converter will slip/stall kinda revs up like 300 rpm then slams really hard between 1st and 2nd. Other gears work fine. I've only had it not happen like 10 times since I've owned the truck ..... I don't really beat on it except for towing which I'm starting to do a lot of. Wondering if putting a new stock torque converter in it is worth it.? Not gona blow the bank on a TC unless I'm putting a brand new trans in the truck. Which I don't think it needs in the near future.
View 14 Replies
Switch out a 5.4 in a F-250 4X4 4 my neighbor now I have a noise like fan blades hitting coming from the torque converter it goes and comes and hits good in reverse...
View 9 Replies
We've gone through pretty much every other option as to the vibration on take off and other high torque situations and have pretty much settled on the the driveshaft as the issue. I added traction bars recently thinking that the old leaf springs just aren't up to the job anymore. That seems to have worked some but it's still there. We've gone through the rear diff also and that's good. I'm looking at options for replacement of the shaft. What are the current thoughts on one piece shafts? Is aluminum the better option?
View 14 Replies
Torque converter lock V6 vs. V8.
When O took my V8 in for service the dealer gave me a V6 as a loaner. I noticed right away that in 6th gear the torque converter locks up and stays locked until the gas is pushed way down, then, if I push further it shifts down to 5th. On my V8 it does not seem to lock at all and acts like 50's automatic.
It this normal? Can I change the setting at which the torque converter releases the lock? Clearly the 05' V6 has different programming. I have have drive a standard transmission all my life and this is my first automatic and I much rather have that connected feeling between engine and road!
View 3 Replies
So, I was on my way back home driving through the middle of nowhere Utah late at night, when I had an injector tip crack. I was able to identify which one and unplug it so I could get to Grand Junction, CO (about 350 miles away) where I have family. After a power nap I started calling parts stores and found an injector from Advanced Auto Parts (I couldn't find a motorcraft reman, but I was restricted for time). Installed it and all seemed good so I hit the road again. However, nothing changed. It still had the bad miss (rough idle, jerking/bucking when the torque converter locks up) just like when I had the injector unplugged.
The truck is an early 2004 6.0. It's the number 4 injector. I finally got home and hooked up my AE scanner to discover a #4 injector circuit low P0270 code and circuit contribution/balance fault P0272. It's definitely missing because disabling it has no effect. This could be a loose connector at the injector or FICM, because I can't afford another injector right now.
View 14 Replies
What torque setting I should use for lug nuts on a 2000 F-350 dually?
View 7 Replies
ill be replacing my muffler here soon, its rusted out blows smoke out all the rust holes, and so on. gonna replace with a nice flo master. Question is, when is it time to replace the catalytic converter? 15 years old and 93000 miles, it still seems like its in good shape, but could it be getting clogged? just from the sounds of the exhaust the past few months, it almost sounds like the truck is somewhat congested. The power from the engine is kinda week, but that's the engine itself. I have no real problems getting up to speed. my hesitation issues from before turned out to be water in the gas tank. Figured since im down there does it make sense just to bite the bullet and throw a new catalytic converter on?
View 8 Replies
Been doing a lot of reading about shudder/vibration on the 2011+ F150's and it seems to all center around the two piece driveshaft found on the longer wheelbases and more during take-off than other times. I have an '11 5.0L 4x4/auto with the 145 wheelbase and the 1-piece aluminum driveshaft and am experiencing a shudder in 3rd gear primarily, most noticeable during light acceleration with medium load (like gently accelerating up a slight incline).
When this is occurring I can see the tach needle fluctuating just slightly (maybe 50-150rpms, just barely bouncing) but I have no check engine light and the only time I have take-off shudder is under hard acceleration which feels like axle hop (which isn't too rare on soft leaf springs with 360hp engines!).
Anyways, this 3rd gear shudder is very soft and nobody has noticed it that has rode in the truck with me, but it sure feels like the old AODE/4R70W trans would when the fluid was getting old and the TC started to shudder during "soft" lock. 5.0L? Certainly could be a miss, though power is good, mileage is great and no CEL is lit...
View 6 Replies
I have a 2009 F-250 4x4 with a 5.4L and a manual transmission. I am looken to get more low end torque and a few more horses. I am thinking about starting out with a programmer and/or headers. Is this a good or bad idea.
View 6 Replies
On my '99's 5.4l with 55k, I've got a slight misfire occasionally with lower rpms and higher torque - basically going up a grade that's not quite steep enough for the truck to downshift, but clears up right away the instant it downshifts and gets some rpm. It generally seems like weak spark, or perhaps an injector spray pattern such that it doesn't always get fired off.
To give some history, the truck had more or less sat in a farm garage for ~5 years driven maybe once a quarter before I picked it up ~2 years ago. When I first picked it up, it misfired all over the place. I didn't think much of it, considered it gummy fuel, and dumped a couple cans of SeaFoam in the tank, replaced all 8 plugs (pretty sure with motocraft plugs though I don't explicitly remember), checked my air filter, etc and the misfires cleared right up and it purred nice and smooth like a happy little motor. That was at ~45k, or 10,000 miles ago.
Now it's starting to hiccup again and I'm not entirely sure why. The plugs should be nowhere near burned up yet and there are no lights on the dash. It's never come close to overheating and the only oil leak I know of is that famous small drip on the inside-rear of the passenger side bank drips on the exhaust header just enough to stink every so often when I come to a stop. I don't believe I'm burning any oil and certainly not near enough oil to foul a plug. Including that drip, I go about 3,000 miles before needing to add a quart. I've dumped 2 bottles of Berryman's in the fuel tank and it seems to work, but it's definitely not gone, so I'm thinking it's probably not oil related and more fuel/spark.
I'd had it in the back of my head to replace the fuel filter as well, but I hadn't gotten around it yet as it seems to be getting fuel at high rpm's just fine. I went ahead and bought the filter the other day and plan to install it shortly. It doesn't really make sense that that's what it would be, but I figure I'm due and it's worth a shot. If they were old plugs, I'd just replace them out, but they seem to new to be causing any issues.
View 2 Replies
What torque value is in foot pounds that Ford recommends for the 10mm bolts that attach the overload spring bumper brackets to the frame on a 2014 F250?
View 5 Replies
Torque on the differential cover bolts, 2016 F250?
View 6 Replies
I finally got around to installing a transmission temp sensor in our '06 F250, and I have noticed today that it seems to be at 180 degrees regularly driving around town unloaded. It has been around 80-85 degrees outside today. We just got this truck about a month ago, so I'm still getting used to its little quirks. On our old 7.3 with a 4R100, it wasn't at all unusual to see 180 on a day like today around town. Is this normal on a TorqShift?
View 13 Replies
Replacing EGR cooler/ EGR valve. Are there torque specs going back together with the EGR system? or is there a forum that has all the torque specs id need to complete the job.
View 4 Replies
My 2003 tailgate locks by itself sometimes, has been just annoying, but today I can't unlock it. It has no electronic lock. What to do?
View 9 Replies
Recently my 2011 f250 sd 6.2s check engine light came on so I took it to my local dealer it was throwing a p0430 code, they said bank 2 cat converter wasn't do it's job so it needed to be replaced. I am concerned that there is an underlying cause of the premature cat fail. I pushed the issue with the service manager and he told me that's all they could do was replace the cat and refused to check anything else on the truck. Is this common? The truck runs and drives fine. I'm just concerned that they are just throwing parts at it to get it out the door.
View 5 Replies
I put new batteries in the fobs, and my electric locks work using the buttons in the door.
Checked the key fobs at autozone.. they are ok.
Is there a training procedure for Ford OEM fobs?
F250 2002 4x4 5.4 Lariat Crew
View 14 Replies
