Ford Super Duty (1999-2016) :: Small Diameter Rubber Hose Dangling From Front Driver Side Brake Housing Area
Nov 2, 2015
I was just under my 2000 F250 7.3l crew cab truck and noticed a small diameter rubber hose dangling from my front drivers side brake housing area. It is attached near two other cables which are similar to cables on the passenger side. I don't see a similar hose on the passenger side. The hose is completely deteriorated and broke off up higher towards the engine. I cannot see where it goes. What it may be?
View 4 Replies
Advertisement
What this might be? (see pic)....
View 14 Replies
Noticed a small oil spot on my drive way where i park my truck the other day. Got up underneath and saw it was leaking from a rectangular rubber grommet on the front of the transmission bell housing.
What could be causing this? Have heard a few different things, turbo line leak, turbo pedistals, HPOP leak. Seeing what Super Duty Nation thought of the problem. Going to the dealer sometime this week.
View 1 Replies
So I'm away from home on vacation also away from my tools. Any ways my front drivers side line busted almost causing me to crash earlier today in my 2006 F250 6.0 diesel 4x4. So basically my question is: what tools are needed to do this job? I've already picked up the part now tomorrow morning I will be changing the part...
View 2 Replies
inside round thing with 4 notches in it is a smaller diameter than the new hubs. Will theystill work?
View 6 Replies
I am getting ready to make a set of front shackles for my truck for a temporary lift solution to fit my 35s until i can afford a complete suspension lift kit. I cannot for the life of me find the size of the hole for the bolts. I don't wanna drill it too big then have play in the shackle. My stockers are still installed so I don't have those to measure just yet. Need to verify the diameter hole i need to drill? and stock shackles look to be about 5.25" center to center, from what i can measure with them installed on the truck? so 2" lift, the new shackles will need to be about 9.25" center to center, right? (add 4", nets a 2" lift?)
View 7 Replies
I've got a 2008 f-250 extra cab. A small bump will cause the rear driver side door to pop open. What I have to do to fix it, I don't want the grandkids falling out.
View 2 Replies
Need the fuel system diagram or schematic for my truck.
1999 250 superduty v-10 Ser# 1FTNF20S1XEC67940
Every time I run it I smell gas. I changed the f/p 6mo ago. While I was working on it I noticed there was a hole rubbed in a small hose. I assumed it was a return line (smelled gas before too) and when I fixed it the smell went away until lately. I dropped the tank,yesterday and didn't see any problems. Just need to find out what hoses go where so I can replace the hoses??
View 7 Replies
I have a 2013 f250 6.2, I bought the truck brand new only have about 3000 miles on it and the other day I noticed that the drivers side front is lower then the passengers side front, the drivers side is about one inch lower, this doesn't seem right, also my drivers side front wheel seems to be pushed forward about one inch to the bumper that also doesn't seem right.
View 3 Replies
The used 2004 F-350 I bought has developed a driver's side front end howl between 45 and 60 mph over the last 1000 miles. I tried all the standard stuff, rebalanced tires, rotated tires, put on a set of tires from a friend's F-350, replaced wheel bearings, replaced ball joints and nothing has worked.
View 7 Replies
Ive got a 2002 f250 Sd 4x4 with 93000. Im getting severe vibration from the front drivers side at highway speed. I thought it might be a warped rotor but i cant feel it in the brake pedal, when I put the brakes on. How can you tell when the hub bearing assembly is going bad? The truck doesnt pull to that side either. I can hear it, and feel it more when i'm going around highway corners. When im driving through town, I can hear a "clunk,clunk,clunk" noise coming from that side also.
View 14 Replies
I noticed an oil leak out of the front housing of my 2016 350. I have 3 Ford dealers nearby and all 3 can't get me in until 8 August. It looks to be just a few drops daily. Is it safe to drive pulling a 5th wheel until they get me in? The leak is at the bottom of the housing.
View 3 Replies
2011 f250 6.2. put it in the shop to have the rotors turned, and front brakes while they were under there. Now it pulls to the right whenever you apply the brakes. Can smell brakes on the left front after a short drive time. Replaced that caliper and it's still doing the same thing. I'm stumped at this point.
View 9 Replies
My truck has an intermittent shake with a grinding/binding kind of noise. It seems to happen at lower speeds, generally when slowing down and turning. When I apply the brakes or speed up it seems to stop the noise.
The rubber/plastic seal on the back of the wheel hub is loose on both drivers and passenger side but I don't think that is the problem. I'm wondering if it is the u-joints or something.
The brakes look shiny and i don't see any scratches on them so I don't think there is a rock or something in there. I have the wheel hubs in the auto setting, and it is a 4x4. The truck is a early 99 7.3L with a leveling kit and 230k miles.
View 4 Replies
Truck is 2007 6.0L 4 door F-250 FX4
So this started after some High water encounters around my area. All freshwater. Went to the store and then i notice the truck pulling Left and got home and checked brake temps and the driver front and rear were over 400*F passenger side was 150* or less. No trailer no load in the bed. I decided to clean everything. Pads are worn but still have life.
Rotors showed some signs of where the pad is dragging Not bad though just a small area close to the top hat. I cleaned pads, carriage, and clips and reinstalled everything with some anti seize on the edges of the pads where the clips are and at the same spots on the carriage.
Thought it was ok but the after more water and a day or two sitting the same thing happened again. It is only the drivers side and it's both front and rear. I am stumped on this one. Two calipers going bad at once? I need to tow a boat on Monday So I have got to fix this.
View 1 Replies
I've got a 02 SD v10 4x4 with Warn hubs and 97k. Bought it a couple months ago and I've noticed a vibration coming from the front driver side. Symptoms are that of a bad wheel bearing; vibration that increases with speed and not RPM, seems to lessen on left handed turns (weight transfers from driver side to passenger side) and gets worse on right turns. Also the truck seems very twitchy and hard to keep straight on the highway.
Snowed the other day so I locked in my warns (just in case) and I instantly noticed the noise and vibration almost went away entirely except for on the freeway around 70+ mph. Also noticed it seems less "Twitchy" on the freeway. Mind you the hubs are locked in but still in 2wd. After doing a little bit of reading some were saying this is a sign of bad needle bearings and not the entire hub.
I haven't jacked up the tire and checked typical movement in a bad wheel bearing. I know my way around vehicles and 4x4's pretty well...
View 3 Replies
My 2000 SD has a brake line that rusted through. The one that runs along the drivers side frame rail. So I need to get new line to replace it. Since I am nowhere near my truck right now, what is the size of the steel line?
View 6 Replies
Is there a way to change the bulb without removing the grill and headlight? Seems like a lot of work to replace a bulb. 2013 F350....
View 3 Replies
I just realized my driver's side front leaf spring on my 2002 F250 has snapped. I checked the weight sticker on my truck and it weighs 5200lbs in the front. My question is the heaviest springs I found only support 2630lbs a piece, so being a 7.3 is 5200lbs a correct weight for the front of this truck? also why would Ford make springs that support only 60lbs more than the front weight? Hell I weight more than 60lbs.... Did I snap the damn thing just by climbing into the cab?!?!
View 6 Replies
Cat like noises coming from front driver side tire .. honestly sounds like a cat ..it gets louder the faster I go ... what it could be ?
View 7 Replies
Here's the deal. I have a 2001 F250 4x4 and I am getting a noise in the front drivers side wheel. The noise is not a grind or clunk, but its like a u-joint is rubbing inside an empty cylinder kind of. Anyways, it seems like it does it only with small bumps. I took off my oem hubs and re-installed them and the noise went away for about a week. Now I replaced them with manual locking hubs and the noise is back. One other thing I notice is if i put the switch to 4x4 the noise goes away. I checked all major components for the steering and suspension and nothing was loose. The front end is tight. Is there anything inside the axle that would cause this? I dont know what to check for anymore. Where else to check?
View 4 Replies
