Ford Super Duty (1999-2016) :: Slight Squealing Noise From Pulley When Truck Started
Mar 27, 2016
So a few months ago I would occasionally hear what appeared to be a slight squealing noise from a pulley when I started my truck. It was very intermittent, so I didn't think much of it.
After a few weeks, I realized I was only hearing it on colder mornings - it would also go away rather quickly. I bought a mechanic's stethoscope, and figured I'd get to it on a slow day.
Today, I finally broke out the scope and tried to figure out the source. Didn't really find any pulleys making noise, and I did notice that when I shut the truck off, it squeaks for a second or two as it comes to a complete stop.
My dream of finding a bad pulley or perhaps a power steering pump was crushed. I had hoped to do a little Easter wrenching and put this noise to rest. So, I did what any good mechanic would do - I Googled the issue.
I'm reading that it could be the belt. Certainly wouldn't bother me too much as that is an easy fix. The belt isn't too old - about 4 years and 20 - 30K on it.
I took a few pics of the belt and can take a video of start/stop ....
View 7 Replies
Advertisement
So When driving around I'm hearing this squealing almost chirping noise and it sounds like its coming from the rear of the Truck. I greased the bushings and leafs but that didn't fix it, to me it sounds like a rotating noise. Don't think it's the brakes cause it makes the noise when driving not stop.
Also, a bad alternator would make noise while driving over 40+mph, like a loud whistle?
Drive a 2012 F250 6.2L 19k miles
View 11 Replies
Tried using the search function without much luck. My brakes started squealing so I know it's time to replace. I use my 2wd 250 truck for work mainly and it has some weight on it. Most of my driving is stop and go. I use it to tow my Jeep maybe 3 times a year as well.
What are the best pads to go with? From what little I found using the search function it seems Hawk LTS or OEM from the dealer, not Motorcraft from the parts store.
View 7 Replies
I have a 99 F350 with a V10. I just replaced all the spark plugs and a bad coil which solved the very bad misfire I had going on. I also just changed the fuel pump and fuel filter.
When I start the truck, it idles just fine, nice and smooth. After sitting there for a short bit, maybe a couple minutes, it starts to idle rough, not so rough that it's about to shut off, just a little rough. This lasts maybe a minute and then goes back to nice and smooth and stays that way.
I've thought maybe the EGR valve or Idle air control valve but I'm not sure if I'm way off or sort of close.
View 1 Replies
2005 F-350 6L diesel .... Put new batteries in it a week ago.
Been running good then the radio quit a couple of times. It came back on after truck was restarted. This morning I go to town and the battery light comes on. I stopped and started about 5 times and on the 6th it wouldn't start.
I got a boost and started home it , started to try and quit when I was almost home. Was so dead the power windows wouldn't even work. Have it on the battery charger now and it starts right up but the battery light is still on and the ABS light is on.
View 6 Replies
Well shoot, not even 120k on the odo and I've had my first major problem with the truck, and the one thing I hoped wouldn't be an issue, especially since I don't work my truck hard and 95% is driving unloaded highway as a daily driver.
Last time I drove it coming home from grocery store there was a big racket from down under (transmission area). It instantly didnt feel right - there was a slight drag even when the clutch was in, but rolled fine when I pulled it out of gear entirely. Was VERY difficult to go into first gear. Other gears shifted ok but some of them felt hard too. Would not go into reverse at all!. Slight bit of clinking noises every time I started from a stop, but made it home ok and things seemed to ease up as I went. Today, seems to be shifting fine, reverse works and everything.
Now for several years I've had a noise that I couldn't figure out. I am guessing it's related because it sounded like was coming from tranny area. Often, when starting out from a stop, there was a bit of clinking noise like a couple tin pie pans rattling together just as the clutch started to go. I kept thinking it was loose heat shield or something clanking just under the initial vibration of getting going. Never did find anything loose. I'm guessing it's internal.
I've called a couple local shops and so far no one wants to mess with it. Dam this sucks i hoped the MT would be more reliable, not the first thing to go. I myself have never messed with any aspect of a transmission, though I not opposed to learn however I was hoping to take this on an out of state trip end of May, and I'm not going to have much any free time between now and then.
View 9 Replies
The truck is in my Sig 01 F250 5.4
Just got back from a long trip with it. Parked it for 3 days, all was running fine. Went to dinner Sat night and all was great, left the restaurant and as soon as I started the engine I noticed a slight vibration. As soon as I hit 42 miles per hour, it started shaking pretty good. I pulled over and checked under the truck to make sure I did not have anything I was not supposed to hanging down.
Driveshaft looked good, nothing leaking from rear end or tranny. When it does vibrate, the Tach shows the unhappiness as well. This a.m. driving to work it was vibrating at all speeds and shifting was very rough, had a hard time deciding if it wanted to be in second or third gear. I don't think this is drive train issue... When it shutters and sputters at 40ish MPH, its almost like it loses power and I have to let off the gas. and then under power it shakes badly.
I had the super chip settings for performance tow when this started and then I changed it back to stock settings, thinking it might work, which it only got worse. Changing the settings with the Superchip you have to disable the fuel system and I do this by pulling the fuel pump fuse under the hood in the power distro box.
I think the ujoints are still good, the oil and tranny fluid are spot on. Hubs are locked but in 2WD. Had all the front end replaced 15K miles ago. Brand new tires and wheels in Sept, front end alignment done at same time, front brakes were 90% and rear brakes at 20%.
View 10 Replies
I have a 99 f250 4x4 super duty. Just started getting a loud squealing noise off and on in the front end. Changed the ujoints and axle seals on both sides. They where all in bad shape. It still makes the noise off and on while in 2wd. If I lock the hubs in it doesn't. What it could be ?
View 14 Replies
So I went to start the truck this morning around 8:00 and it was 7 degrees outside, when the truck started the oil light came on and oil gauge was on low? So I turned it off right away. few hours later I tried it again and still nothing I thought maybe the oil was frozen. After I started the truck the oil was higher on the dipstick so I am assuming the oil pump is functional. What could be causing this? Could it be the the gauge is not working? The truck is a 2000 F-350 V-8 5.4 gas. I'm hoping it is something simple I am suppose to work this afternoon
View 14 Replies
I replaced a rear rusted brake line a couple of years ago. It rusted where the line met the bracket. I'd never done this before but bought a flare (flaring?) tool and fixed it.
This week the longer line that runs down the length of the truck started leaking. It looks like the line was once held in place by a small bracket just in front of the rear wheel but it wasn't in that bracket anymore. I guess it rubbed against the metal and water/sand rusted it out.
A local garage said they'd need to drop the fuel tank and estimated that it would be several hours (and hundreds of dollars) to do the job. It looks like I might be able to cut the old one out and then fish the new line up through there and replace it.
Also, what is the diameter of the line? It is a 2004 F350. I can certainly cut it out first and then take a piece of it to the local auto parts place to get the replacement line.
View 9 Replies
2000 Excursion 4x4 v10 auto. Pulling the boat last weekend up the driveway from the lake and the truck started smoking under the hood at the top of the drive. Jump out and saw a fire under the pass floorboard. Go the hose and put it out in 30 sec. Thought i blew a trans line and it sprayed on the cat. Took it to the shop and he said lines are good it's not leaking. He said it is possible that the trans over heated and built up pressure and blew it out past the front seal.? What happened or how to prevent it from happening again?
View 13 Replies
I had a can of fuel at home that had been siting around a while but I put it in my 02 F350 with the 7.3. hind site being 20/20 I shouldn't have done that. The truck only made it about 2 miles then started chugging and eventually quit. So I pulled the truck home and this is what I have done so far. I assumed that I had bad fuel so I started with a new fuel filter. I did notice that the fuel in the bowl was a milky white color. Not sure what that means. But the new filter did not work as the truck will not start. So after reading some other posts I decided to drop the fuel tank and clean everything.
I did that including cleaning out the 2 screens in the fuel pick up. After re installing the tank I put new clean fuel in the tank and primed the truck. But before starting it I drained the first amount of fuel out of the filter bowl just to make sure I got all of the bad fuel out of the lines. So after doing this I put a new filter in and primed the motor again. I appear to be getting good fuel pressure and the fuel looks very clean now at the bowl. But the truck does not even attempt to start. It turns over just fine but will not start. Some advice I can get before I have it towed to a shop. Also, the truck currently has 305,000 on it and has run great up till now.
View 5 Replies
Question, my truck started to have a miss under normal acceleration, when I really get on it, it clears up? I also noticed a bad sulfer smell at idle. Im thinking the cat is possibly plugged? Truck had 172000ish on it, and the cat is original. I did do a big tune up this past fall, new plugs, coil packs, air and fuel filter. Should I put a new cat on it? And a new oxygen sensor?
View 9 Replies
All week the truck was acting like the clutch was slight depressed when first taking off and then today i was driving and the underside of truck started smoking like crazy and slowly lost all the gears could put it in any gear and nothing just was acting like it was being revved. does this mean clutch is bad?
View 10 Replies
2002 5.4 super duty. My truck had started to ping, and knock worse over time. I did some research on this site, and I decided to remove my K&N air filter. Replace it with a traditional paper filter. Then I cleaned my mass air flow sensor. The results were great, no more knock and ping.I will check the MPG next to see if I get any improvements.
View 1 Replies
I have an 03 with a 6.0 diesel, going down the road and started losing power and then died. Won't start, and I don't have a scan gauge. Several sources said ipr valve, and from videos on youtube I thought may be a good place to start. I bought a socket and pulled the valve, to check the screen. There is no screen whatsoever on the ipr. The oils clean, as I had changed it about 200 miles ago, and I ran a magnet in the hole looking for a screen, couldn't find anything so I used my fluid pump in the hole. No trash, screen or anything. Do some ipr valves not have screens? What would be my next step??
View 2 Replies
Having an issue w/ my 00 550. When I lock in the hubs there is instantly a noise, More of a squealing then a grinding. The truck goes in and out of 4x4 no problem and the noise is there locked in 4x4 and not locked in, as long as the hubs are locked in. I can't tell if the noise is coming from the 4x4 driveshaft but there is no noticeable play in the u-joints or the u-joints in the front axle. I did notice when I spin the 4x4 shaft by hand the passenger side joint spins slower then the driver, not sure if that's normal or could be the problem.
View 2 Replies
2001 F450/6.8 gasser. Auto trans. This strange thing just appeared from nowhere. Start the truck, put it gear. As soon as the truck starts to roll, the chime begins to sound. If I continue on, it'll beep 80 or 90 times before stopping. As soon as brakes are applied and the wheels stop turning, chime disappears. Happens in forward or reverse. No lights appear in the cluster. A check with an Actron scanner shows no codes or MIL. Seat belts are buckled.
View 4 Replies
Just noticed today, while taking slight right turns 20-40MPH, I get a really loud and angry chirping sounds? Its only right turns...It sounds like a forest of angry crickets.
View 4 Replies
Bought a 2014 SD 4x4 in December of 2013 and this is the second time the big girl has been to the shop with A/C problems. First time it was the evaporator about three or four months ago. During the last few weeks of the summer I began to smell something strange (like band-aids) when the A/C was on and it lingered until the next re-entry. ALso, began to hear a slight hissing noise when the compressor was kicking in and out. They replaced the evaporator, smell remained as they said it was the refrigerant I was smelling. About two or three weeks ago the smell got slightly "larger", and last weekend she would not cool. This is the fourth time shes been to the shop with other problems such as the My Touch system..............
View 7 Replies
I am not sure which it is but I cannot turn the pulley by hand. How do you tell if the pulley is bad or the whole compressor? I went out to start the truck and it wouldn't start. It died so I restarted it and then I seen the smoke from the front of the truck. I opened the hood and the flipping belt was just hanging there. Is there a way to just bypass the unit for now? I wont be needing the AC till summer and that is several months away.
View 3 Replies
