My 2011 F350 is not engaging 4wheel drive from the dash switch. When I turn it to either hi or lo it says "shift in process" but no 4 WD. It will engage manually from the hub lock, no problem. I know very little about 4wheel drive but am otherwise mechanically knowledgeable.
View 5 RepliesWhen I shift into 4Lo I get no 4 wheel drive. 4Hi works. Did have a/c redirect to defrost a couple of times. I remember something about the air redirecting having something to do with not having 4x4 but don't know just what it was.
View 8 RepliesI recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
2004 Ford F250 CC 4x4 6.0L
Took the family down to the beach today. Had some tough sand to get across in a few areas to move away from the crowds. Got a little dicey and the truck got stuck in 2WD. Switched to 4WD but back tires kept spinning. Couldn't figure out why and the truck started to dig deeper in the sand. Got a little nervous and I didn't want to start the day off with having to get pulled out.
Got out of the truck, locked the hubs in manually and I was out, no problem. Left the hubs locked until we left the beach and back on pavement.
What might be the problem and why the "shift on the fly" switch on the dash didn't seem to engage the 4WD? I even tried to switch into 4L and back to 4H (truck in neutral, break pedal compressed) and still no workie. Only manually locking the hubs would engage the 4WD.
I have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesI have a 2001 F350 7.3 4WD that does not want to shift into drive. When you shift to drive you can feel a slight difference in the trans but it will not move, it will rev freely but not move. If I shift it up and down it will engage after a lag period ranging from 10-15 seconds up to several minutes. Reverse is ok and after forward engages it appears to work as it should, shifts ok through the gears. I don't have much experience working on automatics.
View 4 RepliesI have a 93 f250 4x4 with a 5.8 liter with 69 thousand miles.. the problem I'm having Is if I put It in drive it won't shift out of first but if I manually shift it from 1st to 2nd to drive it works but shifts very hard. Sometimes it will shift in drive but It shifts really hard. I don't know what It could be. We just put the transmisson back into the truck due to having to change a broken flywheel. It just don't Seem like it has any power...
View 5 RepliesI have a 08 6.4l F250SD. At 127k miles, it has been a great truck. All service has been performed by dealer. When I shift from Park into drive there is a 3-5 second delay, and when it drops into drive the truck rocks. Once driving there are no shift issues. Into reverse there are no issues.
View 14 RepliesChecked the EOF vacuum lines and pump but still have a problem. The EOF works and locks the hubs when I switch to 4x4 high, Easy to feel when you turn the wheels but it will not go into low. The light on the dash does not light up the word "low".
View 1 RepliesI need to solve tranny problem, it started out a while back, would not shift back into drive after stopping at stop sign (after driving fine for about 20 miles) thought maybe dirty filter so did fluid and filter change seemed to work for a while then started again noticed it was mostly after using cruise control, but u joints were very bad, so replaced 2 of the 3 and worked fine for about a thousand highway miles, then got really bad. Now when I check the tranny fluid cold and /or hot it is way up on the dipstick. Took to ford dealer in ladoga, lied and said no speed sensor codes, but list on the paper he gave me had all kinds of abs and a p500 code.
View 9 Replies1. Why does my front end hop when only turning right in 4 wheel drive?
2. O nly one of my back tires spin, so does that mean that when I put it in 4 wheel drive I only have 3 tires spinning?
oh I got a 2001 xl 5.4 f250 and is this normal
My 2009 F-350 4x4 has a front wheel option of Auto or Lock ; I think I understand the Auto option but under what circumstances would I lock the hubs and is it safe to leave them in the Lock mode when traveling on the highway?
View 5 RepliesOriginally it would light up on the dash, the hubs would lock, but the transfer case would not shift in to 4 wheel. Followed the troubleshooting I've found, was receiving power at the connection on the shift motor but it was not turning.
So I went and bought a new motor, installed it, still wouldn't turn. (with the motor off the transfer case but electrically connected). So I found a few more replies about the relays, swapped them, nothing.
Removed the covers and manually flipped the connection, nothing. Now my hubs are locked, transfer case is not, and I get nothing when I change the switch on the dash. (no lights, no hub click shift, no 4 low, nada). All the fuses are good, just doesn't work.
I have a 2008 for 250 6.4 powerstroke. Issue I am having is occasionally when I shift from drive to reserve it will slam when I shift to reverse. It is an intermittent issue. What causes this and what to do?
View 1 RepliesI have just switched from GM to Ford and have a new F250 4x4 XLT. I am wondering how to engage 4 wheel drive correctly. I have the manual shifter and the manual lock hubs. However during my test drive I shifted the lever into 4H and 4L and it seemed to engage just fine. Do I need to lock my hubs as well? Or if im just in a wet spot can i just shift into 4h without locking my hubs? I know if I am in anything serious I need to lock the hubs. I just want to be sure before I get into a tricky situation. My 02 GM all i had to do was push a button and it shifted automatically.
View 7 RepliesI have a 2001 F350 with a7.3 power stroke, 6 speed manual with manual t case and hubs. I have a bad grinding noise when in 2 wheel drive. Similar sound as if you are trying to shift t case into 4 wheel drive too slowly. The grinding is constant in 2 wheel drive, but if I shift it into 4 wheel drive, the noise completely goes away. I have been driving around in 4 wheel drive (T case only, manual hubs not locked) for the past 2 days. If I shift back into 2 wheel drive, a constant terrible grinding noise returns. What could be wrong, and why it goes away in 4 wheel drive?????
View 3 RepliesLove my 03 lariat Super Duty, King Ranch. Just found out 4 wheel drive is not working. Checked fuses, next going to look at the vacuum system, make sure its working. New to the Diesels but going to work at it and learn at the same time. 2003 F-250 4x4 ....
View 5 RepliesI have a 2006 F250 Super Duty w/ turbo Diesel. Took to dealership for "hopping" feeling when turning sharp. Was told that 4 wheel drive solenoid was bad. Where this solenoid is located? I know I can fix but want to know where it is located.
View 6 RepliesMy F350 4x4 won't go into 4 wheel drive unless I get out and take them out of auto and put them in locked position and when I have it in lock mode it seams to work like it's in auto mode, when I put the switch on the dash in 2wd, it seams like it's only driving the back wheels....
View 14 RepliesI recently picked up a '99 F250 Super Duty with the 6.8L V10 for a song.
The 4 wheel drive hubs are not working with the vacuum. If I use the manual lock on the hubs all is well. I ordered the Innova 31703 CarScan OBD2 + OBD1/ABS/SRS Scan Tool. It says it does Trans codes. I am hoping it will cover the 4 wheel drive too.
Maybe related, the heat is always on. Meaning I feel heat at my feet when the temp dial is cold and fan is off. I can't find the heater control valve to check the vacuum line.
I have a 2001 f250 7.3 powerstroke it is an automatic. It has the switch on the dash to engage the 4 wheel drive. When I turn the switch nothing happens.. no lights come on or anything. it has warren locking hubs. What my problem is???
View 2 Replies