Ford Super Duty (1999-2016) :: Safe To Drive Without Lock Hubs?
Jan 29, 2016
So after eight years my Warn premium hubs have taken a crap and developed major play internally. After speaking to Warn warrenty department and sending videos they will replace them according to the lifetime limited warranty. Problem is they sill not send out new ones until they receive the old ones, so I was told from time i remove mine and send them back and get the new ones it will be two weeks maybe a few days more, there is no snow in the extended forcast and im wondering what damage could occur with me funning the truck everday to work etc with the stub shafts just hanging there?
View 14 Replies
Advertisement
I just purchased an F-350 with manual locking hubs. I am unsure if I can keep these locked in for part time four wheel driving or I need to unlock them each time I go back to two wheel drive?
View 6 Replies
I have a 2010 F250 with 154000km (96000 miles) that we bought last week. When I was looking it over during the purchase I noticed the front axle didn't lockup in "auto", in manual lock it seemed fine so I figured vacuum leak or something like that. Yesterday morning I was in the yard and got a little hung up in snow drifts so just got out, locked the hubs and switched to 4x4 and I think the front end didn't engage at all.
So later on I had it in the shop installing the two way radio and decided to check the front end out a little more thoroughly. Vacuum lines seem fine, hubs turn fine but I notice the axle shafts both move up and down almost a quarter inch, that seems excessively loose to me. I've been doing some research on the internet and it appears the front hubs are serviced as a unit, also some information seems to point to needle bearings within the actual locking hub mechanism itself?
So the questions:
1. Does that front axle shaft seem excessive? What are the specs?
2. Can I replace bearings and seals only or do these units come only as assemblies? Inner hub, outer hub units? Wheel bearings seem fine.
3. With that much play is there a chance the outer axle shafts are worn also?
View 14 Replies
Had to make a sharp circular turn last night in a parking lot, with the steering turned to full-lock...noticed a very audible clunking or clicking noise during the turn...went away after full-lock turning was released. My hubs are locked in...but I was told there was no issue with leaving them locked in, even during the summer. And there shouldn't be...4x4 disengaged, of course. Must have been the u-joints clicking / clunking? Problem?
View 5 Replies
My 2009 F-350 4x4 has a front wheel option of Auto or Lock ; I think I understand the Auto option but under what circumstances would I lock the hubs and is it safe to leave them in the Lock mode when traveling on the highway?
View 5 Replies
2001 F-250 7.3. The auto lock hubs are not working on the truck lock hubs in and all works fine. First thought is the vacuum system has a leak or something of the sort. Had truck at the shop they are telling me the GEM module controls the vacuum to engage the auto hubs and the signal is not coming from the GEM and it need to be replaced. It was the GEM causing the problem.
View 6 Replies
I noticed that my 4WD is only working now when I manually lock the hubs in (they have that options!), and the air blows out the defroster when I shift, so it looks like I have a vacuum leak. Where are the typical leak points on a 2006 F250? What's the best way to confirm a leak (other than just replacing all of the hose)?
View 2 Replies
My 2005 has the ESOF system which has worked flawlessly. Recently I had upper and lower ball joints done and after that repair I had no auto locking hubs. ( independent shop messed up seal install ) they redid the job and it now seems like my front hubs are locking automatically because I am getting binding while turning. So this is the problem.. the front wheels do not "pull" only the rear wheels spin. If I manually lock the hubs I have 4x4 and can get out of being nearly stuck and everything works normally. What is wrong here? Does the shop need to redo the job again?
View 2 Replies
My F350 4x4 won't go into 4 wheel drive unless I get out and take them out of auto and put them in locked position and when I have it in lock mode it seams to work like it's in auto mode, when I put the switch on the dash in 2wd, it seams like it's only driving the back wheels....
View 14 Replies
I recently picked up a '99 F250 Super Duty with the 6.8L V10 for a song.
The 4 wheel drive hubs are not working with the vacuum. If I use the manual lock on the hubs all is well. I ordered the Innova 31703 CarScan OBD2 + OBD1/ABS/SRS Scan Tool. It says it does Trans codes. I am hoping it will cover the 4 wheel drive too.
Maybe related, the heat is always on. Meaning I feel heat at my feet when the temp dial is cold and fan is off. I can't find the heater control valve to check the vacuum line.
View 14 Replies
I recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
View 2 Replies
We got a ton of snow dumped on us today and for some reason my 4WD has decided not to work this year. I have a 2000 F250 4WD Triton V10. The hubs click into the lock position and the dial on the dash lights up 4x4 but I am definitively not engaging into 4WD. I'm pissed because this is specifically the reason i bought a 4WD and it's failing me. I can't find a fuse panel diagram to save my life however all the fuses in the interior of truck look to be fine.
View 3 Replies
Just bought a 2002 F-250. Truck came with 18" Rims with 275/70/18 tires. The turning radius is awful, almost unsafe. The stock rim and tire size should be 16" rims with approximately 265/75/16 tires. Would the larger rims have that big of an effect on turning radius? I have owned two 2006 F-250's, and they turned nothing like this truck. I have not really gotten into the front end to see if the stops have been adjusted and/or if the tires are hitting.
View 10 Replies
Its a 2016 F-250, 6.2L gas truck with the electronic shift on the fly transfer case.
I have put right at 22,000 miles on it like this, frequently at 70-80 mph.
What are the odds I have damaged it and is there anything I should do now that I discovered it - other than put them both in "AUTO".
Truck has been to the dealer twice and not once was this noticed. They blamed the squealing on the brakes which I knew it wasn't.
View 14 Replies
Back in March while still plowing, my auto locking hubs wouldn't stay engaged. After talking to the local Ford service shop they told me that it was moisture in the vaccum lines and that it had frozen. They told me to manually lock the hubs and bring it in to be repaired when I had time. I made a appointment in the middle of May and finally got it in last week. Now the hubs are seized in the locked position and they will not warranty the work or parts because they say it was caused by the salt from our roads. Does this sound right?
View 5 Replies
I've read many posts about ESOF and fault vacuum lines and how that will prevent 4x4 from engaging. I experienced a different problem this past weekend. Here's the situation...
Was about 1.5hr drive up to the mountains. Outside temp when we left the house: 10F. Outside temp when we arrived at destination: 9F. Quite a bit of road grime on the way up from sand, slush, and that magnesium chloride (or whatever they hell they put on the roads in an attempt to keep it from freezing). 4x4 worked fine on the way up. 4x4 light on dash was on, and I KNOW I could not have climbed the snow-covered forest roads without being in 4x4. Also, I could hear and feel the front hubs turning.
On the way home, once I got to where the roads were sufficiently ice free, I turned the dial on the dash back to 2WD. 4x4 light goes out. But I can hear and feel the front hubs are still turning. Toggled the switch back and forth a few times. 4x4 light would come and go with the toggled switch. But the hubs didn't disengage.
When I got back into town (outside temp now about 5), we stopped at a red light and I toggled the switch again. This time, the hubs disengaged. Is this a sign of bad vacuum? Or more an indication of faulty hubs??
View 7 Replies
My hubs will not lock when put into 4x4. I disconnected all lines from the solenoid to both hubs and tested them for leaks... All good there. I put a gauge on the lines at both hubs one at a time while the other is still connected and get no reading when switched into 4x4. I checked for vacuum right out of the solenoid, and I get 2inHg when switched into 4x.
The vacuum pump kicks on every time I start the truck, even if I just shut it off and re-start right away. There is no delay when switching my ac/heater controls to different settings or vent locations. So I know there is vacuum. How much vacuum I should be getting out of the solenoid to the hubs?
2004 F350 6.0L....
View 3 Replies
I have a 01 f250 v10 4x4 ... My stock hubs squeak non stop when they are engaged. I want to get a set of warns.
I am going down to napa tomorrow, looking for a detailed link, or instructions of how to install these things? i have searched but just keep coming up with people raving about how great warn hubs are!
Do I need any special tools, do I need to grease the new ones before installing?
View 14 Replies
I just got a 99 F250 PSD, it had not been in 4wd in a while, now the hubs won't unlock.
My 01 F250 seemed to have strictly manual hubs. Turn right to lock, left to unlock. They may have been aftermarket, but on by the PO. Do I need to put some new Warns on the 99? Or can I lube then up and get them functional.
View 14 Replies
I just ordered '00 F250 SC 4x4 SWB XLT with the factory standard manual hubs. The hubs show up on the vehicle order confirmation as code "21M MAN LOCKING HUB". I can't find this code in the ordering guides anywhere but kbb.com shows this code as "Manual hubs delete. Required with 213 shift-on-the-fly". I want the manual hubs. I think ##### is incorrect. For my piece of mind, could someone who has also ordered the factory standard manual hubs verify that the code is indeed 21M. And for those who ordered shift-on-the-fly, could you verify that 21M does NOT show up on your order confirmation...
View 8 Replies
inside round thing with 4 notches in it is a smaller diameter than the new hubs. Will theystill work?
View 6 Replies
