Ford Super Duty (1999-2016) :: Rear Bumper With Exhaust Cut Outs
Aug 13, 2016
While trying to remain positive regarding my current truck fiasco, I was thinking about future mods. I really like the way Dodge has the exhaust cut outs in the bumper and was wondering if anything like that exists for our trucks?
View 3 Replies
Advertisement
my rear bumper is pretty much eaten up, too.
How difficult is this to replace?
Good source for rear bumpers? Just something stock; don't need anything wild, crazy, lighted, etc.
It's a work/hunting/fishing/hauling truck. That's all.
View 1 Replies
Ok I have a 2001 f250 SD with 7.3 and my rear bumper is dented and badly and warped. The steel frame mounting part of it is straight and fine. I found a "kit" on eBay that has just the end caps and plastic top cap for a 2008+ style trucks. Would those caps and plastic fit on my frame mounted section (what the actual name for the part that the chrome bumper actually screws into that mounts it to frame) ?
View 1 Replies
Adding red/white reflective tape to the rear of superduty? Pros, cons, legal etc?
View 14 Replies
Installing a back up camera and need to locate reverse lights on driver's side at rear bumper. What color wire is for the reverse lights on a 2003 F-350 (truck in my sig)?
View 4 Replies
Do f150 bumper is the same as my 03 F250?
View 5 Replies
On the 99-07 front bumper i would like to add driving lights in the bumper under the headlights something like the 11 up bumpers have...
Looking for a light and housing that possibly could be installed with out having to re chrome, so it could have a bezel to cover cut edge of bumper...
View 4 Replies
I bent my front bumper. Every time I look on amazon or ebay , when I put in my year, model, engine, it says their bumper won't fit. Mine has the 3 rectangular openings, 2 have the holes for mounting and tow hooks. It is chrome with the gray plastic or rubber bottom.Xlt. Also what part is the valance?
View 7 Replies
Will a bumper off a 2008 F350 fit on my 2006 F350?
View 7 Replies
I noticed today my ranch hand bumped is hitting my fenders, when I originally installed it there was about a 1/2" gap.
All the bolts are tight, however it appears the mount that's attached to the frame is flexing and becoming weak as I can grab the bumper and rock it when it used to be rock solid.
Is there anything I can buy that will reinforce the bumper mounts that are connected to the frame to support this bumper???
Right now it's bolted up with 4 bolts on each side and no additional hardware.
View 3 Replies
I got a 2014 F250 SD w/ 6.7 diesel. Since if owned the truck the front bumper has slowly started to sag at both driver and passenger side. Dealer says there is no adjustments for it.
View 14 Replies
Do a 2014 f350 front bumper will fit on a 2001 f350? Wanting to know if the bolt holes and body lines will match up? I put a 2014 rear bumper on and it bolted right up.
View 8 Replies
i've done some searching but haven't found any how-to's or instructions on how to remove the front bumper on my 06 f250. Any link on how to do it?
View 2 Replies
I would like to install some driving lights behind the front bumper of my 2005 Super Duty, I was going to drill two 5" holes and than weld in some 5" pipe from the behind the bumper and attach some 5" KC driving lights to it. Would a hole saw work for this or is a bumper to thick? I was looking at DeWalt or Lenox hole saws their bi-metal. I know that I have to drill slow and I was going to use cutting fluid. I could use my drill press but I think I would have to figure how to clamp a bumper to the table. Then I am going to grind/sand the chrome off and paint it black. I will be taking the bumper off doing all of this.
View 4 Replies
I am installing a set on a '12 F350 for a customer. I already had to go buy an additional hardware in order to get the back bumper on correctly...and now I'm looking at the front bumper and I swear I don't have the parts I need to install it. It appears to be missing some brackets. There were NO instructions with them (apparently a chronic problem with Road Armor) and I can't possibly imagine it bolting to the flimsy brackets that hold the factory bumper (fairing would be a better word for it) in place.
View 6 Replies
Any good way to install and mount a light bar without drilling into the front bumper or grill? I have a 32" LED bar I want to mount between the top of the bumper and bottom of the grill, but the mounts aren't ideal for where I want to put the light.
View 9 Replies
The exhaust system from the downpipe back was stolen off this auction truck I bought, so I bought an even worse truck for parts but I'm struggling to get the exhaust off. Is there a trick to it? Does it come out going forward over the rear axle or pull out from the back? Should I just cut it and have a shop weld it back?
View 8 Replies
I am new to Super Dutys but i love them! Altho mine is not being so nice. It has the 5.4 in it. When its idling it has a stumble to its idle with a pop every now and then out the exhaust. It revs fine when its first started. If i pull out on to the road and start away easy its ok a slight miss but if i put the throttle down its just falls on its face. But if i get it up to cruising speed its ok as well. But even at cruising speed more then 1/8 throttle and it starts missing and falling on its face. What it could be? It smells like its running lean as well.
View 14 Replies
I own a 2001 F250, I bought a skid steer that weights 7000lbs and got a trailer that is 14,000lbs.
The truck was running fine, today was the first day I used it and I noticed by the end of the day I have oil dripping from my exhaust.
The dealership told me that the f250 is able to town that much weight, what caused it, as well as is it safe to continue to tow with it?
View 1 Replies
I have a early 2003 SD with the 5.4 triton. It has a oil leak on the passenger side, the oil blows back and gets on the exhaust.
I have been under the truck with the engine running looking at where the head meets the block and at where the valve cover meets the head and can not see a leak.
Sitting there running at idle it does not drip a drop off the engine but the entire underside of the truck is coated in oil.
I did notice that the depression around one of the upper valve cover bolts was filled with oil, I cleaned out the oil, let the truck run and it stays dry.
View 8 Replies
I plan on putting a catback exhaust on my 2016 F350 6.2 gas engine. I have always loved the sound of Flowmaster exhaust but over years have started to become slightly annoyed with the drone in the cab. Is there a exhaust system out there that is capable of sounding like Flowmaster but without the in cab drone.
View 2 Replies