My truck has factory tint on all 4 corners as well as the rear window. I do quite a bit of night driving and I'd like to remove the tint on the drivers window as well as the passenger window. Is this even possible? I fear the glass was 'smoked' when manufactured and going back to completely clear glass will require a totally new window.
View 10 RepliesMy factory radio will not work. The person who had the truck before me installed an after market radio and it works fine, but the factory radio will not power up when I plug it in...is the radio shot or is there a way to fix it.
View 1 RepliesI'm still fighting tow harness problems on my '01 F 250. I started by replacing the 7-way pig tail with a new one which didn't work. Then I undid all the butchering of the harness that was done previously. The factory harness had scotch locks all over it that were used to splice in a 6-way and a 7-way into the bed. I liquid taped all the nicks in the wires. Then I checked for power at the factory harness end where the pigtail plugs in. I have park/running lights, and one of the ports flashes for the left turn signal/flashers/stop lamps. I got rained on before I could check further up the wire. If I have no power to the wire further up is there another place to check?
View 2 RepliesIt is starting to get cold where I live in Idaho, 22 this morning, and when I use the factory remote start on my 2011 the heater is not coming on as the owners manual says it should.
View 6 RepliesOk, it's cold out... is there a way that I can use my factory key fob to lock and unlock the doors with the truck running? 2000 F350.
View 10 RepliesCan 2011 F250 factory 18" wheels fit on 2004 F250?
View 3 RepliesIs it possible to add the factory keyless entry without replacing the complete dash harness? I have an aftermarket unit I can add but I'd rather have oe if possible. Truck is an 2003 f250 v10.
View 1 Repliesto removing the bed from my F250, there are 4 screws is that all ? and how heavy is the bed is it possible that four people can remove that ?
View 13 RepliesI have the Ford plastic drop in bed liner, and being up in the salt belt in CT, i want to take it out just to see how things look under there. Dont want to be surprised later on if i keep waiting. How do you take this thing out? Just pull the sides out from under the bed rails? You dont have to take the plastic trim that goes on top of the bed sides off do you?
Also, i want to get rid of this thing soon. The best thing to replace the plastic liner? i dont want to just leave it metal, but my dad has had a spray in "rhino liner" in his 04 ranger since the day he bought it and it has held up great. so i am thinking something along that line. How much it would be to have a spray in liner installed?
I heard today that, to remove the engine, the cab has to be raised?
View 13 RepliesI got a new headlamp switch for my 2016 SD. I have the XL work truck with no fog lights. I recently added fog lights and an OEM fog light wire harness. I also got an OEM switch that pulls out to activate the fig lights because the stock switch in my truck operates the headlamps only. What I can't figure out is how to remove the switch.
Here's a photo of the new switch .....
2011 F250 with hood mounted windshield washer nozzle. How do I remove the nozzle? In a campground with basic tools.
View 6 RepliesRear-most connection before pumpkin, need to replace the U-Joint. I got the four bolts out at the flange but the shaft won't drop. I beat on the connection a bit, not enough to hurt though. What am I missing? How the heck do I get this apart and drop the shaft to replace the U-Joint???
View 9 RepliesI have a 2014 f250 with tailgate assist, How do I remove the tailgate from the truck?
View 14 RepliesWinter is around the corner and I would like to remove the chrome covers off of my 04 factory rims, the rims are rusting underneath the covers which is forcing my center caps to pop off randomly. Also I was going to get new winter tires so while they rims are off the tire i figured I would Paint them black to match better than the chrome. How to get them off easily? Also a good paint that wont chip easy when i paint them.
View 6 RepliesI have a 1999 F-250 super duty 7.3 4x4 and the rear drivers side axle seal is leaking. My question is how do I remove the axle shaft? my last truck a f150 had c clips in the diff that released the axle shaft but I did not see those on this truck. How to remove the axle shaft?
View 8 RepliesWhat size socket is used to remove a lug nut on a 2000 F350 4X4?
View 6 RepliesMy grandad passed away a few months back, and I'm about to get his truck ready to sell/trade for my grandmother. The truck is an 09 f150 with only 18k miles, but it's got a couple minor issues like soft brakes from sitting, I'll post those problems in the f150 section if i have any issues fixing. He liked to leave the extended cab windows cracked in the summer. Problem was, he would forget to raise them, sometimes weeks at a time. He was 88 and suffering from dementia. This leads me to my question : How do I QUICKLY get rid of the musky smell? I came home this evening, and went to put it in the garage, and the windows were fogged up from the inside, and it smells awful. The windows haven't been left down in at least 6 months. This sucks, because this truck is flawless other than this. Dad had put open boxes of baking soda in it, but it hasn't worked.
View 11 RepliesLong story short, ended up spilling a small cup of watered down paint in the bed. Of course some ran out the bottom as well but I'm most concerned with the bed. How to remove the paint? Since it was so diluted I figured it would wash right out at the car wash with high pressure.
View 6 RepliesNo special extraction tools are required, just a small jeweler screwdriver.
Push the screwdriver into the back of the connector, to push the Red terminal locking bar loose, then extract from the front.
How to remove the side mirrors (top and bottom) on my 2016 F250? I don't need to remove the entire assembly (off the door), just need to get behind the mirrors themselves.
View 5 Replies