Ford Super Duty (1999-2016) :: P2196 - O2 Switch Sensor Indicates Rich
Dec 12, 2014
2007 E450 Van. Dash light came on. OBD2 reader indicates: P2196 Ford - Lack of HO2S-11 Switch Sensor Indicates Rich
I need to find out which sensor to replace. It looks like I need to replace Bank 1, Sensor 1, but I am not sure where it is located. My guess it's located on the manifold, but I'm not sure if it's driver or passenger side.
A friend says, "Look in the owners manual for the van and find out which cylinder is cylinder number 1. Cylinder 1 is always on Bank 1."
The owner's manual has no indication of where cylinder one is located. I do not have a service manual.
I am not highly technical, but I do think I can replace the sensor myself, or at least I would like to give it a try.
View 3 Replies
Advertisement
2004 f350 sensor switch will now and then let me turn it "on", but turns itself off immediately. Has never worked since I owned truck.
View 1 Replies
2008, 5.4 liter, F250, with 6-speed manual transmission
My truck was running fine until I decided to clean my engine. I just wanted to remove the extra dust covering it, so I used a low pressure garden hose to wash away the dirt that had accumulated last winter and spring.
It started throwing codes like Fuel Rail pressure sensors, P0191, P0192. I had no power, and I could hardly drive the truck.
I figured I had some water in some connectors, so I checked around, but could not detect any moisture.
I kept driving it, and the problem got less severe. One warm summer day, I drove my truck for about an hour trip, and everything looked fine after this. Problem never came back.
I was even noticing that it was better on gas that ever before, I was doing 11liters/100km, in city driving.
Until one day (2 months later), I had to disconnect the battery to do some servicing on my truck (more that 30 minutes), and it started to run crappy again, having some piston misfire, throwing codes P2198 and P2196, (O2 sensors). No power, if I am very gentle on the gas pedal, I can manage it, but as soon as i try to accelerate, runs like crap, black smoke coming out of the exhaust.
The problem comes and goes, sometimes, the problem stops, and I can get going, no issues. Air filter is clean, even tried with no air filter, no differences., but it really sounds like bad air/fuel mixture.
View 2 Replies
My truck threw a check engine yesterday, P1151 and P1152. What could be the problem? 04 f350 with 5.4 with 142,xxx on her
View 14 Replies
What may be the issue with my truck. Drove earlier in the day and hauled trailer. Ran fine. Got it home and once I unloaded trailer and went to start up truck again it died a minute into backing up. I tried to restart and turns over but dies in 3-5 seconds. Tried again a few hours later and next morning and same thing.
Pulled code and came up P0172- Bank 1 running rich. I had replaced the Mass Air Flow sensor a few months ago. Since it was still under warranty I went and got a new one in case that was the issue, but didn't fix. When I try to start it smells like gas. Sounds like fuel pump is coming on fine. Checked air filter.
Of course is still hooked up to the trailer and in a tight spot in the yard at the moment so anything basic/inexpensive I can try myself first would be great.
View 1 Replies
2002 F-250 5.4l 4x4 ... I am getting a P0171 code only, with strong fuel smell. No P0174 code. So it has to be something effecting just the one bank? Sprayed engine with starting fluid, no charge in idle. Replaced upstream O2 sensor, no change. Truck was running fine, and then just started this all at once.
View 5 Replies
So I just replace my Cat. Converter with all new sensors in them. I just replaced my spark plugs. (I'm knocking out these check engine light problems) and I think I'm getting close to the root as to why these other parts went bad. Why my o2 sensor would be stuck on "lean" ....
View 5 Replies
My Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 Replies
Seems like my truck won't move at 4x4 when getting into and out of parkings. Combination of low speed and turning feels like I am fighting the truck and need to apply more power to get it moving and then there are strange noises.
Is this normal behavior from 4x4 system? I think it is but just want to make sure that constant switching between 4x4 and 2x4 is normal. I was just to AWD cars before that.
View 6 Replies
My truck was involved in an accident and required a replacement front axle be installed due to damage to the housing. The truck was in four wheel drive when my wife got T-boned and drove up over the median twice to avoid a head on. The shop that did the insurance work said they replace the axle with a low mileage used unit, but since then the hub switches aren't working correctly.
I have taken it to them 4+ times to look at the issue and I keep telling them that the driver's side hub switch won't release, but I keep getting it back with the same problem. The most recent fix they came up with was to replace switches and electrical components. I am thinking that a vacuum leak in the hub may be to blame. I am taking the truck back to them again this afternoon as the 1 year warranty on the repairs is up next week.
View 7 Replies
2005 Ford F250 5.4 ... Having problems with ignition switch or bus bar in that circuit being bad?
View 3 Replies
where do the wires from the cabin aux switches end up? Are any pre wired to outside of the cab (past the firewall?).
i was wanting to install a better back up light on an aux switch but don't want to deal with running thru firewall, etc.
View 2 Replies
I got a new headlamp switch for my 2016 SD. I have the XL work truck with no fog lights. I recently added fog lights and an OEM fog light wire harness. I also got an OEM switch that pulls out to activate the fig lights because the stock switch in my truck operates the headlamps only. What I can't figure out is how to remove the switch.
Here's a photo of the new switch .....
View 14 Replies
As I pulled in to park I slid only 3 or 4 inches and just kissed a snow bank, didn't even think anything of it. An hour later truck wouldn't start until I reset the inertia switch. Man that thing is sensitive!
View 13 Replies
Having trouble tracking down the problem with my 4wd. Its a 2003 6.0. My esof switch is not working. The 4wd light comes on when I start the truck but nothing after that. I checked fuses and the relays under the hood everything is good.
View 2 Replies
I have a E99 f250XLT 4X4 Crew Cab PSD.
I have been on this site for the better part of 2 hours searching for my switch problem to no end. Most everything I am pulling up has to do with the lock actuators. I have a switch on the drivers side that will not lock any of my doors. The passenger side switch will work just fine as well as the key fob. All of my actuators work for all 4 doors. No issues with the dome light or door ajar light staying on.
Here is what I have done so far:
I have taken the passenger door switch off and put it on the drivers side and it will not lock the doors.
I have bought a re-manufactured driver side door lock switch and installed it and it did not lock the doors.
I have taken a jumper wire and grounding a pin on the drivers side switch harness and can get the doors to unlock but i can't get it to lock.
Where and what color wires to look for in a harness at the door kick panel or anywhere I might look for a broken wire? It is really frustrating that I can not lock my doors without using my remote.
View 1 Replies
I've checked the fuses, the lights are on on the switches, but I have no power at the wires under the hood. I'm adding lights and would like to use those switches..
View 2 Replies
I have just bought a 2004 F-250 SuperDuty 6.0 Diesel with 98k miles from a Ford dealer (no warantee)...
Just after I drove it home I noticed the Tow/Haul mode switch was not working - no dashboard light and no transmission downshifting.
The dealer took the truck back in and kept it for 2 days, it came back working, they claimed to have replaced the gear shift lever. 500 miles later and the Tow Haul has failed again.
View 14 Replies
Just recently I started blowing PCM fuses (#19 in the fuse panel) After replacing lots of fuses, I finally figured out what was causing them to blow. I unhooked the overdrive switch, and no fuses blow. I can't see anywhere where the wire is chafed. Maybe it is chafed, and I can't see it or the switch is bad. Can the whole OD switch be replaced? If so, how??
View 13 Replies
On my 2008 SD F350 my number 1&2 settings on the fan don't work. Only 3&4. What's the problem? How do i fix it?
View 8 Replies
1999 F350 Crewcab 4x4 dually V10. Fan switch only works on High. All fuses and relays look Good. Is it a bad speed control switch? What can it be?
View 8 Replies
