I have a early 99 7.3, I have parked it for the winter an I had moved the truck the other day an have noticed it had leaked some oil, after looking for the source I found that it is leaking out of the #7 cylinder exhaust port. I know the oil is forsure in the manifolds usually burns off but now that it is not getting to operating temp it is staying a liquid. Where is this oil coming from?!!
View 4 RepliesWhats the best way to get at the driver side exhaust manifold? I have a leak and its tough to get at. Should I remove the tire and inner wheel well?
View 1 RepliesI have a 2005 f250 5.4 no mods. its got 120k and needs a wake up. the passengers side exhaust manifold is leaking to the point of fixing and would like to get some input before the big purchase. my question is, headers or new manifold, and what brands is preferred for both I really don't prefer one or the other i just want the best fix really. Changing coil pack and getting more performance out of them and if so what brand. I would like a boost in lower end acceleration and throttle response, like a programmer or such. and if so what brand once again.
View 10 RepliesThis is right beneath the drivers side exhaust manifold. Not sure what it is but it appears to be leaking oil. Tried to tighten it and it seems snug. Can it be the gasket has gone bad for whatever it is?
Truck is 02 SD, 7.3, 4x4, with 512k miles.
Not really leaking bad but if easy enough to fix why not. It also appears to be leaking on the same side cylinder bank back near the rear of the valve cover. Need to see if I can snug that up as well.
It's right in the center of the pic. It's a bolt going into some sort of fitting housing that ties into the back portion of the block. Ignore the coolant streaks on the coolant hose. This is the oil leak in the darker center of the pic.
I have a leak at the driver side exhaust manifold. Its a little tough getting at it to tell if its a lose bolt, crack or bad gasket. What would be the best way to get at this area? Should i remove the tire and wheel well or is their a better way. If i can get at it i may replace the manifold all together.
View 2 RepliesI got a 08 ford f450 sd in the shop with a cracked abd broken bolt in the driver's side exhaust manifold, any tips tricks on getting it out,I have everything loose but I can't for the life of me get the egr cooler out of the way to access the top bolts to the manifold so I can replace the manifold, or a link to a service manual would be great.
View 3 RepliesI think I have a clamp or something loose as i am dripping coolant from a black and silver hose/pipe on teh drivers side of the motor.
I can't see any clamps, well clamps i can recognize. how is this black pipe connected to the aluminum pipe? at that seam is where it's leaking.
04 f250, 5.4 ,90,000mi. Checked my oil today and saw this white flaky crap on the dipstick its salt, probably from a broken dipstick tube, probably broken at the manifold right where there was a huge deposit salt right on top. The manifold is leaking anyway I was hoping to wait till spring when everything dries out and warms up a little bit, but with salt getting into the engine I think I have to do it now. Is there any way to deflect moisture off the road away from the exhaust manifolds?
View 4 RepliesThe doors on my 2005 crew cab are leaking water. Its happened once before, I fixed it by resetting the main seal around the doors. Now this tropical storm had them leaking again. The rear doors are leaking from the top and getting the head liner wet, and the front left door is leaking a little bit onto the middle pillar Guage and down onto my leg.
Is it time for new door seals? My 01 has never had this problem so im not entirely sure what to do.
Should I attempt to replace the passenger side manifold with what I can get from Napa. I would rather pay 100 bucks for everything and do it myself. But, Im concerned about replacing the studs. From what I have read the studs seam to be the problems for most leaks on these vehicles. I have torque equip. and other tools to do the job. Just want others opinions about this project. How hard really is it? 1999 5.4L F250 SDuty....
View 14 RepliesI had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
I have a 2013 f250 6.2, I bought the truck brand new only have about 3000 miles on it and the other day I noticed that the drivers side front is lower then the passengers side front, the drivers side is about one inch lower, this doesn't seem right, also my drivers side front wheel seems to be pushed forward about one inch to the bumper that also doesn't seem right.
View 3 RepliesHave my oil leaking-passenger side head gasket replaced (along with the drivers side for preventative measures).
To ease my mind at such an expensive repair on a truck I just recently bought, I was wondering what else gets replaced with this repair.
Obviously the head gaskets along with head studs, coolant and oil, but anything else? valve cover gaskets? intake gasket?
On the F250 trucks, if I changed the mounting frame under the seat, will the passenger side seat fit on the drivers side? Basically, can I turn a passenger seat into a drivers seat?
View 4 RepliesHere's my problem while replacing brake pads i found that my axle has leaked fluid on the pss,side rear rotor and all over .. I been looking for any info on repairing it myself . I found Everything for every other truck just not for this truck.
It's 2003 F-250 w/5.4L all Stock rear axle has 12 bolts and gears are 7.73 ... I believe its a Dana 60. No tags or markings on the Axle to go by..
I live in the Freak-en woods here so i like to order all the right parts once and do over the weekend .. its my only ride so once apart im stuck here.... I did check the Vent Tube its fine..
So I've put about 1000 miles on my 03 F250 since buying it, and just the other day it's started leaking from the rear of the passenger head gasket. Enough to drip on the driveway and exhaust, and have some exhaust smell. 126,000 miles, 5.4
I've checked with my local ford dealer, and It also needs passenger exhaust manifold and studs, so the dealer price to tack that on would be a whole lot more too since there are already a couple studs broke. It would be best to get it done when the head is pulled.
I've checked with several local mechanics, and none of them are interested in pulling the head on this engine. That has me concerned about doing it myself too..especially since it fits in my garage with only a few inches to spare..
My 2000 f350 is leaking oil from a bolt on the passengers side valve cover. it is one of the bolts on top of the valve cover. Can I just remove the bolt and put a rubber washer under it or do I need a new valve cover?
View 2 RepliesI have a 2005 F350 XL Heavy Duty 6.0L truck that has 68,XXX miles. I recently changed the rear brake pads and about a week later the rear passenger side is leaking brake fluid. The fluid is slowly dripping from the bottom caliper bolt but i am not sure if there are seals in this area. the driver side is fine and the fluid is only leaking from the bottom caliper bolt not the top.
View 2 RepliesI just put new rims on my truck which are 18x9 with a -24 offset. I swapped my 35s over from my stock wheels (which they didn't rub at all). When I put my new wheels on, the drivers side rubs really bad but the passenger side doesn't rub at all! I'm extremely confused why this happens. I know negative offset will make the wheel rub weird. But why is it only happening on one side and not the other?
View 10 RepliesThe used 2004 F-350 I bought has developed a driver's side front end howl between 45 and 60 mph over the last 1000 miles. I tried all the standard stuff, rebalanced tires, rotated tires, put on a set of tires from a friend's F-350, replaced wheel bearings, replaced ball joints and nothing has worked.
View 7 RepliesMy drivers side armrest was broken when I bought it. Been searching for repair advise but have not found any. Instead of stopping so you can put your arm on it, it just falls down. I sorta wanted to see what I was getting into before taking it apart.
View 1 Replies