Ford Super Duty (1999-2016) :: Oil Leaking From Water Separator / Shaking In Reverse
Apr 30, 2017
2016 Powerstroke ... Bought the truck new and now with 17000km. 1st oil leaking from water separator. 2nd oil leak from what looks like the engine pan,and they have some O rings ordered for it. I have had either huge flares in all gears or slipping whatever you want to call it ? ford dealer finally acknowledged one year after me first telling them of this issue. Especially when the truck first driven in the morning never really fully engaged in gears,it has no torque and all revs. So just got it back from the dealer and its something of a firmer shift but still flares.
But also now shakes violently in reverse since i got the truck back from them. Don't really want to put a tuner on it to get shift firm enough to be practical but voiding warranty. i like the low down torque this motor produces,and in manual mode works well but still flares some. Horrible in auto no torque like driving an old beater with a worn out clutch. They replaced shift D and E solenoid but I don't think this it the issue with my transmission. im thinking of taking the truck to a tranny shop for diagnosis. Could it be line pressure ?
View 5 Replies
Advertisement
We have been having near zero temps for several days and it occurred to me that there may be some amount of water in the water separator in the rail mounted fuel filter (not enough to send a message, but maybe some amount). I only have 3,000 miles on the truck. So, just wondering if a small amount of water is going to hurt anything in the filter or filter housing if it freezes? Should I drain the filter in freezing weather even though enough water hasn't collected enough to activate a message?
View 6 Replies
So today. I filled my truck full of diesel. when I started it back up, it through the wrench light plus drain water separator. What it could be I have a loss in power. wont get over 45mph.
View 2 Replies
Well I just bought a 2011F250 6.7 on Friday. The truck has 42000 miles when I picked it up and now has almost 42800 4 days later. I love the truck so far. But anyways its an early build so is there anything I need to look out for? I noticed today I pulled into a parking spot and went to back up and as soon as I put it in reverse the truck shook pretty bad. It did it a few times as I sat there and went from drive to reverse. Is this something that is normal?
View 9 Replies
My name is Linda & I own a 2008 F250 laritt crew cab , 6.4 I bought new in september 2007 .. I love my truck !!!!! but today i drained the water seperato as I always have it started and ran for a few seconds it sut itself off and now i cant get it to start
View 14 Replies
I have an '08 250SD diesel. The upper hose that goes onto the water pump has a leak. Is it usually just the Oring or the hose plastic fitting?
View 2 Replies
The doors on my 2005 crew cab are leaking water. Its happened once before, I fixed it by resetting the main seal around the doors. Now this tropical storm had them leaking again. The rear doors are leaking from the top and getting the head liner wet, and the front left door is leaking a little bit onto the middle pillar Guage and down onto my leg.
Is it time for new door seals? My 01 has never had this problem so im not entirely sure what to do.
View 3 Replies
Truck is a stock 2001 f250 7.3 with 205,000 miles. When accelerating or braking from about 40-60mph it starts to shake a little bit. When braking it shakes a lot more from 60 down to 40. But the faster you speed up the less it shakes when taking off. Looked at everything underneath is tight, and it has stock a stock steering stabilizer. Would a new stabilizer fix this you think?
View 7 Replies
I have a 1999 f250 v10 auto. It has 3 miss fires thats im stumped with .. Ive replaced all spark plugs, all coils , I've had injectors out and were cleaned and it still miss fires. I can disconnect the coil and injector on the cylinders and the motor runs the same. Ive swapped the coils and injectors around to make sure it wasn't them. What else could it be? Frustrated I've had the truck for 2 years and haven't figured them out. Ive had them go away for at most a day. Also the truck has a shake at 80 kmh not sure if its from the miss...
View 13 Replies
My 2004 F350 6.0L v8 has a weird shake when I get between 45 and 55 mph. Doesn't feel like its the tires, feel like the engine. I think I might have the #5 glo plug out. Is that it or could something else be wrong? If it is this how bad is it to drive on.
View 4 Replies
My 02 f250 started shaking violently until when I accelerated and the mechanic said it was the wiring harness in the computer. He said it was caused because of over revving I think it was just because the harness was old. Is it because of over revving? Will it happen again?
View 7 Replies
2008 f250 standard cab long bed 2wd base model 5.4. This thing has been great for the last few years i i owned it but it developed a shake since i got new tires. My mechanic mounted 4 new Hercules Terra trac at 2's on my 18 inch wheels (275 70 18) and when i got the truck back it was shaking violently at anything over 45. Mechanic says the new tires are heavy and its affecting other things...sounds plausible. So here i am a month later with a New steering stabilizer, all new ball joints, new shocks, new u joints, and 1 new tire (he said 1 of the brand new Hercules had a broken chord). The shake is 80% gone but this truck is still not the same. Anything after 65mph and it has a feint wobbly bouncy shake. I don't think its the dreaded hop that everyone gets on these. I have 2 theories:
1. These cheap tires just suck and will never be right
2. The cheap junk Monroe shocks he put on are way too soft to do anything
so what do i do? Should i get some crazy shocks or will that make this truck even bouncier? Im worried about making it even stiffer than it already is.
View 12 Replies
2015 6.7L Super Duty ... I bought this truck 74,000 miles and almost two years ago. About 6 months ago it developed a vibration and a very hard shaking of the steering wheel when (so far) turning to the left. First began when, from a dead stop at a red light, I turned left onto an uphill I-41 on-ramp. Scared the crap out of me and I had to pull over to a dead stop to get it to stop. Happened several times but only on this ramp. Local Ford dealer checked it out 2 oil changes ago and couldn't find anything wrong. Now, 2 weeks ago it did it on the highway at 65 mph on a slow, 80-ish degree and downhill turn on a 4 lane highway in Milwaukee. Again had to almost stop for the wildly shaking steering wheel to return to 'normal.' Am taking truck back to same dealer this Wednesday for it's next oil change and they will check it out again. I pull a 37 foot, 15K pound 5th wheeler and don't need to lose control at 70 mph!!!!!
View 6 Replies
I have a 2002 F250 with the 5.4 triton engine. Automatic transmission. When I reach 35 mph (sometimes sooner) the truck will shake horribly when I reach lower rpms. It will do this up to 65 mph and then it mostly stops. Completely taking my foot off the gas will stop the shaking, as well as shifting into neutral.
I know for sure that the truck has a cylinder 3 misfire as well as a minor exhaust leak, could either of these be causing it? Don't have the money to fix either of the problems for another couple weeks, is it safe to drive until then or should I play it safe?
View 2 Replies
I am not positive where it could be but I have a good bit of oil on the transmission (i think) i was trying to replace the strarter and noticed it. Where the possible leak could be from? No oil on the ground under the truck.
View 3 Replies
I have an 04 6.0 F250. I am having a shaking between 1500 and 2500 RPM around 45 - 55 MPH. I have no guesses what is calling this, but the truck runs fine otherwise.
View 8 Replies
My truck has an intermittent shake with a grinding/binding kind of noise. It seems to happen at lower speeds, generally when slowing down and turning. When I apply the brakes or speed up it seems to stop the noise.
The rubber/plastic seal on the back of the wheel hub is loose on both drivers and passenger side but I don't think that is the problem. I'm wondering if it is the u-joints or something.
The brakes look shiny and i don't see any scratches on them so I don't think there is a rock or something in there. I have the wheel hubs in the auto setting, and it is a 4x4. The truck is a early 99 7.3L with a leveling kit and 230k miles.
View 4 Replies
I have a '03 F350 that I can't seem to solve the brakes vibrating when applied. Replaced front rotors a couple weeks ago. I still have a vibration when I apply the brakes. What am I missing? I didn't replace the back rotors, but maybe I should have. On the passenger front, the inside pad was almost gone and the outside pad was in good shape. I greased the pins before I replaced the pads the last time, but the inside still wore much faster. I also blew out the rear brake line last week and spent Saturday bending a new line and replacing that so the brakes were bled when I had to replace that. I don't feel the pulsing in the pedal, but the truck shakes pretty good when I hit the brakes. What else should I be checking if the rotors are new and the pads are new and the pins have been lubed and the brakes have been bled?
View 6 Replies
Having a somewhat scary problem.....my truck is already a rough ride due to the fabtech lift and the 37's and you get a lot of feedback through the steering wheel. Its a rough ride down the highway but where it gets scary is at lower than highway speeds like 35-45 range. I can hit a bump and it will send the trucl into this insane cavitation that will literally shale the fillings out of your teeth. I cannot tell if it is in the drive wheels or the front wheels. The best way I can describe it is that its like trying to push a buggy in wal mart with a bad caster wheel on it. It feels like you are about to have a wheel fall off or that its broken off a tie rod or something. Then you simply slow down to a stop and you can drive right on like nothing was wrong. The vibration or shaking does not slow down with the speed. I cannot find anything obvious broken or damaged but this thing is getting dangerous to drive.
05 F350 DRW Fabtech 6 inch lift and 37's. 114k miles.
View 14 Replies
I have a 2008 F250 crew cab lariat 4x4 with 20 inch factory wheels that the steering wheel shakes during normal driving left to right. I bought this truck with 1500 miles on it. This shaking started at 50k miles and I was thinking it was a balance issue so I got new tires a month later since mine were about worn out anyways. They were factory replacement nitto terragrapplers. Shake was still there, swapped out for another set of nittos and shake still there, swapped to BFG AT KO's and shake better, but still there. I have gone through 10 or so balances, 5 roadforce balances, 2 alignments at 4 different shops including the ford dealer through the 3 sets. My wheels are scratched to hell and back from the careless people at the tire stores from so many balances.
My truck sat at the Ford dealer for a week just the other day and they changed the steering stabilizer. I thought it was gone, but a a few days later shaking started again. It almost feels as if every little bump, rut, crack in the road the steering wheel feels and shimmies (doesn't matter the speed, gets worse and more noticeable at higher speeds). The Ford Dealer says can't duplicate, but then when I go down there and test drive with them it's "oh yeah I see that, it shouldn't be doing that". The Ford Dealer says they can't find anything loose in the front end when I tell them to check tie rods, bearings, etc.
My truck has 62k miles on it now and it's driving me to the point of thinking about trading it on a Chevy. I love my truck, but it kills me everytime I make a payment and it rides like crap. I am still under extended warranty so I need to get this fixed before it goes out. I've also noticed that if I turn my steering wheel back and forth real quick while driving like warming up for a Nascar race I can feel a bumble in the steering wheel. This is NOT the death wobble as I use to get that around the 20k mile range and it disappeared and has never been back.
View 14 Replies
Picked up a project truck for the spring..... single cab 99 4x4 7.3 with the 6 speed. 1st through 5th work perfect...... however reverse and low are non existent.
What I am sure of:
1. I'm positive its not a clutch problem.
2. The shifter goes into the position of reverse and low just fine but there's no engagement at all.
3. I can put the shifter in low or reverse position whether the clutch is engaged or not... makes no difference at all.
Once i was messing with it and somehow by moving the stick sort of to the side it hit reverse and the gear worked fine but then it remained in reverse no matter what position the shifter was in until i was able to move it around enough to get it out.
I'm thinking bent shift fork? Looking at a few writeups on rebuilds it looks like i might be able to replace the fork without dropping the tranny.... just divorce the t-case and remove back half of trans?
View 6 Replies
