So I shorted wires out putting a new plug on my mirror, and now I have no turn signals, no backup lights and no overhead display that shows mpg and outside temp. All fuses are good, and I don't think it is my flasher relay just because I also have no park lamps or over head display.
View 3 RepliesMy overhead display quit working earlier this week. The truck has 120k miles. Is this display on it's own fuse? I only used it for the outside temperature readout but I would really like to get it working again.
View 3 RepliesThe #8 fuse under the hood was blowing on my '00 F-250 every time I turned on the healights meaning I would lose power to my park lights. The brown wire coming from the back of the headlight switch showed a dead short to ground that I traced to somewhere between the switch and the firewall.
Anyway, I got tired of trying to pinpoint the ground fault, so I cut the brown wires at the back of the switch and under the hood at the top bolt-on electrical plug and replaced the bad section with a new wire. It works fine now with the only exception being I do not get the park light flash when I hit the remote lock button the second time. I do still get the horn chirp.
My Haynes manual indicates there should be a relay box with a Park Lamp relay, Driver Unlock relay, All Lock Relay, and All Unlock relay. The park light relay looks like it sends the blip of power to the park light circuit. Where this relay box is? I'd like to splice into the brown wir coming out of it to restore the light flash when I lock the truck since sometimes it's too noisy to hear the horn.
I just got a 2000 F350 cc drw 7.3l.
I did search but have had no luck. My turn signals do not work, unless my foot is on the brake pedal my green arrow indicator wont even turn on. When they do my bulbs work but don't cycle so I know all the bulbs are good as I had my wife check all four corners when I got them to come on for a split second. I have tried replacing the MFS and the turn signal relay under the radio in the dash.... When I do turn on my blinkers I can hear the relay click once but that is it, no more.
I tried checking the wiring in the column and tilting the column to its extremes while trying to engage the turn signals. Also, if I unplug the brake light switch then I do not get an arrow on the IC to light up so I am guessing the power flows through that switch. I don't have a chilton manual yet and the owners manual was not in the truck. I did check fuse 23 ?
Coming back from a trip I got a e-brake light show up on the dash then noticed the signals stopped working and the heated seats no longer turn on. I scanned it with my AE and got a brake fluid sensor error come up but nothing about the signals .... is this a common problem or is there a connection between all this? 2003 F350 6.0L .....
View 2 RepliesEvery time I put the truck in reverse, I get a "Check Rear Park Aid" message on my display.
I tried wiping all of the sensors clean, and I checked the electrical connections and all seem to be fine.
I have a f 550 that blew out starter cyl on inner fender.and starter, replaced both. Now I have no brake lights or 4 ways and no turn signals....
View 4 Replies1999 F250 super duty. I am having a problem with the front right turn signal not working. The indicator on the dash also does not work but I can hear the relay clicking double time and the rear signal works. I have changed the bulb and fuses and went under the dash and the column to be sure a connection had not come loose. I have looked through the forums to try and find an answer with no luck. What to try next?
View 4 RepliesI own a 1999 F350 CC SRW w/ 7.3L PSD engine. My turn signals stopped working suddenly. I've checked the fuse panel under the dash but it doesn't show any fuse for the turn signals.
My hazards do work although I noticed something very strange. When I tilt the steering column down the hazards stop working and when I tilt the column all the way up they work again. Still no turn signals though.
I have a 2002 F250, 5.4 extended cab 4x4. Factory lights. I have no turn signals. They were working just fine and without turning off the truck, all 4 corners quit working at the same time, as far as I know. The indicator lights on the instrument cluster don't work. I have checked/replaced all fuses. Replaced the switch lever and the blinker relay behind the dash. The hazards do work and always have. It might be coincidence but I believe the back-up lights quit working at the same time.
View 2 Repliesonly have clearance lights at plug no output for brake and turn signals
View 1 RepliesI'm having problems with my front marker lights. The turn signals work but when I turn on the parking lights or headlights they don't work. They only work with the turn signals. And I can't get the front side marker lights to come on. I've tried everything...
View 2 RepliesI have a 2004 350. Turn signals quit working don't come up on dash either but when I turn the flashers on the left turn signal on come on that's on the dash and the lights. I replaced the turn signal relay that's under the radio. The old one would buzz when I turned the turn signal on but nothing would come up the new one clicks as it should but I'm still not getting turn signals lights on dash nor the light it's self. The flasher is still like it was only the left one comes on.
View 1 Replies2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
2005 F350 Super Duty. I have no brake lights turn signals or hazards. dealer suggested the multiswitch but changed it and still not working?
View 2 RepliesI have a 2006 F350, it keeps blowing fuses for the brake/turn signals. The puzzling​ part is it only does this when the truck is running.
View 2 RepliesMy sons 2006 F350 brake lights and rear turn signals quit working. When the headlights are on, all the lights operate but the rear turn signals and brake lights do not nor do the emergency flashers. The front signals work but flash very rapidly. Although I'm not an auto electrician, I'm fairly mechanically inclined but the fact that the front signals work, the rear don't and all lights work as lights, just not as turn signals or brake lights.
View 4 RepliesI have a 2006 F250 Superduty 4x4 that the brake lights hazards and turn signals have stopped working in the rear.. The middle cab brake light does not work either.. The running lights do work as well as the turn signal and all lights in the front.. I also checked the trailer plugs and both work for running brake and signal lights.. I have checked all fuses under the hood as well under the dash with a test light and i have nothing blown.. I have replaced the Brake switch as well as the flasher module under the dash and picked up a new multifunction switch (Turn signal/hazard) and that didn't work either.. I'm stumped at this point.. I have not checked the bulbs yet but wouldn't think they would all blow at the same time.. (will do this next)..
View 3 RepliesEvery time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
I was adding some more running lights today and tried to tie in to the front running/turn signal light. Next thing I know I hear a pop and now no turn signals, hazards or brake lights on my 99 F250 SD V10. My 3rd (center) brake light does work though when I press the brake, it's just the tail brake lights that dont work.
I can't find a blown fuse for the turn signals or brake lights (not really sure which fuse box it's in since the manual doesn't tell me what fuse is what)
I however did find what I'm guessing are the flashers behind the radio. What might have went wrong where before I start dumping money in to flashers and relays.
The next question is, can I jump in to the marker/turn signals and add another single LED light to them off the front? If I can which color wire does what?
I have a 1995 Ford f250 Powerstroke and i do not have turn signals, rear running lights, brake lights or reverse lights. i checked the fuses and they seem to be good but i dont want to tear everything out to check the harness if it could be a bad ground. any insight?
View 1 Replies