Ford Super Duty (1999-2016) :: Missing Some Brakes - Pedal Is Extremely Spongy
Mar 22, 2015
I'm not exactly sure what's going on but it feels like I'm missing some brakes - the pedal is extremely spongy, I have to push it nearly to the floor. And when they do engage, it isn't with the same vigor as they did before.
It's strange, it just sort of happened - I drove to a friend's house, everything was fine. But when I left all of a sudden, there's this problem.
It's not like the pads have come apart and destroyed a caliper - I had that happen to me a few years ago and I definitely felt it happen, plus once it did I lost almost all braking ability as the lines would just leak fluid.
View 2 Replies
Advertisement
I replaced all the brake pads on all 4 wheels. Pretty standard procedure. I now have a very spongy brake pedal. It stops but the pedal will be almost to the floor. I did not break any of the lines open during the procedure just used c-clamp to spread the calipers. No ABS light. Have a Snap-On power bleeder and bled the system several times with no change. Checked the power steering fluid level and inspected entire system for leaks.
2002 F-550 V10
View 8 Replies
I have a 2002 f350 Super duty, 7.3. After I changed out the power steering box, I did bleed the system, I have now power steering and the brakes are very spongy. Any thing to check prior to replacing the booster? I have been told the power steering is probably just an alignment issue and I should bleed the brakes.
View 3 Replies
I noticed last week that my brake pedal seemed more spongy than usual. The next day the pedal would go down about half way to the floor before I had pressure. And then the next day the pedal would go straight to the floor. Pedal comes back up once released. I still have brakes pressure about an inch before the pedal bottoms out. Its been like this a couple days now. The vaccum pump works fine. I'm gunna try bleeding the brakes on it tomorrow.
View 5 Replies
I have a 2001 F-350 Diesel 4x4 crew cab 8ft bed dually 7.3 diesel 6 speed. The issue is that the parking brake pedal is extremely hard to push. One day it pushed down and ratcheted into a locked position as normal and the next day I couldn't push it more than an inch down. I have rear disc brakes with internal drums in the rotors for the parking brake assembly. I replaced the shoes and hardware (which were fine) and I still have the same issue. I removed the front single cable from where it splits into the two rear ones and the foot pedal depresses smoothly and with the touch of a finger with no load on it. What else is it? The only other thing is one of the rear cables unless I am missing something?
View 5 Replies
Ive got a 2002 f250 Sd 4x4 with 93000. Im getting severe vibration from the front drivers side at highway speed. I thought it might be a warped rotor but i cant feel it in the brake pedal, when I put the brakes on. How can you tell when the hub bearing assembly is going bad? The truck doesnt pull to that side either. I can hear it, and feel it more when i'm going around highway corners. When im driving through town, I can hear a "clunk,clunk,clunk" noise coming from that side also.
View 14 Replies
I took delivery last week of a new 2012 F250 with a 6.7 Power Stroke Diesel. This is my third F250 with a Power Stroke Diesel. My first one was a 1997 w/7.3 PSD and my last one was 2001 w/7.3 PSD which I traded in for the 2012.
Now for my problem. The brakes seem spongy to me. When I am applying the brakes I get what seems like a longer than normal pedal travel (to me anyway) and soft. The braking isn't as good as my last two F250's. If I pump the brakes, the brake pedal firms up and the braking really improves. I have not contacted my dealer yet.
View 14 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
My 2014 F-350 SRW always seemed to have spongy feeling brakes since day one and the e-brake has never been set-up to be very tight. Even though my truck has less than 25,000 miles on it, I'm half tempted to power bleed brakes to try to get a better brake pedal. All I know is that if I press the brake pedal on my '82 F-350 SRW as hard as I need to press the one my 2014 SD, it would try to put me through the windshield.
View 12 Replies
1999 F-350 . My shifter lever is extremely loose, it will not go into park at all. I tightened the two torx bolts, adjusted the needle but its still bad. Im thinking the cable is loose, I saw that there is a small rod attached to the end. Is there a way to tighten it or do I need a new cable assy.?
View 5 Replies
My steering got real "heavy" almost as if I had no power steering so I replaced the power steering pump. The steering got a little easier but is still very stiff. It's extremely hard to turn at low speed just off idle...I have to rev the engine a bit to get it to turn.This is on my 1999 7.3 f350...I've ran 33" and 35" tires on it it's whole life and this is the first PS pump I've replaced since 1999...never replaced the steering box.
View 9 Replies
I'm completely aware a lifted truck will not ride factory and most likely ride harder. But this is ridiculous.
So I bought a 8" super lift for my F250 7.3 2000, although the price is very cheap at that shipped to my door debating if I have messed up either with the brand or somewhere because I feel like I went from a casual ride in my lovely 7.3 to feeling like a horse carriage of a few century's ago.
Lift is setup with lift leaf springs in the front, one add a leaf in the rear with a block, and 4 new shocks and all the other hardware included to do the lift.
I'm wondering if it's possible the springs are installed wrong, or the shocks are just that bad or if there a weird issue I've over looked.
Tire pressure is set to 35-40 psi all around on toyo open country mts, (which I was running before the lift so that hasn't changed) but I mean this is so stiff that when I hit a bump my steering wheel jerks and I feel like my suspension has absolutely no flex in it. Debating on returning to stock or not at this point...
View 13 Replies
Have a 2000 F-250 V-10 4x4 with 335,000 miles on the clock. Has started hesitating at 40-45. You can't really notice it at idle. Drove it around at lower speeds and just a miss here and there. Take it up to 40-45 and it's quite bad. Hasn't thrown any codes. Hooked it up to the scanner to get no additional info. My gut says coil packs but am kinda confused that I haven't gotten a misfire code yet. What to check?
View 6 Replies
My 99 f450 7.3 runs bad on first start of day. I checked the codes 3 codes p0475, p0470 and p1247. Now here is what I tried I plugged it in over night and it will start and run as should the next morning with out side temp 47. Drove the truck late yesterday evening didn't plug up tried it this morning with a outside temp of 47 truck starts but missing and like of power. My problem seems to be temp related. Will low boost pressure cause this problem what do I need to do?
View 4 Replies
Ok AC wasn't working took it to a mechanic told me the the compressor was missing a clutch he recommended i put a new compressor. Is it possible just to put a new clutch in it and if so do i have to remove the compressor to put the clutch on it.
View 14 Replies
One day after my mechanic replaced the heater core my truck started to misfire after the motor warms up and is under load. No codes and nothing pops up when hooked up to o a scanner. It's been cold in the morning and when I start it up it runs like a top. But after it warms up it start to miss a little, then it gradually gets worse especially when under a load at higher speeds. I thought it was a vacuum hose or something got left unplugged.
View 7 Replies
I went to replace my driver's hub bearing last night. Found pieces missing from the locking hub (manual). I ordered them last night it's the snap ring and washers but will not be here till next Monday. Can I run the new bearing with out hurting it. It has already ruined the seals on that side I just don't have the time to take it all the way down. So if I install the bearing and don't put all the guts in the locking hub (I know the locking hub won't work) Dont need 4x4 right now but need to be able to drive it some. Just don't want to mess up the 250 dollar bearing I just got.
View 2 Replies
2003 6.0 is acting crazy again. Has new ICP, IPR, oil discharge tube, and hpop. It cranks right up but one time you crank it and all the gauges work correctly, especially the fuel gauge. The engine will idle perfect but when you accelerate it has a dead miss. May crank like that 2 to 4 times. Then you crank it and it runs like crap, and the gauges won't work, the fuel gauge goes past E and the light comes on. As long as that happens it runs terrible, but when the gauges are working it idles great but has a miss under acceleration! It was running fine, then just went nuts!
View 4 Replies
I use a bottle hanging like an I.V. drip to flush the Brake Fluid in all my cars. I can pump all the old fluid out, as well as the air. My Superduty 7.3 has a good solid brake pedal after the flush. It seems to me the rear brakes handle 60% of the stopping load. Its been like this for so long I'm not sure if it's ever been different. i then go to a gravel or wet road and test the rear abs, and it seems o work, but definitely has a squirrely feel. I did some strong pavement stops with speed, and it stops, no skidding. Is that the way it should be?
View 14 Replies
Just bought a nice little project 1999 4X4. 100k miles and overall decent condition.
One of the first things to tackle is the driver's front hub has no manual 4x4 locking mechanism like on the passenger side. Is this a tough job?
Attached is the picture of the hub & missing lock setup. (Can't upload...).
View 8 Replies
I have a 03 F250SD with ~145,000 miles on the 5.4L. Just recently I have been having what seems to be a miss, or possibly a dead cylinder. I thought it might be a dirty MAF, but I cleaned it and have the same problem. The miss is more noticeable at the higher RPMs. I am checking the plugs today. So any solution? I refuse to take her to the shop and having another man up in her manifold.
View 8 Replies
