Ford Super Duty (1999-2016) :: Loud Squealing Sound On Driver Side / Lift Pump?
Oct 16, 2016
Truck details:
2008 f350 6.4 290,000 klm
DPF and full EGR delete
K&N intake
IDP custom street tune
Loud squealing noise that happens when cold or at temp.
2000 to 2500 rpm's to 3000 rpm then it goes away
Happens only when accelerating over 50% anything under and the noise doesn't happen.
15 to 20 pounds of boost
Turbo sounds good
No codes
All plumbing looks sealed and tight
Fuel coolant res is full and clean
I'm thinking it could be the lift pump dying or having trouble supplying the fuel demand. Started after I did the cold air intake....
View 8 Replies
Advertisement
I bought a 2004 F250 super duty 4x4 with the 6.0 a couple weeks ago and have a few questions. Hopefully all of these things are normal, but I thought I would ask you experienced drivers.
1) Occasionally while driving when I lift off the accelerator pedal I can hear a sort of loud rattle under the hood. I assume this is the turbo shutting down? Is that normal?
2) 4x4 and locking hubs... I have the 4x4 hi and low switch on the dash. Do I need to also manually lock the hubs to go into 4x4? After reading the manual it seems like I can just turn the dash switch and they should automatically lock, but I'm not sure. The hubs are not marked, but going by the pictures in the manual I think I know which is "lock" and which position is "auto" or off.
3) Front wheels hop at full turn. I expected wheel hop in 4x4 or with the hubs locked, but even in 2WD with the hubs in the auto position the tires still "hop" or knock a bit at sharp turns. Is this normal?
View 2 Replies
I have a 99 f250 4x4 super duty. Just started getting a loud squealing noise off and on in the front end. Changed the ujoints and axle seals on both sides. They where all in bad shape. It still makes the noise off and on while in 2wd. If I lock the hubs in it doesn't. What it could be ?
View 14 Replies
The pads were replaced 5000 miles ago. Today the truck is acting hard to go, brakes are squealing, and I noticed a hot brake smell. I got home, grabbed a remote thermometer gun and the front rotors are 130 degrees, the back ones are 650 and 700 degrees! Super hot. I'm going to NAPA for new calipers and pads. I hope that fixes it.
View 3 Replies
I have a 2013 f250 6.2, I bought the truck brand new only have about 3000 miles on it and the other day I noticed that the drivers side front is lower then the passengers side front, the drivers side is about one inch lower, this doesn't seem right, also my drivers side front wheel seems to be pushed forward about one inch to the bumper that also doesn't seem right.
View 3 Replies
I have a 2004 Ford f250 6.0. When driving it down the road i will hear a loud spinning sound, sorta like putting a playing card in your bicycle spokes. The sound can be heard until I make a complete stop where at that time the sound stops and a clunk can be felt. After that the truck sounds normal. This also only happens once between starting the truck and turning it off. I took it into the shop and they could not hear the sound, all they said is i need new ball joints.
View 6 Replies
So last week I installed a 6" lift and once we got it done I could barley turn right at all. So I decided to put a drop pitman arm on yesterday with a buddy, thinking that was the issue. But I still have the problem, and I very badly need to fix it and don't know what it is. Turning left is completely fine however. It feels like I'm trying to steer an 18 wheeler right now.
View 6 Replies
Looking to upgrade my tires and would like to go a hair bigger but nothing radical. I have the 20's now, what's the biggest size I can go to with no lift.
View 2 Replies
On the F250 trucks, if I changed the mounting frame under the seat, will the passenger side seat fit on the drivers side? Basically, can I turn a passenger seat into a drivers seat?
View 4 Replies
I have a fabtech 4 link 6" lift on a 2008 6.4. The lift kit used to sit level but the front is sitting lower now. How can I fix this?
View 10 Replies
My 2002 F250 with the 5.4 (215,000 miles) has a loud tap upon start up, only on the passenger side, heard best in the wheel well. It only lasts about 30 seconds to a minute. It occasionally rears it's head driving around town but only intermittently. Just drove it 275 miles, at 13mpg, truck runs fine, just annoying.
View 9 Replies
Picked up a new to me 2011 F250 Lariat. She had a few odds and ends to take care of, but I was ok with that. So far I fixed the reverse sensors (2 were out) creaking in the back (leaf spring bushings needed a little Lithium Grease) Squeak in the back (tailgate step needed a little greasing). Now on to my next problem!
This is my first 6.2l (first f250 in general). Truck starts up great and idles quite. Taking off driving, it sounds loud as hell under the hood. To me it sounds like the Fan is making a loud sound as the motor is accelerating. It is more noticeable when you really floor it. Prior to this I owned a 2010 F150 and I know stomping on it the motor really revs up, but this other sound to me isn't right/normal. Googling around, the closest I found to it was:
Loud "Air" Sound Upon Accelerating 2002 FORD EXPEDITION - fan clutch! - YouTube
Granted it's for an expedition, but the sound is damn near identical. Looking on youtube at 1 or 2 videos of a f250 doing a 0-60 all I heard was the sound of the motor revving, so that has me convinced the sound I'm hearing is not normal. I'm 99% convinced it has to be the fan clutch.
View 8 Replies
The Truck: 2011, 250, 4x4, Super Cab, 6' box, 6.2 with 6R140, currently 40K miles. It did have an 8' plow on it. An 80 year old gent plowed his personal 200' driveway with it for 2 winters before I bought it. You can tell the truck was taken care of, or I wouldn't have purchased it. I have all the service records. He had his local dealer do all of it. Plow and all the controls were removed prior to my purchase.
Scenario: Trucks cold (summer ambient). Driveway has a grade down to road. Doesn't matter if I am nosed or backed in. Start up, back/pull out of driveway on to flat road, and very slowly take off. The 1-2 shift produces a lose thunk sound and sensation, very faint not loud. Almost Like a lose motor mount. Only will do it once, only on the first start and 1-2 upshift. Ive tried to reproduce it after the first occurrence, no luck. If you gas it under the same circumstances it wont do it.
It doesn't necessarily feel like an internal trans problem. More of a "somethings just lose enough to shift or move" problem. Sounds like somethings hitting the frame, core support, cab floor on this slow 1-2 up-shift. Its upfront passenger side. I've spent several hours under it looking for lose items witness rub marks etc...to no avail
Again it only does it after it sits or upon the first start in the AM or when leaving work PM. Not when its warm.
View 14 Replies
I have a 2003 Ford F450 super duty xl. At first there was a loud clicking sound coming from under my dash. I charged the battery up and the sound went away but the truck will fire up but not turn over and start. I thought maybe it could be the relays but the clicking sound quit.
View 2 Replies
So I'm getting a mild to severe shudder depending on load and acceleration rate from stop to 10-15mph... It's worse if I'm on an incline...This has started since having a lift installed...I'm guessing it has everything to do with pinion angle...right?
1999' F350 7.3L 4x4
Crew Cab Long Bed
View 2 Replies
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
View 12 Replies
I have a 02 f250 powerstroke and I wanna put a suspension lift kit on it I wanna go with a 6 inch lift but I'm afraid if I go any higher than a 4 inch I'll have to change to much. What I would have to change and if I would have to extend any of my brake lines also the truck is a cab and a half with an 8 foot bed so I do have a carrier baring on the drive shaft would I have to change anything with that?
View 14 Replies
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 Replies
Put in 2.5" leveling blocks under front coil springs. Now I hear a clunk nearly every time I turn to the right. Why this might be?
View 3 Replies
I got to replace mine because the hood won't stay up on it's own and is heavy to lift. I was wondering if these things fail often. Mine is an '08.
View 5 Replies
Just installed a 4" lift sunday, with a BDS drop pitman arm and then i retorqued it to 185 ft/lb. I now have this extremely low speed (<2mph) or stopped clunking whenever i turn the wheel. I just replaced the upper and lower tie rod that goes from the pitman arm, and its still doing the same thing. Steering box is shot?
Clunk after lift install - YouTube .....
View 5 Replies
