Ford Super Duty (1999-2016) :: Jet Sound When Pressed The Pedal And Got Louder As Speed Increased
Apr 28, 2016
I have a 2004 Ford f-250 super duty 6.0 turbo diesel. I noticed yesterday that it was making a jet sound when i pressed the pedal and got louder as i increased the speed. When you let go of the pedal it goes away. I have asked around and some say it could be the turbo...the diesel mechanic THINKS it could be the fan clutch. The truck doesn't overheat and if i punch it i don't think i sense any loss of performance. All I know is that it makes this sound like a plane taking off.
View 14 Replies
Advertisement
Had a No start issue.Turn the key and nothing. Could hear the relays click so knew it wasn't the ignition. Could jump the starter via the wire on the passenger fender so starter good. Replaced the clutch position switch last night. Still have no start but now when I press clutch I have a tow haul light come on dash.If I press it again it turns off. Truck doesn't have tow haul option installed. I hear a relay clicking under the dash too. This is a 2004 Superduty (F550). Replaced the ignition switch today and still same.
View 3 Replies
I'm having issue with my brake lights. Checked for voltage and nothing. Checked the fuses under the dash. Checked the brake pedal switch and have power going out when the pedal is pressed. Is there a relay or something somewhere else? 1999 f250 7.3 superduty....
View 2 Replies
Recently my F350 has failed to downshift when the accelerator pedal is pressed to the floor to speed up in traffic. It will usually happen when traveling at speeds in the 30's-40's. It will shift quickly at slower speeds. I have a scan guage on it all the time and it is not throwing any codes.
The transmission has only been serviced by the dealer; last done about 24000 miles ago. No leaks or low fluids/no burned smells. Stock setup with no heavy towing use. Currently at 228000+ miles, this is the first issue with the transmission assuming I am looking at the right area for the cause.
2005 F350 XLT 4WD
View 8 Replies
My radiator has been leaking very little for some time and it is stock after 250k so im sure it is plugged....my engine has been running 202 .... My tranny only goes over 200 while towing...otherwise if is under 190
View 14 Replies
I have a '16 F250 4wd with the 6.7 and approx 3k miles. There has been a strange sound coming from the front end when turning left from a stoplight. It sounds like something slides or shifts and it only happens once in a while. The noise isn't loud but you can feel it.
View 2 Replies
[URL] ....
The problem with my truck is not that its regen'ing too often, the problem is that its STUCK in regen cycle. For the past 4-5 days my truck has been going into regen about 1-2 min after i start driving it, every single time i start her up. If i start my truck in the morning and let it warm up for a few min, i come out and my truck is idling higher then normal and has an increased exhaust smell, but when i aply the brake the idle goes back to normal. Then i start driving up the street and BAM "cleaning exhaust filter" message comes up and the and immediately the sound of the exhaust and induction changes and it sounds like sputtering/knocking.
Sometimes the the engine will flutter in decel or shutdown. HORRIBLE gas mileage, Reduced engine response and power, and white smoke is cooler temps. Basically all of the normal signs of a regen cycle, am i wrong? Im pretty sure its either a dpf sensor or possibly something wrong with the DPF? I haven't had one problem with my 2010 besides an egr valve and she has 167k miles and is completely stock and im very happy with my truck! 2010 6.4L
View 2 Replies
Ok so my fire station has a 2003 f550 rescue truck with a rescue body with the round tail lights, we recently upgraded them to the LED ones that are much brighter but of course it flashes at the speed of sound. The question I have is:
1. the relay {flasher} is located on the driver side inner fender? I think....
2. does the same EP-27 relay/flasher fix the problem?
View 1 Replies
I bought my 2012 F250 CC SB 6.2 back in December and really haven't had the truck in 4x4. Today we got a bit of snow. The roads were slippery so I engaged the 4x4 ESOF while at a stop sign (I know, didn't have to be stopped but I was so I put it in 4x4) The driveline was noticeably louder.
I had a relatively constant hum that almost reminded me of a wheel bearing going bad. If you've ever experienced a wheel bearing going bad the sound gets louder as you go faster. I'm sure it's not a wheel bearing since it only makes the sound in 4x4.
It's a fairly annoying sound and is louder than my old 99 F350. Notice the driveline being significantly louder in 4x4? There are no driving issues just a louder sound than what I was used to. I have the full Ford Certified warranty and can bring it in but I thought I'd run it by the brain trust here to get thoughts before going to the dealer.
View 10 Replies
The front brakes on my '02 Super Duty squeal a little from time to time, but today have been squealing mildly while driving and get louder the further down I press the brake pedal until coming to a stop. All new brakes were installed less than one year ago.
View 11 Replies
Ok, did an intake manifold cleaning on my 99 Accord the other day, and now I have problems...
Long story short, some time ago my car started to have a very rough idle. Took me awhile to find the problem. Turned out the air hose, between the filter and throttle body, had developed a big hole on the underside. So I replaced it and while I was at it used some throttle body cleaner, spraying into the intake manifold chamber. Lot of junk blew out the tailpipe. The car ran much better, but the idle could still be a little rough. I ran it that way for awhile, and finally the other day decided there was probably still some junk in there and it was time to really clean it out. So I took ff the throttle body and intake manifold housing. There was a lot of junk in there! The small intake on the passenger side was completely clogged shut. (I understand this isn't surprising on these cars.) I used a bunch of rags and 2 cans of Valvoline throttle body cleaner and a lot of elbow grease and cleaned it out. I was thinking to myself that whatever I didn't get with the rags flushed through OK, but I didn't want to take the whole intake manifold out.
So I put it all back together. (I took a video before I started, so I'm pretty sure it's all back together right.) But now I have problems. The car starts. It idles fine mostly, but can be a bit rough. But the trouble starts when I put the pedal down. If I do it in Park, well, if I push it quick the engine just dies. If I push it slow, the engine revs then quits, revs and quits, over and over. Similar if it's in gear. If I push it hard, the engine stalls. If I push it gentle, it revs up, but chugs along a bit.
I've run some seafoam through it, thinking it was clogged up with all that junk, and sure enough, lots of smoke comes out, but nothing is improving so far. What have I done wrong?
View 19 Replies
My issue, just purchased f250, 2004, v 10, manual transmission, state vehicle with 32,000 miles but was a plow vehicle for localRMV lot, that said, great shape and runs strong but I get a clunk and shutter when I am in reverse and only when I push down clutch before stopping. Doesn't do it starting forward or reverse, only reverse and when I push clutch in before stopping. Did have a friend drive and looks like the transfer case is moving, as if mounts or bolts are loose. Does this make sense and could bad slip joints be putting excess torque on ?!?!?
View 4 Replies
I am a recent new owner of an 06 f350 Powerstroke. Steering Box developed a leak so I decided to replace the box and go ahead and do the pump and hoses while at it. Pump would make some noise so i figured I'd just do it all and be done with it or so I thought. The job was a pain, much harder than the pump and boxes i've done on the older 7.3 powerstroke.
Anyways, used all OEM components (pump was a rebuilt rotorcraft, can't buy new anymore) and everything seemed great for about a day. I tried to bleed the air out per standard practice of turning the wheels with the truck off the ground. At startup and during the first day it had almost no noise at all and the steering felt much easier than the old pump.
Then the pump started to develop the standard annoying ford power steering whine that I hear all the time. Drove it over the weekend on a 160 mile trip and the noise just kept getting worse. As of tonight I can't turn the wheel if the truck is stopped even with my foot off the brakes.
I used synthetic ATF for fluid and there is absolutely no foam or aeration in the reservoir. Good news is I don't have any leaks but the bad is I now don't have power steering. It does make a much louder whine or squeak when I hit a large bump turning, I guess that's just the sound of the pump being stressed more. I am guessing the pump just crapped out but before I do it all over again.
View 2 Replies
On a cold crank the engine idles rough until it warms or the accelerator is pressed down. Also runs rough going up hills or towing. Check engine light is on and is throwing the code for bank 1 to lean and cat performance below threshold. Cats have been tested, good. Fuel trim tested, good. One mechanic said noth8ng is wrong with it well, there is. 2011 f250 6.2 gas...
View 5 Replies
Seems like my truck won't move at 4x4 when getting into and out of parkings. Combination of low speed and turning feels like I am fighting the truck and need to apply more power to get it moving and then there are strange noises.
Is this normal behavior from 4x4 system? I think it is but just want to make sure that constant switching between 4x4 and 2x4 is normal. I was just to AWD cars before that.
View 6 Replies
1999 F-250 4x4 PSD, 160k miles. Sometimes, at low speed like 5mph or less, when braking the brakes are almost gone and one can feel the stiff pedal coming back up when stepping on it hard to make the truck stop. The ABS is set to not kick in at this low speed, right? Truck throws no code and shows no warning lights (ABS light in dash works with key on-engine off) when this happens. Pull the related ABS fuse and problem goes away. Where to look?
View 11 Replies
I have a 06 f360 PSD 6 speed. On a road trip and the clutch pedal is getting very close to the floor. No Slippage but the longer I leave the pedal pressed the worse it gets. Are there any good descriptions how the clutch in this truck works?? Slave cyl??
View 14 Replies
I replaced all the brake pads on all 4 wheels. Pretty standard procedure. I now have a very spongy brake pedal. It stops but the pedal will be almost to the floor. I did not break any of the lines open during the procedure just used c-clamp to spread the calipers. No ABS light. Have a Snap-On power bleeder and bled the system several times with no change. Checked the power steering fluid level and inspected entire system for leaks.
2002 F-550 V10
View 8 Replies
Just got a 99 super duty and I have a very weird problem. When stopping i feel a very strong pulsing from the brake pedal. I assumed warped rotor. but the strange part is when I hit the brake the cab dome light comes on. How to locate this pulsating?
View 8 Replies
A bit annoying. 2008 F-350. When the truck is cold there is a creaking feeling I can feel through my foot. It usually lingers while the truck is warm but eventually goes away. It's in the actual pedal. This may be a stupid question but is there anything that can be lubed under there ?
View 10 Replies
Test drove an 08 V10 today. Brakes seemed to work fine and didn't lock up but I felt no pulsating in the pedal and heard no chirping of the tires like most ABS systems do. Is this normal? Anything special to look for in used late model V10s?
View 1 Replies
