Ford Super Duty (1999-2016) :: Intermittent Miss - P0352 Code For Primary / Secondary Circuit
May 9, 2015
Have an intermittent miss I can feel when driving 2006 F250 5.4 l 4x4 stick; Freeze frame from Cen-Tech 60794 (from Harbor Freight) scanner follows.
DTC CNT 0
DTC FRZF P 0352
FUEL SYS1 OL - FAULT?
FUEL SYS2 --
LOAD PCT 25.9
ELT (DEGREES F) 186
SHRTFT 1 0.0
[Code] ....
I can operate the scanner but what these ranges should be. What might be causing the miss? This scan shows 951 rpm, I was idling along in 1st in traffic, but I have also felt the miss at 75-80 mph (about 2300 rpm) on the Interstate and at other times, with light loads in the 1500- 2000 range in town.
View 2 Replies
Advertisement
The 2005 Avalon has 48K miles and it's been running well without any issues, until today.
Driving in city traffic, max speed is about 30 ml/h, The "Check Engine" light and the "VSC (Vehicle Slip Control) Off" lights came on. I did stop the engine, restarted after couple of minutes and the same lights stayed on. The car ran just fine, no noticeable difference in performance.
With the OBDCOM reader, the Avalon has this code:
P0351 232
P0351 Ignition coil A primary/secondary circuit malfunction
That seems to indicate a malfunction for cylinder A, or #1, ignition coil that has nothing to do with the "VSC" AFAIK. Is this a misread by OBDCOM reader, or the Avalon is confused?
The code had been reset via the OBDCOM reader, the car runs fine, neither of the lights come on now. Should I do something about coil A, or just wait until the code comes back?
View 1 Replies
I know this is a common code and a common problem. I have had a buzz test and glow plug test done, no codes. Scanner code came up with P0275. I have read about injector change out, to O ring failure, to new EGR style. I have a 05, 6.0 SD SRW auto.
View 1 Replies
I have a E350 5.4 with 200,000 miles and it ran great before winter, this spring I fire it up and it got a miss I drive it anyway it starts to clear up and now the 1289 code. Everything looks fine coolant engine temp. I wonder if you can bypass the Cylinder Head Temp sensor. I am thinking the engine management is causing the miss to cool the engine.
View 3 Replies
I just purchased a 2003 F250 Super Duty with the 6.8L V10 It has really high miles on it as it was a landscaping companies fleet truck. I'm sure that it was pretty well serviced as it has 300K miles on it and it's still running pretty decent.
I picked up the truck and I have to get the smog done soon. It idles with what I can only describe as a slight miss and it runs and drives great. seems to have plenty of power for the miles that's on it.
There is no active CEL on but I scanned the OBDII system and found a P0171 Lean bank 1 code in the pending codes list of the scanner. I guess this year engine doesn't have an EGR Valve or DPFE sensor because I've looked high and low for it and there non existent on this engine.
I've checked for vacuum leaks by spraying brake cleaner or carb cleaner all over the place and it makes no difference and all the vacuum lines and connections look okay.
When it's running It does sound like a vacuum leak right behind the top of the plastic throttle body but I can't find it, I don't know if this big *** engine just sucks that much air or what.
Like I said I need to smog this thing soon and I don't want it to fail if it's missing or has another issue. The fuel injectors look new and one coil pack looks like it's a replacement...
View 14 Replies
I have a f350 2000 4x4 automatic 170.000 miles. Service light on and OD light flashing. I have code p1747 "EPC solenoid short circuit"
This code make that the engine runs slow without power and hard shifting. I change all the solenoid body and check all wiring.
Later using a voltmeter i separate EPC solenoid wiring and see that have 5 volt. If I don't accelerate more 2000rpm OD light is not flashing and truck works normal but slow.
When I accelerate more than 2000rpm OD light begin to flash and transmission fail more. I check that EPC wires mark about 0 volts when OD light is flashing. Transmission hydraulic system seems to be ok because oil is very red and clean. Maybe another sensor is making this failure....
View 14 Replies
I have a 2006 F-350. I got a code p2623 ipr circuit open. I ordered a new one and currently waiting on it. I pulled the old one and the screen has been replaced already. How often do these valves go bad? Is there anything else I should check?
View 6 Replies
2011 6.7... My truck is throwing code P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor. What is the part number for that sensor?
View 6 Replies
I have a 4r100 in my 2000 f250 7.3. I am getting a P1746-EPC Solenoid, open circuit. Does this mean this particular solenoid in the solenoid body has failed and should i replace the solenoid body?
View 3 Replies
My scanner reads P0001 Fuel Volume Regulator Control Circuit Open. My truck shuts down without warning, runs great otherwise. I've changed 2 grey CPS units and now have the Black IH one installed. What the Fuel Volume Reg.is? Is it the IPR on the HPOP?F250SD 7.3 225,000 miles.
View 10 Replies
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
View 2 Replies
I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
View 14 Replies
I have a 2000 F350 7.3 4x4. It began giving intermittent tow/haul flashing light, when going up or down hill but would clear and drive next time truck was cycled off/on. No ABS lights and code reader generated P0720 for the output speed sensor, now I can get it to generate just driving slowly fwd and rev a few times. All of this has been in the last few days.
Truck will stall if I take it up a slight incline with the fault. I replaced the sensor on the top front of the 4r100 transmission and also replaced the sensor on the rear differential after giving up on looking for an output sensor on the transmission. I know the 2WD transmissions have an output sensor but is there one on the 4WD version? I have read several past threads discussing the P0720. I am hoping to confirm what sensor I need to be looking at and where it is located in this application.
View 14 Replies
My 5.4 had a bad miss several months back with no cel. It would barely climb hills it never even needed extra throttle on before (3rd gear, wide open, 35 mph, etc). Ford dealer ran a scan and it had two bad coils and plugs. I changed those and it ran much better, but still had a "pfft pfft" exhaust leak type sound at idle. I checked the exhaust studs and they were all good, so I wrote it off as just a normal exhaust leak.
Full throttle in 5th gear to maintain speed limit when normal throttle before was sufficient. I got home and parked it and it sat over night. I went to start it today and it died. Tried again, died again. It only stays running if I am pressing the gas and I hear a fluttering or air sound of some kind coming from the passenger's side of the engine. It doesn't cut out or miss like a bad coil or plugs, but like you choked off the air supply.
All plugs are still in place, exhaust studs look good, tried it with the air box unhooked to see if it got clogged, and going to check intake leak tomorrow...
View 14 Replies
Having problems with 1999 or later 7.3 missing or dying when you turn on the wiper switch?
View 8 Replies
2009 1.8 Corolla . I'm chasing an intermittent P0352 code and misfire. Code points to coil pack #2 . Question is, which one is #2 ? I want to swap coils and see if the error follows the coil but I can figure out which cylinder is #2 and since all of the coil wires disappear into a loom, I'm not sure how else to tell.
View 2 Replies
Got a 2001 F350 diesel auto, 295k miles.
It has miss when over 2000rpm. Below 2000 its smooth.
ICP has oil in sensor, ordered new one. Gonna change oil too.
CPS is new (not sure if its black or the other one). Starts idles and drives good otherwise.
Where should I look?
View 14 Replies
2010 f250 cc 5.4 145000 miles. I bought it last fall have not drove it a lot. When using the cruise control and a load is added grade or hill in the roadway. It jerks hesitates or miss then cleans up and runs fine. When using the accelerator it does not do this. No codes.... Thinking about changing the plugs.
View 5 Replies
I have a 2000 F350 cab and chassis 4X4 with V10 and a 5 speed manual (actually it's a 4 speed with overdrive). My problem is the engine seems to have a miss in it. When I first start it in the morning it usually runs good for 5+ miles till it warms up then if I am not pulling a load I can hear what sounds like a miss but the truck accelerates fine. If I am pulling a load I can also feel a slight steady consistent shudder and I can tell the truck doesn't have the power it should and the gas mileage SUCKS worse than it use to.
I ran a bottle of Lucas deep clean through a tank of fuel and that seemed to work a little but I will still encounter the problem sometime during the day. When the miss seems to be gone I can hear a very slight pinging noise when I accelerate or pull a hill with and/or with out a load. The pinging noise I hear sounds like an engine with a distributor that is getting to much spark advance if you have ever experienced that before.
I purchased this truck used several years ago and I don't know what the PO did but the check engine light is not coming on and it doesn't throw a code. I put 10 new ford coil packs on it about a year ago so I really don't think it's a coil pack, but I could be wrong. To me it sounds like maybe it an injector problem????? I know there are several sensors on this engine and I am thinking maybe a crank position sensor is not working right but I honestly don't know???? Is there a way to test this sensor?
View 7 Replies
I have a 2000 F-250 V10 that misses (cylinder 10) at the idle, once you give it gas it runs correctly again. I am at a loss. I have replaced the plug, tried moving coils from one cylinder to another to see if it shifts the miss, and it has new injectors. What this could be?
View 9 Replies
ok i was just driving my 2004 ford f150 truck and it stopped running. I turned the key and it started back up again and then while on idle it stopped again. I took it too auto zone and it showed a code of p1237 which as far as i can see says fuel pump secondary circuit failure. does that mean i need a new fuel pump and how hard is it to replace.
View 1 Replies
