Ford Super Duty (1999-2016) :: Instrument Cluster Went Dead?
Jun 7, 2014
So, on my drive home from the pub tonight, my clusters went dead, then came back on, then died again. This behavior repeated for the 5 mile drive home. In addition, I believe the lights weren't working as well. The engine was still running, so I simply continued on home and parked for the night. The only thing I can think of might be the problem is the fact that I replaced the serpentine belt the day before yesterday. Is it possible that the alternator is not charging the battery properly and that is what my problem is?
View 14 Replies
Advertisement
I have 2002 F250 4x4 with 5.4 V8. It has auto locking hubs. If I haven't used the 4wd lately I have to manually lock the hubs in, right side sticks, so I have to use pliers to lock into place. After a few times it works in auto fine. Anyway my issue. I went to use my 4wd so I manually locked the hubs, hopped in the truck and flipped it into 4wd. When I did the instrument cluster died. Radio, power windows and locks, turn signals all work. I just don't have any speedo, tach, fuel gauge, water temp, battery, no odometer. All went blank. I checked some of the fuses that I thought it could be from the owners manual but still no luck.
View 3 Replies
I pushed the Tow/Haul button on the gear shift and my instrument cluster went DEAD. Have checked the 3 fuses labeled instrument panel (F4,F35,F41) and they look OK.
2003 F250 6L diesel .....
View 11 Replies
I have a 2000 f350 XLT SD v10 gas. The radio works, the heater works and the power windows work too. It's just the cluster. Lights work in the cluster it's the gauges are dead truck starts fine.
View 2 Replies
I just bought this 2006 f350 lariat. The instrument cluster, radio, pwr windows (and prob other things) will go dead intermittently. No rime or reason, some days no prob, others, several time a day. Always come back by itself, cycling the power has no effect. I if it is shut down during a no power episode it will not run right till the power comes back to the dash, radio, windows. Looking on line seems to be a common problem with the "retained power accessory relay" circuit in the instrument cluster. I found nothing on a DIY fix...
View 14 Replies
I have a 2012 F350 XLT that came out of Canada. So of course the speedometer is in KM. (Large numbers are km and smaller numbers are mph). I am trying to find out if I can simply change out my cluster with a mph cluster???
View 4 Replies
2003 f350 5.4L auto 4x4. The lights stopped working on the dash so now I can't see the speedo at night. All the dummy lights and gauges work. I checked the 3 fuses for the cluster from the owners manual. All 3 are good. Here's the thing, fuse 35, Checked for continuity, my meter read 192 not all zero's like it should have. I pulled the fuse and rechecked it, it was good.
I replaced it anyway. rechecked with fuse in, I get 192 again. pulled fuse again, checked both sides of socket for voltage and I'm getting 12.64 volts on both sides of the socket. Even though the fuse reads good, could this be the reason my cluster isn't lighting up? Is there a fuse on the back of the cluster?
I see a lot of threads on the cluster lights being out but its usually no tail lights or power windows or other things, and if there's a solution nobody is posting it. Mine is simply no lights on dash or I should say (No Back lighting). All my lights inside and outside work.
View 14 Replies
I am really hoping that my instrument cluster in not working because my alternator went out at the same time. I really hope they are connected somehow. I really need a wiring diagram for this one. Just got the truck last week and have been taking care of the little things to get it fixed up and make it my own. my new rear step bumper came in today. I will be dropping off the the alternator for a rebuild tomorrow. So looking for a wiring diagram?
View 7 Replies
Just the other day I fired the truck up and turned the lights on and my headlights came on but my gauges didn't light up. I figured I probably had a blown fuse or something so I didn't bother checking it immediately and decided to drive home anyways and on the way home I got a phone call saying that my running lights weren't working either. Front or rear. Still have brake lights and turn signals but no running lights. I've checked all the fuses and none of them are blown and I'm going nuts trying to figure out what is wrong before I get a ticket. I'm tired of lightly holding the brake as I pass by cops at night. What could be causing this issue?
View 11 Replies
05 6.0L xlt if that matters. Occasionally, I'll be driving and the speedometer will stick at a certain speed as I slow down. So yesterday it happened again on my way to work, but it was worse. I noticed that as I was driving, the needle was stuck at 0mph. Then a minute later as I was accelerating from a stop, It began working again. A few minutes later, as I was slowing down for a red light, it was stuck at 55mph. As I accelerate again, the needle moves as if 55mph is 0mph. Then it stuck at 85. And as I drive, the needle is just pegged well past 100mph, even though, I'm doing 65-70 max. I have Torque Pro, and all the info from the computer is correct, I can accurately measure my speed from there. Turning the truck off does not reset the needle or anything. It still remains stuck with the truck off, which makes me think it's something mechanical. Eventually, the needle usually lets go and begins working normally for a while.
In addition to the speedo issue, which has happened multiple times, The tachometer was working correctly, then all of a sudden was showing that the RPMs were about 800-1000 lower than normal. When idling, the needle was at zero. When at 65, the needle was around 1000-1100, when it normally reads about 1900. When I left work last night, the tach was fine, but the speedo was still stuck at 85.
It doesn't do it very often, it's just frustrating when it does. All the other gauges seem to function normally. The temp gauges still move, although, I know that means pretty much nothing. The boost gauge is good too.
View 6 Replies
I'm having a little problem with my F350. I've had it for about a month now and the cluster had no problems or whatsoever. Then, I drove it today and I noticed that the instrument cluster is not working at all. The lights work, but the gauges wouldn't move. When I turn the key before starting it the chime is beeping faster than it usually did before and it wouldn't shut off unless I close the door. It also only indicates the airbag and battery light. I checked all the fuses and they were good especially #15 or #16 can't remember it right now.
I don't know if its related, but this past saturday I was messing with the overhead instrument cluster for the gas mileage and all that. I soldered some of the relays back on and that was it. I started the truck after I did all that, but everything was still working. It's been bugging me all day today.
View 3 Replies
My 2014 Super Duty, the accessory delay relay is starting to acted up. When driving my instrument cluster and heater/AC will cut-out momentarily once in awhile. I guess Ford has known about this problem for years and hasn't done anything to fix this known problem in their Super Duties. My truck is almost out of warranty and I guess to fix the accessory delay relay is to replace the whole instrument cluster with a new one with the same defective part. Of course, the accessory delay relay will never acted up a the dealership because it's totally random. Plus, I don't trust the incompetent people who work at my local dealership to do a good job on tearing out my trucks interior and to get it back together like factory. I'm at a loss.
View 10 Replies
I have a 2001 F350 and instrument cluster lights will not work. Fuses are good and the gauges still work just not the lights.
View 5 Replies
My wifes truck is having some issues right now. Last week I was driving it down the highway, and the gauges all went off, the door buzzer was sounding, and the door locks where going up and down constant when I had my foot off the gas pedal. Found the fuse and fixed it with a replacement, but its down it three times all together since then?
View 9 Replies
I will change the cluster lights to blue LEDs.
Some "leftover" questions:
How do I get the needles "clear" instead of red?
How to remove and reinstall the needles the "right way" (e.g. calibration)
Everything else I could find here in different posts.
View 2 Replies
I found one thread in FTE regarding replacing instrument cluster bulbs but the solution was to contact Circuit Board Medics. I have one dark area on the right side of the tach and another dark area on the left side of the speedo. Probably the same bulb that's out. Also, can attempt to replace the bulbs (assuming its a bulb and not a fiber optic of some sort) in the steering wheel volume and fan controls?
View 3 Replies
I have a 2003 F550 6L diesel flatbed truck. Last week, the overdrive button would activate by itself. I'm assuming there was a loose wire so I taped the button to keep the overdrive off. Two days later, the overdrive came on while the button was pressed in and then smoke came out of the steering column/lever area. I pulled over and turned off the truck. The smoke stopped after 10 seconds and I restarted the truck. The overdrive light/functionality no longer worked and the instrument cluster also wasn't working.
The next day I was driving, and the truck died at a stoplight. I got it towed home, and opened the steering column and noticed that the overdrive button wire had burned. I removed the harness clip and charged the batteries. It started but the instrument cluster still didn't work. 2 minutes later the truck died. I replaced the alternator but still it won't charge the batteries. The truck dies 2 minutes after getting a battery boost to start the truck. The instrument cluster also doesn't work. What could be causing this issue?
View 1 Replies
I have a 2004 f 450 cab and chassis truck that the problem started out with the radio not coming on. So I asked the local dealer and he gave me a wiring diagram. I pulled the fuse box out and checked the wire from the fuse box to the radio and it works. Great. But he also said I could take the fuse box apart and check to see if their was a broken connection in it. So I did and could only get so far with it. It has a lot of pin on one side that go all the always through and are soldered on both ends. So I put it all back together and reinstalled it. Now the instrument cluster does not work. Not even the warning lights. The interior light doesn't come on either or the door chime. Is it possible to melt the solder off and open the fuse box completely and check all the connections.
View 1 Replies
I have a 2005 F 350 with a 6.0 Diesel! My heat quit on my wife and I the other night! I replaced some fuses and started the truck to make sure the heat was working and it was! So I thought while I am here I should replace some bulbs in the cluster that were out!
I took the cluster out, looked at the bulbs and they looked oK so I put them back in and put the dash back together! When I went to start the truck once I turned the switch on my gauges and lights started flickering on and off fast and all it will do is just click when I try to start it! I just had it running 15 minutes before this!
I went through all the fuses and if I take one of the relays out and turn the switch on all the lights and gauges seem to work right but when I try to start it, nothing! I replaced the relay and it starts flickering again! I had the relay checked at Napa and they said it was good! The relay was for the Powertrain module!
View 2 Replies
Is there one fuse for the entire instrument cluster? Because today the entire instrument cluster went dead, even the digital odometer part. Hoping it is just a simple blown fuse...
View 14 Replies
I have a 1999(03/98 Production Date) F350 DRW Dump 5.4L Reg Cab. I just replaced the ECM (Drivers side Kick plate) with a used ECM
1. Crank but no start, gauges worked.
2. Replaced the ECM (Drivers side Kick plate) with a used ECM
3. Truck now starts.
4. None of the Instrument gauges work. No gas gauge, no speedo, no tach, no bat no odometer or trip odometer. Not one single gauge works.
Does the ECM need to flashed for the cluster to work or might it be a separate issue?
View 2 Replies
