Ford Super Duty (1999-2016) :: Installing Puddle Lights?
Mar 22, 2014
I am going to be installing puddle lights to light up my step bars and I am looking to find out which wire to tie into? I was going to tie into the dome light circuit (blk/blue) so they would come on with keyless entry door unlock, but my dome light won't come on. So I either have to figure that out or go to plan B and find a difference source. Adding lights down there and found another way to power these? I don't know if extended cabs ever had the option for lighted running boards, maybe there is a dedicated wire somewhere? I don't want them on all the time, only when the truck is unlocked to light the step.
View 12 Replies
Advertisement
I just picked up a 2001 Ford F350 4x4 7.3 SRW last week. I've been slowly going through the truck replacing everything. One thing I've always liked on trucks is the cab clearance lights, which this one doesn't have (it's a base XLT with no options).
So I looked on Amazon and ended up ordering this....
But then I realized that the harness isn't included, and I can't find it for sale anywhere. I searched the Ford parts site but can't seem to find it.
I'm thinking about returning those lights and getting this set: [URL] .... But I'm not 100% sure that the harness that's included will fit my truck, it only says Ford.
View 7 Replies
My truck had a small puddle of anti-freeze under it last week. It has been sitting for a couple of weeks with no issues until I noticed the puddle. After I cleaned it up, it hasn't leaked for a few days. I obviously can't find a source. What could have caused it to leak and then suddenly stop?
View 2 Replies
I have a 1999 f-250 sd 4x4 that had a 5.4L auto trans and a switch operated transfer case. Im installing a 1998 12v Cummins, nv4500 5 speed, and dodge manual shift transfer case. My father and I have made engine mounts, modified trans cross member, and installed a 1/2 " dip tube into fuel tank an used 1/2" fuel line to connect to factory Cummins fuel line. We are now to the worst part now "WIRING". I still have the OEM gasser 5.4 wiring harness. I bought bushings to install ford coolant temp probe and ford oil pressured sensor. I got my harmonic balancer machined with 2 more notches for ford cam/crank sensor pickups but I'm just confused after reading a few different postings about tach. I guess just need a run down on the 12v wiring to the 5.4 pcm. I would like all factory dash gauges to work right, cruise control, and A/C to work. My 12v still has dodge alt and dodge a/c compressor. I ve bought a bunch of parts so after you post to this ill let you know if I have it or not. Things like ford clutch and brake pedal sets, ford OEM manual transfer case shifter setup, bushings for ford sensors to Cummins, and other things I've forgot about.
View 6 Replies
The V10 in my service truck took the long slow ride. I located and am in the middle of replacing said engine. My question is, how difficult would it be to install a second alternator in this truck, considering I have it torn down for replacement?
It a 2000 F350 with a V10. I'm looking for more power as I have mounted on the Knaphiede service body a IMT 1015 crane, 3200 lb capacity. I would like to install a power inverter to be able to run an air compressor in the field.
Am I looking for a new harness? Etc?
View 5 Replies
I had my leveling kit installed today. Bilstein 2" leveling coils, adjustable track bar, 4" rear blocks, and shocks front and rear.
I have 295/70/18 tires on stock wheels that didn't rub anywhere before. Now at full lock to the left the drivers side tire just barely rubs on the radius arm. How is that possible? I was planning on getting 35s soon when these wear out but it seems like those would rub even worse.
View 8 Replies
How much better stopping power can be achieved by installing an upgrade brake kit? There are several kits on the web. Upgrade kit? Pros/Cons.
View 14 Replies
I have a 1999 ford f250 superduty extended cab and am trying to find possible subwoofer locations (not wanting to lose floor space) but I can't find any pre-made boxes. Any pictures I can use as reference. Really wanting to install subwoofers. What can I do?
View 10 Replies
I just purchased a donor wheel from ebay... it was the right price, and I'll turn around and sell the shell and the switches when I pull the wires out.
I'm looking forward to the wheel getting here. I expect to be able to swap the wiring harness inside the wheel and then be able to add the redundant audio control switches. This should leave me with the impossible setup of having a black vinyl wheel with cruise and audio controls.
View 14 Replies
When installing front lift shackles, do you place jack stands under the axle, or the frame? I can't really find an answer. I assumed the axle, but i saw a thread and from what i could see it looked like it was supported at the frame and the axle was hanging free in the air. Just want to be sure before i start unbolting the stock shackles tomorrow and kill myself.
View 14 Replies
I was wondering if there was a DIY mod so I can have my foglights on with my parking lights and my high beams..
View 7 Replies
Should the indicator above reads "4x2, 4x4 hi, 4x4 low" light up when the driving lights (i.e. at night) switch is on?
If yes, how to change the light bulb?
View 10 Replies
2013 F250 XL with factory towing package.
My camper and boat trailer do not have turning signal or brake lights when plugged into the round seven pin trailer connector. I have tried both the connector in the bed and under the bumper. I've also connected the trailers to other trucks and the lights work fine so I know the problem is in my truck.
View 9 Replies
The rear tail lights on my truck have been out for a while now. I wasn't doing much driving at night so it wasn't much of a bother but the new job is getting me home a little later and having to drive with my hazards on is getting old fast.
My radio wasn't working either and I disconnected it a while back hoping maybe it had something to do with my lights shorting out but no luck. It remains disconnected. Just in the past few days my front running lights have went out as well.
I've tested all fuses multiple times (and replaced a couple of them) and checked and replaced bulbs. My brake lights, headlights, dash lights and hazards all work fine. I have the trailer light hook up on the rear bumper and disconnected it at the wiring harness as well hoping it was the problem but it wasn't.
View 3 Replies
I installed after market HID lights (Including light Assy) and there re no adjustments on the new housing, right now they are close but the passenger side is shinning high. Am I screwed and there is nothing I can do?
View 3 Replies
99 f350 7.3... All lights working but running lights wont go off....
View 1 Replies
A few of my clearance lights have gone out... and I'm looking to replace them. I was told the bulb type was "194" and was wondering if I could just drop in some 194 type LED bulbs like these, in amber color without changing anything else [URL] ..... I'm assuming it will plug right in but wanted to make sure
View 14 Replies
On the 99-07 front bumper i would like to add driving lights in the bumper under the headlights something like the 11 up bumpers have...
Looking for a light and housing that possibly could be installed with out having to re chrome, so it could have a bezel to cover cut edge of bumper...
View 4 Replies
I left town tonight and dad called to say I had no tail lights. I stopped and checked the book to see where the fuse is and couldn't find anything for the tail lights or parking lamps. I have brake lights, both rear turn signals and the tail lights blink when you lock it with the fob. The trailer socket shows I have trailer tail/marker working. Why don't my tail lights work?
View 14 Replies
Two days ago I noticed that I had one of my cargo lights that didn't light up---I took the light off and the bulb was blown, and other was OK. I picked up a couple of bulbs and I replaced both of them. Now, neither one will burn. I checked the bulbs with an ohm meter--they were good---checked the #10 fuse at the passenger kick panel and all OK, but I don't have voltage at the light sockets now. If the bulbs I used were a greater wattage than the originals, would that have sent an overload signal to the SJB (smart junction box) and stopped the supply of power to the lights? I'm tempted to put it right back where I started, with the one good, used bulb and see what happens then.
View 2 Replies
My 08 F3 50 seems to be turning the lights on and off by themselves throughout the course of the evening and the day currently I am disconnecting the negative cable trying to trace back a bad ground I'm not exactly sure what I'm doing
View 2 Replies
