Ford Super Duty (1999-2016) :: Head Gasket Failure - Oil Leak
Feb 25, 2016
2001 Ford F250 5.4 gasoline. At the most recent oil change my mechanic said there was an oil leak and he had dyed the new oil and cleaned everything up and to come back in 100 miles.I just did so and he said that it was a leaking head gasket. He said to do the head gasket replacement right or to put in a rebuilt engine would be close to same and he would recommend the replacement. He said it was not a heavy leak and probably ok to drive another 10,000 or so miles first. Just returned from a trip where we drove 15 hours straight (30 degree temps) and the truck ran fine and no overheating.There does not appear to be oil in coolant or vice versa. I took the cap off overflow coolant and cranked and revved and no disturbance whatsoever. I read somewhere where a mechanic was saying it was impossible for this Ford engine to leak oil from a head gasket failure .
View 7 Replies
Advertisement
I've been trying to figure out what is going on with my '99 F-250 V10, you can check out this thread for the back story
[URL]....
I did a compression check and the results seem inconclusive to me- see image.
Before I did the compression check I started to take the intake manifold off to change the gasket set and it's about 50% done. I'm at a crossroad now. Do you think I should finish switching out the intake gaskets or do you think it's more than likely a head gasket? I would hate to put it back together, it still smoke and have to take the intake and everything else back off to do the head gaskets.
Someone had mentioned a possible small crack in the cylinder wall that is closing up when the engine gets heat in it and obviously doing the intake and cylinder head gaskets would fix it if that's the problem.
View 14 Replies
my truck at 210k miles got a new radiator (seeping at seams), thermostat, water pump (bearings shot, leaking), intake manifold (The crossover was leaking). It now has 227k miles. Oil leak in rear at head gasket by starter (bad head gasket?) It overheated the other day( blowing coolant out the expansion tank needle in the red) Replaced thermostat. Drove around for two full hours, seemed fine, Drove to work today it overheated ( same thing, blowing coolant needle pegged) didn't make it to work. There are no external leaks and its not putting steam or white smoke out the exhaust. I read somewhere that a blown head gasket could make the truck overheat, is that possible? What all could cause this problem?
View 6 Replies
how difficult is a in frame head gasket repair?
View 6 Replies
Back Story: Ok so in my infinite wisdom I let myself get distracted when I was looking at an 01 F250 V10 Crew Cab. I thought, it needed all new breaks/rotor & 2 calipers. And new carpet and seats, then I would have a good hunting rig.
So I went and looked at the truck in the dark (first mistake). The guy was very honest with me and told me about all the body and interior issues. Even informed me of the caliper that he disconnected because he could not afford to fix it. He informed me that it did burn a little oil and it's been a while since he checked the oil. Well at that point I was going to look under the oil cap to check for any milky residue. Well I got distracted (Second Mistake).
So here we are 2 weeks after getting bringing the truck home. I already replaced the carpet and seats, breaks & rotor & 2 calipers. Well today I decided to go get some new oil and a filter, and do a quick oil change since who knows when it was done last.
Issue:While draining the Oil it seemed like there was an abnormally large amount of oil in this engine. (See photo of bucket full of oil from this rig.) Well didn't think much of it and swapped the filter. And went to add new oil to the engine and found that under the cap was some milky substance.
The V10 has 420K original miles. I have heard that is no big for the V10 but thought it would be good to note this detail. Questions I have: Should I get some kind of test kit to confirm it's a blown head gasket? If so what kind of Kit should I look for? Do you think this truck is worth replacing the head gasket?
Any chance this may just be a known issue for the V10 and I just need to replace some kind of valve? I could not find any you tube videos of a head gasket replacement on a V10 any thoughts where I should look?
My Skills: Just to be clear I don't know anything about the V10 motor. I have a 94 f-250 but have never had to dive in to a head gasket replacement before. I have done a head gasket replacement on smaller engines (IE: car and a jeep) but those were obvious that they had a bad head gasket.
View 10 Replies
I thought I needed a head kit my truck runs and drives great till I run out of coolant no smoke doesn't get hot I run out of coolant I lose my turbo. Pull over fill it up I'm back to normal I just noticed I have sweat marks on my water pump pulley.
View 6 Replies
Have my oil leaking-passenger side head gasket replaced (along with the drivers side for preventative measures).
To ease my mind at such an expensive repair on a truck I just recently bought, I was wondering what else gets replaced with this repair.
Obviously the head gaskets along with head studs, coolant and oil, but anything else? valve cover gaskets? intake gasket?
View 14 Replies
To all those folks that said I had a head gasket putting pressure into my cooling system and causing it to overheat, you were right. It is a 2003 F250 with 80000 5.4 l. I have had to replace mexhaust manifold bolts on left side (horrible job, couldn't get one out). Back fenders are rusted out, under the extended cab rusted, doors are rusting at the bottom. My friend/mechanic said it was time to get rid of it. I don't really have thousands of $$ for a different one, but also, replacing the head gaskets are in the thousands for a repair bill. I have looked at used 2008 250 4 door and they are 20000+++ sheesh, but a new one is out of the question. Do I get the gasket situation repaired?
It does not act up all the time, some times it never overheats, sometimes it will. Somewhat infrequent ( I had one mechanic look at it and he tried 3 different times, and it did not overheat. Temp gage will peg, coolant resevior will overflow, but is not hot (100 degrees). I dont have the really have the money to put into a newer model, but I am worried about being nickeled and dimed to death after dumping a couple of thousand into a head gasket, plus I suppose I need to have the other side manifold gasket/bolts checked too. It seems like low miles to be having issues, yes I realize all will rust, but this year, as evidnet in our area, was really suspect-able to rust.
Not worried about the body, is it worth it to spend 2500 for head gasket repair, or trade up a couple of years, less miles, etc. My worry is, I already had to fix 1 exhaust manifold gasket, know head gasket to fix a cooling issue, do I cut my losses and move to another truck, or spend the money for repairs. I don't really have money for either but want to make a good decision. Truck has not been abused and has been serviced as scheduled. Had to put on new brakes and rotors, as would expect, and ball joints too. Oil looks fine, no contamination, and coolant is clear. Will the head gasket get worse? As I said before, it is intermittent, but I don't trust it for long trips.
View 9 Replies
2005 FORD F350 Lariat 6.0, 61,000 miles, and in prestine condition. Just got the news the head gasket is blown! HOW DID THIS HAPPEN?!!! My mechanic says to scrap the whole engine because the 6.0 is the worst engine around. This truck should last for years!!!!!
View 14 Replies
I am replacing the head gaskets on a 2006 Ford F250 6.0 .... I have heard that I should replace the head bolts with studs. Do I torque the studs just like the bolts?
View 5 Replies
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 Replies
So I've put about 1000 miles on my 03 F250 since buying it, and just the other day it's started leaking from the rear of the passenger head gasket. Enough to drip on the driveway and exhaust, and have some exhaust smell. 126,000 miles, 5.4
I've checked with my local ford dealer, and It also needs passenger exhaust manifold and studs, so the dealer price to tack that on would be a whole lot more too since there are already a couple studs broke. It would be best to get it done when the head is pulled.
I've checked with several local mechanics, and none of them are interested in pulling the head on this engine. That has me concerned about doing it myself too..especially since it fits in my garage with only a few inches to spare..
View 14 Replies
I have been having non-stop issues with my tranny. After getting it rebuilt (by some BS shop my warranty company told me to go to) it is starting to leak when parked for more than a day. It generally pisses out about 1/2 to 1 qt overnight when this happens. I crawled under the truck and it looked like the fluid was coming from the pan gasket. Rather than taking it back to the mechanic that decided to take 3 months to fix it last time, I swapped out the gasket myself. This did not solve the problem. Where and why else could it be leaking from? It is not over filled, I have checked multiple times. I would prefer not to have to hand my truck back over to the incompetent 'mechanic' that 'fixed' it last time.
View 14 Replies
I have a 2006 f250 6.0l diesel. I just replaced the egr valve plus egr cooler and I was going to flush the coolant. I was filling the truck with distilled water to do the flush when I noticed a leak under the truck. When looked to see where it was coming from it looks like it's coming from where the cylinder head meets the block on both sides in the back by the transmission. Is this a sign that the head gaskets are shot or did I forgot to tighten a hose or something stupid like that?
View 2 Replies
1999 f250 with some mild upgrades. Trucks got 189,000 miles. Stole it from an older guy for 4k. In fantastic shape. As the weather got colder I noticed an exhaust leak. Took it to a muffler shop only to find that it's got an aftermarket header on the passenger side only. Is that common to replace only one side?. the gasket has gone bad and needs replacement. I wanna replace both headers?
View 8 Replies
I have a leak from the oil pan gasket and oil coolant lines. From the research I have done, it looks like I have to lift the motor to change the oil pan gasket. Any way to get this done without lifting the motor??? 2000 f250 5.4 2wd....
View 4 Replies
I have a oil leak that I can't seem to find the source of. The head gasket corner (driver side firewall corner) has oil on it. (3.8 SC). Or maybe the intake valley gaskets are leaking but it doesn't appear so (and the intake was done within the last 20k miles). The back side of the oil pan (toward rear of car) is wet and the oil seems to be dripping off the transmission pan somehow.
Another thing is the knock sensor between the block and transmission seems wet, not sure if the oil is coming from above that or not, would the knock sensor leak oil or coolant? (or nothing)...
View 6 Replies
Early 04 but 06 motor, Coolant filter, BPD EGR cooler, Head studs. I did use the search tool, overloaded with EGR cooler leaks and head gasket failure in the results.
Noticed ECT Spiking 217 (EOT 187)as went to post office,10 min run time from a cold start. Checked Degas a bit low, did my business and went home. Got home ECT 223 EOT(221) zero coolant in Degas and notice this mess. as well as puddling up under radiator.
I left the truck running and added some water to the degas hoping I could spot the leak, no love.
On our trucks do we have a weep hole for the water pump? I didn't notice any water or stains around it or the pulley. Nothing around the hoses either... yet.
Once it cools I am going to pull the fan shroud and look for a possible hole in radiator. Are there any other suspect areas?
View 7 Replies
my oil pan gasket is leaking on my 2002 f350 5.4l 4x4. I have read lots of threads on replacing this gasket on an f150 but haven't seen one for an f250/350. so what is the procedure to do this job on an f350?
View 2 Replies
I get allot of questions on just what to check when you get the ipr off the vehicle so you know if it is bad or not. In this video I go over what to look for in depth with an example of how a failure looks.
[URL]
View 1 Replies
So my issue, had heat last year, turned on first time this year and its cold. So I did some research on the site and have done a few things but still no heat
First thing I did was flushed coolant system and add new coolant as I have 235,000 miles on the truck and it looked rough
Ran the truck for a while and checked heater core hoses, they were both warm, not hot by any means so I pulled the thermostat and replaced the thermostat and gasket
Now the hoses to heater core are both hot and my temp gauge went up about 1/4" higher than it ever has, but still no heat.
Blows fine, just cold or sometimes luke warm. I pulled the glove box back to try and see I I could hear anything when I change from hot to cold and I hear or see nothing. Only movement I see is when changing cycles from defrost, heater, ac... So could this be a blend door issue an how do I get to the blend door, is it behind the big plastic plenum box?
View 14 Replies
