Recently purchased a 99 F250 SD w/ V-10 Triton which purrs like a kitten and drives great until I turn it off and then re-start. It has trouble re-starting and then when started and put in drive...won't go anywhere. Zero power. Oddly, in reverse it goes. Getting decent flow from exhaust. No vacuum leaks I can find. No check engine light on either. Strange.
View 7 RepliesI recently purchased a 00 F250 psd 4x4. Other than doing all of the fixes it needs to make it ride better I have been questioning the trucks "get up and go" and the EXTREMELY sensitive skinny pedal. Truck seems to pull very hard and puts out some black smoke under hard throttle but nothing like the really tuned trucks I have seen. But the skinny is so sensitive its hard to drive under 40mph in 3rd and once it gets up to 55 or so its real sharp getting on and off the throttle. Trans shifts great, TC locks and unlocks, truck runs awesome IMO but just a bit harsh. Is there a way to find out if it was tuned prior to me buying it other than inspecting for a chip, or is this the way they are and I just have to get used to it more...?
View 9 RepliesI have a 2006 F250 Lariat super Duty / 6.0 L engine / 143000+ miles / once started and transmission shifted into drive it takes 5 seconds or more for it to engage hard or if I build up the RMS then it jumps into gear hard, after it gets going it feels like I am driving on a washboard until it get warmed up good 10 mile or so. Is it the transmission filter and if so which one, I understand there is a small one on the outside of the transmission if so where? I can't find it.
View 14 RepliesTruck: 1999 Ford Truck F 350 4WD Super Duty V8-7.3L DSL Turbo VIN F
Problem: Especially when it is cold outside . . . The truck takes forever to start and while doing so a ton of white/grey smoke comes out of the exhaust.
My starting schema: Turn the key on have the gas pedal pushed to the floor until the "wait to start" light goes out. Then, I turn the key off and back on while still pressing the gas pedal all the way down. When the "wait to start" light goes out again I remove my foot from the pedal and try to start it. I never leave it cranking for more than 5-7 seconds. If, after trying this process several times I will not push the pedal in at all. Also, sometimes I will leave the pedal pushed in while I am cranking it over.
The truck used to start after a couple of tries but lately it won't start at all, even after 20 tries. Sometimes it will spin up for a second as if the engine gets going but then just doesn't continue running. When it is warm out it will usually start after a few tries but doesn't seem normal to me. After I first bought the truck(used) it would start up within half a second after turning the key.This all started after I had to fix an o-ring that was damaged on the top/back of the motor that was dumping all my oil out of the top/back of the motor.
Bought 02 350 DRW, started hard first day, now not cranking. Seen a post on neutral transmission switch and mine is not lining up, but need to adjust the rod out of transmission also? I was able to match lines on switch but with flanges on fitting it will move back out of place when moving it to fit in bolts.
View 4 RepliesI've been having sporadic starting issues with my truck since the fall. I had the spark plugs changed but that did not work. The hard starts usually occur when the engine is hot....after filling gas or just running into the grocery store. The engine seems to turn over slowly the first try and won't start. The second or third try the engine turns over normally and the truck usually starts.
I just got back from a 90 minute drive and shut off the truck for 5 minutes and now it won't even turn over. My thought is that it can't be the battery....its been charging for 90 minutes. Headlights are strong, wipers work fast, fan blows hard. That being said I think alternator or battery can be ruled out?
Where do I look next? Starter? Is there a starter solenoid that could be defective?
My '01 f250 7.3 has gotten hard to start. It seems to maybe be due to cooler weather, but not always. I have been told that there is some sort of valve in the fuel tank that could possibly cause this when the fuel gets around a 1/4 tank or so. But, it's doing it at any fuel level. But it doesn't do it all the time. I do notice it more in cooler weather. Anyway, when I try to crank it, I'll let the "wait to start" light go off and then wait a bit more. I'll turn it over and it almost as if the batteries are weak.
I'll stop and give it a few seconds and turn it again and it will normally start. But sometimes I'll do this 5 or 6 times and it will finally fire. But the more I have to try, it's like fuel builds in the cylinders and it smoke like a coal train for a minute or so. Almost like gas motor that has been flooded. But the smoke burns off and it runs like a top. I was thinking the batteries may be weak , but sometimes the starter will spin the motor with no trouble at all. I'm at a loss. Is it possible for fuel to drain from the system causing it to have to reprime itself? Here lately the smoking has me concerned even though it clears up.
06 F250 6.0 with only 65,xxx miles on it. This has happened twice and both times the engine was warm and had been cut off for less than 10 min.. When I tried to crank it back up it stumbled and idle roughly then cut off. After several attempts to re-crank it still would idle rough and I tried to give it fuel but no change, even with pedal fully depressed. Then it would die.
After sitting a few minutes it starts normal. Both times I didn't have my obd2 adapter for my torque pro. The last time it happened I went home and hooked it up and got no codes. Everything looked fine. What could it be, where should I start looking. Batteries are1.5 years old. Oil, oil filter, and both fuel filter changed about 1000 miles back. I have had the truck for 1.5 years and the oil has been changed twice.
As a follow up to my problem of intermittent stall and hard start, it is getting more pronounced. Now, every once in a while, it will start. Mostly it will not start.
This morning I connected an OBD2 meter with the key on and engine off. It told me that there are no DTC's. As I was attempting to run enhanced DTC's the code reader lost link with the computer. The connection icon was on but it lost the link. At one point, after several tries, I got the link back but it didn't last too long before it was lost again.
This is the same symptom that I have with running the engine. It will run and then shut off. After a hard start, it will start and run just fine and then shut off again.
My question is this. Can I still have power to the PCM and loose power to the processor? Is there a fuse or relay that could be causing this problem? If not, could the problem be a faulty PCM.
i have a f350 superduty with a 7.3 turbo diesel and I pretty much hafta keep it plugged in to get it to start, i have installed all new glow plugs and both relays have been changed and the problem is still there, only other option i have not tried yet was changing the pcm controller but unsure if that is the problem ..
View 14 RepliesI have a 2004 F250 5.4 gasser, 214K on it. It is my daily driver, and it gets around 6mpg. I feel like this is a lot less then it should get. However that's not the only problem. it wasn't always this bad, but now almost every time I start it, it cranks and cranks and cranks but wont start. I turn the key back, forward again, it turns over 2 or 3 times, and starts, but kind of spits and sputters at a low rpm before speeding up the rpms. I feel like these issues are linked, but its pretty annoying that the starting issue happens everyday. Its been doing this for about 3 years now and I feel like one day it will let me down. People start looking at me if I have to try to start it 2 or 3 times.
View 1 RepliesI like to keep my GPS in the tray on top of the dash, mounted on a sandbag-type mount. I want to hardwire the power (I already know how to do this at the fuse panel) but need to find a way to have the power cable through the tray. Any cool ideas other than drilling a hole and using a rubber grommet to clean up the pass through?
View 9 Replies I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
I started having a issue with getting my 00 f250 power stroke to start. It started out I could move around the gear shifter in park and get it start and today I had several times I had to put it in neutral to get it to crank. I did notice that my shifter on the column seemed to have some play when in gear but then again my 99 F250 V10 also has some free movement when in gear. Is there a neutral safety switch I could replace or any way to adjust the shifter?
View 14 RepliesDealing with a 02 f350 7.3 powerstroke . The engine cranks fine . It fires but won't start smoke coming from exhaust while cranking and firing so seems to have good fuel . When it does start it misses for a few minutes and blue/white smoke . When the miss ends so does the smoke and starts fine after that and runs great until it sits for 12 or more hrs . Then back to same start issues . Fresh oil ,new glow plugs, new cover gaskets , glow plugs test at 1.3 ohm across all 8 of them , no voltage drop through glow plug relay , good voltage to each glow plug when tested right at glow plug terminal on each feed right at glow plug , fuel filter housing stays full doesn't seem to bleed back , high pressure oil pump pressure test was high enough to trash a 1000 lbs gauge in 2 to 3 revalutions of engine when cranking . Tested at presure sensor port .
View 2 RepliesI have a ford f350 super duty that has a little problem turning to the left but is really hard to turn to the right. How do I fix this?
View 4 RepliesBeen driving my 2001 f250 7.3 4x4 with no problems then started noticing it lacking power so I changed fuel filter and air filter. After a week goes by I was at work and I was leaving to come home so I started truck to let warm up and it cranked longer than normal but started. Let run about 10 minutes idle nicely when I punched it it bogged down and had no power never died. I idled over into parking lot and power came so I took off again loss all power again, still never died. Got it right back to my work sat there a bit and tried again this time I took it easy and was able to get my truck home 30 so miles.
When I got home I ran codes p1211 came up for the icp sensor I changed it did not change anything still had same problem. This was a Saturday afternoon to evening issue. So sunday I played around with it just checking out info online and test driving it seem to run ok but still lacking power. Let it sit till Monday I went out to start it had to cycle key 3 time before it started idle nicely then died would not restart changed ipr valve nothing changed cam sensor nothing changed some how 10 quarts low in oil just changed dec. 30th don't know ? Now will start if I pump throttle and has all its power back?
Every time I try turning at idle or with foot on brake it wont turn at all. Is this just a super duty thing or vacuum leak or power steering pump going?
View 9 RepliesI have a 1999 Ford F250 super duty 4wheel drive, lifted (really a leveling kit but had to lift rear to compensate), 5.4l. Im having a problem with my front shaft turning while in 2 wheel drive. Hubs aren't locked and its in 2 wheel not 4. I've taken hubs off and the bearing spins free soo I know its in auto. Why is the drive shaft still turning???????
View 5 RepliesI need fixing my 2003 f350 6.0 diesel, I have been working on this truck for a while and still am having problems, here was the original symptoms:
-Hard start or no start on a sunny day
-Rough idle for 10-15 minutes
-Rough shaking in the low RPMs (35 mph)[/COLOR]
-Slow response from the gas pedal
-boost would only get to 14
My dad and I then did many things to the truck in the shop, those things are:
-Air test and replacement of coupling going into oil branches (next to HPOP)
-Replaced EGR valve (no good)
-Replaced ICP sensor (leaking oil)
-Replaced ICP sensor and IPR valve piggtails (due to frayed wires)
-Cleaned Turbo
-Cut MAP sensor hose and reattached it (spliced on the end)
-New battery
-Performed a bubble test and found two bad injectors on passenger side (injectors #5 and #7)
-Cleaned and lubed tops of injectors
-Replaced O rings and copper crush washers on all injectors
-Replaced nipple cup O rings (tight)
-Blew out injector cups
-Bubble tested after injectors put back in (no more bubbles)
-New FICM, EGR cooler and oil cooler were already installed
-Ohm'd main engine wiring harness (good to go)
-Taped up frayed wires on fan clutch connection
-Increased wire gauge on the positive jumper between both batteries
-Sanded each ground on the batteries and engine, cleaned battery clamps, lithium greased connection points.
-Checked fuel for air (no air)
-Checked fuel psi (85 psi, plenty)
-Oil changed
After doing all of this (diagnosing as we fixed each thing) we now fixed many things including the hard/no start problem. Now, for the first three to five minutes:
-It starts right up
-Runs perfectly, no shake and instant response from the gas pedal and turbo
-Boost goes to 28
-ICP is 800-950 on idle
-IPR is 25-26.9% closed
After five minutes however:
-Starts to shake
-IPR % starts to raise
-Received no response from gas pedal (absolutely no power)
This truck has been torn apart like 8 times and I have to do it on my spare time.
I'm working on a 2000 7.3 that was running but had no power so we changed out all the injectors and glow plugs and rebuilt the turbo now there is no start ...
View 2 Replies