Ford Super Duty (1999-2016) :: Grinding Noise In Left Front When Slowing And Stopping
Oct 7, 2016
TRUCK: 2003 F250 S/C Long bed 4x4 7.3 Diesel
PROBLEM: grinding noise in left front when slowing and stopping.
Starts as a howling noise, turns into a grinding as you brake and come to a stop. I feel it in the pedal and as it slows it feels like metal to metal brakes
WHAT HAVE WE DONE: Replaced both front hub assemblies (MOOG)... Replaced dust shields, rotors, calipers, pads as well as all new brake hardware.
At any speed when I brake hard it grinds and howls, I have taken out the 4x4 locking hub assembly and it does not change the situation. I am stumped!
View 6 Replies
Advertisement
I replaced both front bearings, calipers, brake pads, now I have a grinding noise on the left side front stops sometimes when you step on the brakes? 1999 F350 ...
View 6 Replies
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 Replies
I have a 2005 F-250 4x4 and recently i noticed a grinding noise while driving and then when I come to a stop I hear a clunk and the grinding stops. It sounded like it came from the driver side wheel so I changed the wheel bearing assembly. About 3 days later it started again. Now it sounds like it's coming from both sides. I am at a loss. The hubs are unlocked. It's hard to describe the sound but to me it sounds like 2 gears with a large chain rotating on them. I hope that made sense. The clunk can be felt in the brake pedal.
View 2 Replies
I have a 2003 f250 with the 7.3 power stroke in it. It is factory height on a set of 285/75 16 tires. It already has a reman steering pump and I replaced the steering gearbox today due to the truck having a little slop in the wheel. Since I bought the truck it is dang near impossible to park in a parking lot and almost impossible at a stop sign or being stopped to get it to turn whether I'm on the brakes or not it doesn't seem to make a difference. What else could be affecting the steering on the truck? All the steering components are good. I'm about by to the point of just selling the truck because it's that hard to steer. Especially trying to back a trailer is hard too.
View 9 Replies
My dually has started to make a rubbing or grinding noise just about every time I make a turn, left or right. What this could be, truck has 8500 miles on it.
SD Dually
View 9 Replies
First off my trucks a 2000 v10 f250 with four-wheel drive and 2 wheel abs with about 230000 miles on it.
I Recently replaced my unit bearing on my drivers side because I thought it was the cause of a grinding that only happens on hard left turns but I wasnt the cause it was going bad causing play in the half shaft. I didnt seem to notice and wear on the shaft from bad needle bearings but I have to take it all apart again to be sure. Was just wondering what else could be the cause of this noise. I plan to pull the axel shaft and change all the seals.
View 3 Replies
1999 f250 super Duty V10... I am having some problems with switching out of four wheel drive. S, when I flip the switch back to 2 wheel drive everything, seems ok at first, but within a mile or two I will hear this grinding coming from the front that sounds like the gears aren't completely disengaging. The inky thing that prevents this grinding from happening is switching back into fire wheel drive and keeping it there. What might be causing it to not stay disengaged ?
View 1 Replies
For starters I have a 1999 F-250 5.4l changed all 4 ball joints about 15,000 miles ago. I have been hearing a grinding noise coming from the front end for the last month only when I turn left and at slow speeds. I was servicing the TC so I threw it in 4 wheel to check it and it wouldn't engage until I started moving. When it did engage it was a bad grinding/ clunking sound coming from maybe the differential.
View 14 Replies
2012 F450 Dually King Ranch 4x4 - I have read many threads on front end noise. I started hearing a noise when I turned left or right and then slowly run over a speed bump. I listen to music at an average sound and I picked up on the front end noise. For some reason you can hear it in the driver seat better.
Anyway I took the vehicle in and the mechanic said he didn't hear anything. I thought, he forget his hearing aid today? I have this expensive warranty plan that would actually cover a few items in the front end but Ford is claiming they don't hear anything.
In their defense I have figured it out why. When the temps are below 40 the noise gets louder and I think by the time they looked at it (8 hours after I brought it in, 5:00pm) the day was warmer.
View 11 Replies
Last couple drives I have noticed some front end noise on the left side. Back in May I also noticed grease all over behind the rotor. I believe this is the grease inserted via ABS hole into the unit bearing. I do not hear the needle bearing crunching while driving and did not here it in May either. I also attempted to move the unit-bearing up and down thinking the axle seal was toast but it seemed solid at the time.
Today I hear some noise while turning left which lead to the pictures below. Wet side is Driver side, dry side is passenger. Tomorrow morning I should have some time to take a look at this more in depth. Passenger needle bearing was changed last year and no issues since then......
View 14 Replies
I've had the 450 a little over two years. Its used 95% of the time for hauling trailers, including the toy hauler. Has not given me a single problem since day one and now has around 21,000 on the odometer.
Lately I've noticed a "grinding" sound coming from the front end somewhere. It is most apparent when I'm turning at slow speeds; especially left. To describe it would be similar to worn out brake pads or maybe a wheel bearing going bad. It does it whether I'm on the brakes or not.
View 14 Replies
2012 F-250, it sounds like a rock or something in my left front brake cover?? I only hear it when I come to a stop or just start out, sounds like a stone or something coming to rest like if you had a stone in a drying machine coming to rest when you shut it off. But I don't hear it at all over 10mph?
View 4 Replies
I am in the process of replacing the front hub seals so my ESOF works again. I tested both front hubs with a mityvac and neither one of them holds any vacuum at all. All the lines are good, and the pump and solenoid seem to be working fine.
I have the driver's side apart and I have a couple of questions.
What's a good source for the vacuum seal? I've checked rockauto, riff raff, and diesel o-rings. Diesel o-rings has it, but the description says it's only for 2003+ Excursions so I didn't order it.
There is no yellow o-ring anywhere on the hub. I assume that someone forgot to put this o-ring back in and this is why I don't have ESOF? I guess what I really want to know is that there isn't some 2000-specific thing where there's no o-ring, right?
After I got the hub off, I spun it around on my workbench and it doesn't sound good at all. It makes a slight metallic grinding noise about 1/2 way around. I assume this isn't normal? AFAIK these are all original parts - but the missing o-ring means to me that someone already had it apart.
There was a lot of water intrusion and rusty colored grease but nothing was dry, the needle bearings were intact and the shaft isn't scored at all where the bearing rides. I'm hoping new seals and good cleaning and it should be good as new. And then it's off to the next side.
View 7 Replies
So to start at the beginning.... Traveled across Canada East to West towing 11000lb travel trailer, no problem. Have used 4x4 in a few campsites to pull out of a pitch without spinning the wheels and causing damage to the site when it has been really wet. All good.
Got to Banff in December and the town was an Ice rink, engaged 4x4 and all good. Crossed the Rockies and the 4x4 starts making grinding noises. Up and down some mountains and squeaking, grinding noise then clunking.
I have manual hubs, disengage and the noise all goes away. Engage 1 hub and no noise. Engage both hubs, noise back.
I bought some needle bearings and went to swap them. Got hubs apart and they look good. No scoring on the drive shafts. They are not dry, but as I have them open, repack them with grease anyway.
Do more research... Remove ABS sensor and repack main bearings with grease. (broke one sensor pulling it out, too cold plastic brittle oops). Still clunking noises.
The universal joints look good, doesn't appear to be any play in them. However, the axle seal (knuckle seal) (F81Z-3254-CB) does move around a lot in it's metal casing. It is tight on the shaft, but with the hub off, I can move it in and out, and move it side to side. If I had ESOF hubs I guess they would not be locking as I'm sure there would be no vacuum in there!
Question is then, would this seal be allowing the universal joint to wobble under load in 4x4 mode? Would this wobble be the cause of the rumble? As it is labelled as a seal and not a bearing, I wouldn't of thought this would have been a loaded point, and the weight would have been taken by the associated bearings and it could be run without this seal? But if it is not this, then I'm still looking for a clue as to what is making the rumble....
View 3 Replies
My 99 F250 has just recently started making a "rattling" noise. The noise sounds like its coming from the front left wheel area. The noise is constant while driving down the road, its NOT created by bumps or anything, its a constant noise while moving.
View 3 Replies
When I'm in 4 high and I coast I can hear something from the front drive line. It's a soft whirring/grinding type noise.
If I'm accelerating there is no sound . Only when the driveline forces reverse and the engine starts to slow the truck do I hear something.
With my hubs locked but in 2wd I don't hear anything.
Is this something to be concerned about or is it regular noise?
We have had a brutal winter so I've been in 4x4 75% of the time.
View 1 Replies
Problem started with the front end shaking a little bit when braking like the rotors needed turning. Then the brakes began to intermittently hum when stopping. Then my ABS light came on. Put the truck up on the stands and disassembled the brakes on both sides. The ABS sensor was chewed up on the driver side. The less than year old hub felt sloppy so I changed it. Put everything back together.
New hub came with new ABS sensor. Went for a test drive ABS light is gone and I no longer shake or experience the hum when applying the brakes. However now when I go to stop right before I come to a complete stop the driver side (new hub/spindle side) I hear what sounds like the grade school class clown making a fart sound with his mouth, and the truck pulls to the driver side. Is the ABS system malfunctioning or is this a caliper issue? Calipers look like they are OEM.
View 3 Replies
I have a noise with my new (2.6k miles) 2000 Diesel F250 Crew Cab. When I make low speed, right turns while crossing any type of depression in the road I hear a loud knock as if the left shock is bottoming out. There's an intersection near my house with runoff depressions across the road, I almost always hear the noise when making that turn. I've occasionally heard it coming from the right side when making a left turn.
View 14 Replies
2004 PSD 4x4 72k. I thought I would be proactive so I bought the front ball joints and have plans to install them but recently I starting hearing (and feeling) a clicking sound in the front LEFT when I make sharp turns to the left and hit small bumps now and again. I jacked up the front end and am able to get 1/4" of movement front to back (top to bottom so not steering) in the wheel.
I narrowed it down to the hub. I took it apart and it is most likely a sealed unit so no adjustment is possible....that I can see.I pulled out the locking hub and got as far as I can to know there is not an adjustment. Need to confirm that it indeed is a sealed bearing and if so what are the part number(s) I may need to repair it.
View 14 Replies
I've been noticing a grinding coming from the front end of my 2012 f250 4x4, mostly while turning. It seems like its worse over uneven terrain, bumpy dirt roads, things like that, but I have noticed it on occasion while on seemingly smooth roads. Also a couple times while turning and lightly braking I could feel it interfere with the brakes. They wouldn't grab completely and you could feel the grinding in the pedal. I've been crawling around looking for rub marks or any indication of what might be causing it but until recently I hadn't noticed anything. Today though I found this. I'm guessing bad ball joint or tie rod maybe? Maybe just need alignment?
Passenger side lower control arm ...
View 11 Replies
