If front wheel bearings can be greased through the abs wire hole on a f250 4X4, will that work on a sealed bearing on a gm product? I have done my f250 but I also have a 2004 suburban.
View 2 RepliesI have a 2000 F350 4X4 crew cab and have a vibration in the front end. I have done sone investigating and have come to the conclusion that is the front wheel bearings. The dealers says I have to buy the entire hub assemble but I seem to think different. But if I can replace the bearings any special tools that might make it easier ..
View 14 RepliesAre just the bearings serviceable/replaceable or is the only option to get entire wheel hub assembly?
View 14 RepliesI noticed my '12 F250 has grease zerks on the front axle u-joints and was wondering how often you need to grease them ? My truck has 10k on it and while I was changing the oil tonight I decided to give them a few shots of grease until it started coming out of the joint.
View 12 RepliesI have an '06 F-250 that's making a quiet grinding/humming noise from what sounds like the front end. It doesn't seem to be coming from any side in particular, just an omnipresent noise whenever the truck is moving. It's constant with speed, and most noticable between 30-60 KPH.
Truck has about 268,000 KM on it right now, and has been worked pretty hard for whatever that's worth as well.
I am doing the u joints on my 1999 f250 and when I pulled the hub the bearing fell apart in the back. are the rear bearings in the hub replaceable? here is the pic of the bearing that came apart....
View 7 Replies99 F-250 Ext cab 4x4 7.3 285,000 miles.
I got home today opened my door and got snaked in the face with the smell of brakes. I got out of the truck then I heard the drivers side rear brakes popping as they are cooling down. I reached down to touched the wheel and it's crazy hot. Opened the garage and went to retrieve the infared thermometer. The rotor/caliper was 350 degrees, hub was 150 degrees, axle tube was 90 degrees.
I took the wheel off and inspected stuff. The rotors do have some heat spots, the caliper visibly looks okay but not 100%. The pads look like even wear. I am guessing that the caliper either is hanging up or I have a wheel bearing going? The passenger side was like 80 degrees on everything. There is a slight shimmy while driving which to me feels to me like the beginning of warped rotors. I don't hear anything to me that screams wheel bearing noise wise.Brakes or bearings?
I have a 200 f250 v10 srw 4x4.. I've replaced the auto front lockers with warn premium manuals. I cannot get power to the front wheels. The lockers appear fine. I hear the actuator function when I activate 4x4. Whats the possibility of a bad transfer case or front diff and how do i check? I've searched but there seems to be a lot of non-answers.
View 7 RepliesMy rear wheel bearing are a little loose. This afternoon while diagnosing a squeak in the back I found this. While pushing the truck side to side there is a clunk and when you lay your hand on the tire you can feel it, bearings are loose. Nothing during the operation of the truck to give this away, truck runs and drives as it should but I need to check it our before something does go wrong. What I'm looking for is a torque / preload that the rear wheel bearings need to be set at.
View 2 RepliesI have a 2004 F250, CCSB, 6.0L, Fx4, Lariat.
I am trying to replace the passenger side front hub. I either have a bad hub, or I am not installing it properly. I have it installed with the locking hub unlocked and trying to turn the hub, the entire passenger side axle spins. It is also very hard to turn it. I strapped axle, and the hub is almost impossible to turn, with or with out the actual hub installed.
This is the second hub that I installed with the same results. I''m not ruling out bad out of the box, but it is the second one I installed today.
1. Why does my front end hop when only turning right in 4 wheel drive?
2. O nly one of my back tires spin, so does that mean that when I put it in 4 wheel drive I only have 3 tires spinning?
oh I got a 2001 xl 5.4 f250 and is this normal
I replaced my steering gearbox with a remanufactured oem gearbox (no, not the redhead. I wish I'd had the extra money but I didn't.) I replaced the factory sway bar (1.25" diameter) with the Excursion sway bar that came on my axle (1.4" diameter) along with polyurethane bushings and greaseable end links. I replaced wheel bearings, ball joints, track bar bushings, tierods (ends, sleeves, the whole nine yards). Literally everything from the gearbox down, besides the pitman arm, is brand new.
The next day I took it in and got it aligned at Goodyear. The steering is noticeably more responsive, but I still have 1-2" of play either way before I get a response. I'm skeptical about tightening the gearbox. I did that on the old one and it improved steering for a couple years, but this new one shouldn't require any tightening.
I have yet to install new steering stabilizers, but I can recognize bump steer versus this problem on a straight, smooth road. I'm sure the stabilizers won't change the 2 inches of play.
2004 F350 150,000km ... I have a rattling/clicking sound from the front right wheel when the hub is not locked (Free) and I hit small holes or run over rough roads. the sound is gone when I lock the hub front hubs.
View 3 Replies2003 F250 4x4 7.3L
While doing my brakes in the front, I tried to wiggle the front left, nothing. Solid. Then when I did the right, I was surprised to see it wiggle when I grabbed the tire. So I looked to see what was moving.
Not the U joint, not the ball joints, But it looks like what is a drive shaft.. (I am new to this stuff). On the right side a shaft comes out of the axle just before the U joint and the rest of the wheel assy. What is wrong?
Question. My Son borrowed my 2006 4-wheel F-350 and broke down in Vermont. 8 hrs from me. Told me he heard some noises from the left front and then the abs light came on. I had him jack up the front and check for bearing play in the left front. Alas, He said between 1/4" and 1/2" of play. I bought the new hub and bearing assembly to drive up there with tomorrow morning. The locking hub will come right off. I just replaced them 4 months ago. I will be bringing a crap load of tools, but anything specific i should bring? I wont have torches so I am hoping the hub will brake free.
View 3 Replies2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 RepliesI have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 RepliesI have a 2008 F-450 Lariat 6.4 4x4. I recently started noticing the front driver side wheel (best I can tell) wheel makes a noise as though it's binding uo when turning either direction, and I can feel it as well. 4wd is not activated and the hubs are in auto. When the front end is off the ground, I rotated the wheels and they spun independently unless the hubs were locked. I noticed what appear to be seals on both the driver and passenger side hanging loose (see pics). What this might be? I recently used the 4wd when we visited White Sands National Monument while pulling a 5th wheel RV.
View 9 RepliesWell, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
I have a '99 F250 w/ PSD with 165k miles.
When I drive, I move the steering wheel and nothing happens for the first few degrees of turn and then I encounter resistence and it turns. It's the same either way. The vehicle seems to track nicely, doesn't pull to either side, just a lot of slop in the steering wheel.
Is there a way to determine if this is really steering related or is it just loose/worn front end suspension parts making themselves known? My guess is suspension items, but the fact the front end behaves itself when the truck is moving has me doubting that just a bit.