Ford Super Duty (1999-2016) :: Greaseable Sway Bar Bushings And End Links
Apr 30, 2013
I have a 2002 F350 4x4 CC 7.3 i am wanting to change the sway bar bushings front and rear to poly and I want greasable bushings to avoid the squeaking that you get with these bushings alot of the time. I would like to change the end links to poly too i realize these wont be greaseable. What was the outcome and where did you buy the bushings. What is the size of the front and rear sway bars and the length of the end links??
View 14 Replies
Advertisement
I'm on my second set of links. The replacement were Dorman 3 years ago. They are rattling again. Do I just replace them again? I forgot to add, the bushings were replaced this year.
View 1 Replies
What are the specs for the sway bar bushings that go in the retaining bracket for a 2003 ford f250? went to advanced auto last night to get some got mine off my truck and the one they gave me was a little too small for my sway bar and the retaining bracket.
View 2 Replies
Can the hellwig sway bar links will work with an oem sway bar? I need new ones and figured why replace with something I know will fail early...
View 3 Replies
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 Replies
Need recommendation for replacement body mount bushing. Surprised to see the drivers side shredded. Poly replacement?
View 14 Replies
I drive a 2006 Ford F350 4x4 Crew Cab. I think the radius arm bushings on my truck are bad. I get a clunk going over bumps on the left side in the front end.
I'm assuming it is the bushing in the rear of the radius arm, but I haven't taken it apart yet because I want to have the parts in hand. I ordered a bushing, part number 5C3Z3B203AA. But it looks too small when I hold it up to it. What is the part numbers for the radius arm bushings?
Or am I looking at the wrong thing for the clunking in the front end? I just did the ball joints with Moog both sides top and bottom. The shock bushings look alright. I have replaced the front sway bar bushings thinking that was it. What else could it be?
View 4 Replies
We all know the sway bar end link problems in the early superdutys. Several years ago I installed energy suspension bushings and thought the problems were gone. Lately it started clunking again. I tightened the bolts with a breaker bar and it worked. but now it making noise again. I purchased a set of mevotech end links. Upon installation I found the problem.
Over the years of clunking the bolt hole on the upper driver side is no longer round. It has become oval shaped. I read a couple threads on here about this problem. I can't drill them out as the mevotechs have studs not bolts. Can I get the mounting bracket that bolts to the frame. Its a triangle shaped piece that the end link stud goes through. I have tried searching for it online to no avail. Whats it called?
View 7 Replies
Working on my 2000 Excursion, 7.3, 4x4. Replacing front sway bar link arms and sway bar bushings. I got the driver side arm and the sway bar bushings done and have run into a problem removing the passenger side link arm. When removing the top connection bolt there's not enough clearance when extracting. I've gotten it loose, but as I go to pull it off, it butts up against the bell housing with about an inch of bolt left to clear the frame.
View 1 Replies
So putting the new extended links on my truck, not sure if they are supposed to be seated flush on both the frame and sway bar itself before tightening them down. This is how they are sitting now --
You can see a little gap between the rubber fitting where the bushing sits and the frame mount. Just wanted to make sure before I torque it down. Its the same on the other side as well. They are sitting flush on the sway bar.
View 1 Replies
I have a friend with an 01 f250 super duty who needs to replace sway bar bushings.
View 6 Replies
I have a question about my 2001 Ford F250 and the scary road sway I experience on the highway.
I thought it was the garbage and nearly bald tires and the fact that the fronts were bigger than the back, (Previous Owner). I went and got new E rated 265's from Discount Tire.
It actually made the swat feel worse. I thought maybe the tire guys inflated them all to 80 PSI as the sidewalls indicated. I check today and found that they went with the recommended PSI on the door sticker. 60 Front and 80 rear. But this is for the Tire size listed on the sticker.
After the tires cooled here at home I increased the PSI to 80 all the way around. I am having trouble finding my specific problem even though there is a lot of talk in many forums about this issue.
If this does not work should I try lower PSI in the rears and leave the front at 80? Should I try a front steering stabilizer shock? I did tighten up the steering box and took the minor slop out of it, Not is just makes it respond to the sway correction quicker.
View 14 Replies
I was going to add a rear sway bar to make the truck more stable after lifting it but then I thought when I eventually do a cummins swap, with all the torque and the tall block i have in the back ill get a lot of axle wrap so i will need traction bars. So what is the difference between them? will a rear sway bar stop axle wrap as well as body roll? Also will traction bars stop axle wrap and decrease body roll? I just don't want to get a sway bar now and then need traction bars and have to get rid of the sway bar.
View 14 Replies
This is my sway bar and drag link look like with the wheel turned all the way to the right. When I took these pictures, I had put the right tire on the curb too see what it was going too look like. However. Even with all wheels on level ground. It still is running very close. When the steering is straight, I have maybe 1" to 1.5" clearance between the 2. My truck does have a readylift 2.5" level kit on it. Running like this stock or leveled? Should I look around for longer sway bar links?
View 2 Replies
2004 F-250 140k 4wd 6.0. Front end had noise, standard sway bar link knock. I disconnected the sway bar on the drivers side and drove it around. Smooth and noise free. Determined new links were needed, Installed new links and now even more noise. Disconnect them and no noise again. What am i missing? Bushings look good on the axle. Is the pressure from the sway bar putting strain on another wore part?
View 5 Replies
Installing the Hellwig 1 1/4 inch Front Sway Bar on their 11 and up F250 or F350 SRW Pickup?
My 2012 F350 Super Cab LWB XLT 6.7L seems to have quite a bit of sway in the front end. This is especially true moving slowly such as turning into service stations or other off angle turns. The truck only has the FORD OEM puny Rear Anti Sway Bar but the front seems to accentuate sway. The Truck has Rancho 9000XL Shocks, Timbren Enhanced Suspension System as well as Torklift Quick Release Stable Loads in the rear.
The Truck I have is not overloaded but it does carry an Eagle Cap 950 Camper pretty much full time. True the Campers now days are tall so some sway is expected. I just want to reduce the apparent front end sway and wonder if others have used the Hellwig Sway Bar in the front.
View 1 Replies
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
View 1 Replies
I have been having that nice thumping noise that generally accompanies worn out sway bar bushings. I did bushings last spring but a noise came back shortly thereafter. Finally got bothered enough/ found enough time to take a look at it and tracked it down to the sway bar again. My right front axle mount has taken damage before and is now all bent up, not allowing the bushing clamp to hold tight to the bushing. Pictures of the issue are below.
Front view of the entire mount.
Rear view showing the sway bar mount plate.
I am unsure what to do about this mount. As you can see it has been pretty messed up by the PO. What could be done to fix the issue?
View 4 Replies
I've been having the loud clunk under the drivers side floor, that many others have as well. Did many hours of research and replaced the sway bar end links. Napa only had the left side in stock so I did it first last weekend and did the right side this weekend. One thing I noticed when doing the right side was the hole in the frame was all wallowed out. Drilled out the bushing in the upper end link and used a bigger bolt to fill the gap up. went for a drive and the clunk was way worse than it ever was still on the left side. So I took off the left one and went for a drive. Sure enough no clunk, the left one was wallowed out as well. So I did the same thing on that side and the evil clunk is finally gone. Just thought I would throw that out that if have a clunk after replacing the end links, Check the upper holes.
View 14 Replies
I'm scheduled for my first HPDE next week and I just discovered that the bushings on the front end links are worn. I don't notice any issue when taking curves and I'm asking due to the timeline of when the dealer will get the parts...it'll be cutting it close before the event.
View 3 Replies
I plan on replacing as I have a clunk happening. Thought I'd try here first.
Is there a brand that's better? 1Aauto has OEM. Is there a brand that's better or makes a difference?
Or is a front sway bar end link a front sway bar end link?
View 7 Replies
