Ford Super Duty (1999-2016) ::Getting CPS Codes?
Oct 1, 2013
I have a farmer with a 2001 F350 SuperDuty with a 7.3 broke down at his farm a few weeks ago. Asked me to come look at it. No start issue. I use the Matco Determinator in my shop, so I take it with me for starters,after running diagnostics I come up with p0340, p0344,& p1670. After googling these codes I make the determination idm is bad. Farmer agrees to let me try one, install a new BorgWarner unit from O'Reillys, and bam truck fires up. I reinstall inner liner clear codes and go about my way. Few days go by and farmer shows up again, truck run a few miles around farm,spits sputters, and dies again. Go run my checks and same thing. Farmer told me in nthe beginning he had CPS changed per the recall. I had idm replaced under warranty truck fires back up, so this time I drive it , and get bout 2 miles down road truck dies. Had to tow strap back to shop. Got a new cps from ford replaced truck fires up. Farmer takes truck drives for bout a week guess what truck gets towed back. 3 codes are back, along with a few others related to low voltage. This time I replaced idm for a 3rd time, truck fires up. Today I let it idle for 3 hours in lot, decided t test drive, got less than a mile down road, truck shudders chi engine light comes on and it wants to die but keeps running. I am able to get turned around but it dies before I can get back home. Run codes and get same 3.
View 1 Replies
Advertisement
What these codes stand for.
- P1316
- P0640
View 4 Replies
I have a 2003 f350 v-10 drove it yesterday to get fuel, went to start it after fueling. No start, no lights dash was gauged was acting odd, and clicking under the dash from behind fuse box. did get it to start after a while, put my foot on the brake to go into drive, never made it ... truck died I do have remote start system thought it was that with the brake pedal issue. disconnected complete system. no change. Had it towed, home now no nothing, connect a battery and just clicking from under dash no start ?????? not a battery, won't even jump. The battery is good, power to starter, Posted this also in light-duty trucks wrong place think this is the better place. Gauges pinned to right with key off
View 3 Replies
I have a 99 F450. I have an ABS light on. No codes (at least not that my code reader can pickup), but I am also not having any issues. Brakes work fine. What to swap out or where to look?
View 7 Replies
i have p0750 shift solenoid A error and p0733 gear 3 ratio error and i was woundering how i fix them problems
View 9 Replies
05 5.4 F250 4x4. Keep getting those codes. Can't find any vacuum leaks. swapped rear O2 sensors. Fuel filter twice in last 11k miles last time was 1k ago. Will the 430 code cause the lean codes from a bad cat? I've been getting the 430 code for at least 4 mo's.
View 6 Replies
My truck was running fine, it's stock as far as I know. Shut it off, it sat and cooled off for a while. When I tried to crank it, it wouldn't start, threw 2 codes. P2285 and p 2623. I unplugged the icp sensoran tried to start, no start. Plugged it back in and it started fine for the rest of the work day ( I work out of it). Drove it the next day without any issues. Today went to start before work and no start with the same 2 codes. What should I check first? I don't have any monitor yet. Bought the truck a month ago as a work truck. It has 164000 miles.
View 4 Replies
What would be causing my left and right bank lean codes? Truck still seems to run fine. I have also been getting number 6 misfire. all within the past week. I know Its due for a tune up but would a simple tune up fix these codes. Also besides plugs and primary fluids what else should I be changing. I don't want to be getting to involved just the main stuff.
View 5 Replies
2003 f350 2wd 5.4 auto cab and chassis with 40 gal rear tank replaced fuel pump/fuel filter/spark plugs/IAC no codes
View 7 Replies
My 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
View 10 Replies
I just bought a 2007 f250 5.4 V8. It has the codes P0018, P061b, and P2106. The truck seems to run fine but has the codes. Tried clearing but they came back. Also, there's a small howl sound in the rear end. What a solution may be.
View 14 Replies
I have a 2013 F350 Crew Cab Long bed xl with 128000 miles on it. I just barely bought it from a small dealer and had a check engine light come on for the cats.(P0420 and 0430)
I have spoke with the dealer and he assured me that he would replace the cats. He stated he had O2 sensors replaced and thought he had fixed the problem. Not sure if he replaced all sensors or just the fronts.
He has been avoiding calls lately and will not return my messages. Anyways, My question is what should I be looking for to prevent future cats from going bad. I just ordered a bluetooth OBD 2 scanner and bought the Torque Pro App.
I am not new to working on trucks but they have all been 1995 and older and i am new to anything scanner wise and do not know what I should be monitoring. If I can't get this guy to replace the cats I want to monitor everything to make sure the cats are bad.
BTW, Fuel Mileage is at best 12.3 with an extremely light foot, Driving normal it drops off to about 11.8-12. Is this a normal MPG in these trucks? I have seen post about people getting close to 16 unloaded not smashing throttle?
On another note, I just remembered that my traction control light will come on with no wheel spin at times after starting the truck and driving away.
View 14 Replies
I just recently purchased a 2008 ford f350 5.4L gasser, supercab long box. The truck has 167,000km on it. I flew about 700km from my hometown to pick up the truck and drive it home. After driving about 300km I started noticing a few problems.
The engine light codes that have been stored as of now:
P0420 (Catalyst code)
P0420 (Catalyst code)
P0191 (Fuel rail pressure sensor i think?)
The issue I'm having is that the truck has absolutely no power going uphill or accelerating. If I'm climbing a hill and have the gas pedal pushed in at a steady rate its almost as if the transmission wont shift, and if i push harder on the gas the truck begins to shudder. When the truck is cold it runs normal and climbs hills no problem, but once it heats up the problem returns. Another odd thing I noticed under the hood on my drive home was that they disconnected the vacuum line from the fuel rail pressure sensor and simply plugged the line on a random bolt.
Also, the truck apparently has a cam phaser lockout on it and I dont know if that could be causing the issue? Here's a list of some of the troubleshooting ive done so far.
-checked all fuses(start at the basics eh)
-checked resistance of coils(checked out fine, even after engine was warm)
-pulled spark plug 1 and 5, they both seemed fairly clean, not fowled up
-generally looked over all the vacuum lines, seemed fine couldn't see anything else really out of the ordinary
-while the truck was running I used a temperature gauge to see what the exhaust system was doing. On the drivers side when the truck was warm before the cat I had 140C and after the cat it was 80C(good indication the cat is plugged?) The other side tested fairly consistent.
View 9 Replies
I have recently picked up a 2005 F350 with the 5.4, which has 212k on it. Has a check engine light on for P0420 and P0430, as well as some kind of a 'ignition coil 'D'', I forgot which code it was as I deleted them at first to see which would come back. After driving it, the P0420 and the P0430 came back, but not the other, yet probably. I'm guessing the misfire due to the ignition coil caused the cats to go bad and the 420/430 codes, unless these codes are coincidental and the cats went due to high mileage.
Either way, I'm pretty sure I will need to replace the cats and was wondering what is the cheapest route. Should I get individual cats and have a shop weld them on? Should I go to Advance Auto parts or Auto Zone and get the whole pipe with the cats attached to them already and then get them installed? I anything will involve welding, I would have to bring it in to a shop. Also, in regards to the ignition coil misfire, what a good way to check which one it is?
View 4 Replies
Where to start. Have had to replace a few COP's in the past and replaced all spark plugs 20k ago. Truck runs rough at idle and sometimes stalls when changing gear. Strong exhaust smell when sitting idle. If I put my foot in it there is hesitation. Engine seems to smooth out quite a bit but also seems like it's getting more power in stages. Codes P0426 and P0345 ....
View 2 Replies
Ok so my F250 died last night. I read the Pcodes and came up with P2198 and P0506. I am pretty good with fixing the truck but need to know exactly what is wrong.
View 5 Replies
For the last few weeks I have noticed my transmission overheating a bit, nothing bad, but I have just been running around town local so no drives over about 15-20 mins.
Well, Friday night I went out to see a friends band play about 40 mins away, My trans temp climbed steadily the whole way out there, peaking at 226 by the time I got out there. I kinda took my time getting home hopping bars to give the trans a break to cool off.
Did some diagnosis today, first thing I did was unhook the line going to the rear of the transmission and did the bucket flow test. I fired it up and fluid came pouring out of the line which goes into the rear of the trans, nothing really came out of the rear of the trans, it was all out of the line.
So that tells me that its getting flow through the coolers. I didn't measure the amount like some do, but I can tell you it looked like a strong steady flow.
I made sure the fluid levels are proper as well which they are, it was maybe a 1 quart low which shouldn't effect anything. I also inspected the coolers and everything appears to be clean with no airflow restrictions. Took it out for a brief drive again and it climbed up to 147, maybe 5 miles out 5 miles back. Ambient temp is 62 today.
I am getting multiple codes on my Edge Evo which I have had set to stock settings since I bought the truck. Codes I get that concern me relevant to the trans are P0741 and P0743. Both seem to relate to the torque converter.
I feel like my RPMs are a bit to high at highways speeds so I am wondering if I have a TC that is slipping a bit while driving. I did notice a bit of a metallic pearl in the fluid that came out. Aside from that I feel like the trans is shifting ok, though sometimes I have to let off the gas to get it to shift into 4th.
View 3 Replies
99 F-250 SD 6.8 had an issue with it while moving from Del to Phx, Az. Found collapsed air cleaner element. It looked like someone stepped on it. I replaced it as well as the MAF. This fixed the issue. This was 350 miles into the trip. The truck seemed to be down on power as it didn't want to pull my trailer up any type of grade except with OD off. Around 2K miles into the trip in developed a random misfire with no codes. I am at my final destination and the misfire is worse. I am not showing any codes at all or pending either. It is a bit toasty outside to be out there diagnosing issues, and I won't start changing parts randomly either. I have a NGS scan tool with the proper cards.
View 5 Replies
I have a 2012 ford f350 6.7 diesel....I have the following check engine light codes..
P0073 Ambient air sensor circuit high output
P009a Intake air and/ambient air correlation.
I replaced ambient air sensor in passenger mirror and auto zone said to replace the air charge sensor. I have done both still have a check engine light.
View 1 Replies
2008, 5.4 liter, F250, with 6-speed manual transmission
My truck was running fine until I decided to clean my engine. I just wanted to remove the extra dust covering it, so I used a low pressure garden hose to wash away the dirt that had accumulated last winter and spring.
It started throwing codes like Fuel Rail pressure sensors, P0191, P0192. I had no power, and I could hardly drive the truck.
I figured I had some water in some connectors, so I checked around, but could not detect any moisture.
I kept driving it, and the problem got less severe. One warm summer day, I drove my truck for about an hour trip, and everything looked fine after this. Problem never came back.
I was even noticing that it was better on gas that ever before, I was doing 11liters/100km, in city driving.
Until one day (2 months later), I had to disconnect the battery to do some servicing on my truck (more that 30 minutes), and it started to run crappy again, having some piston misfire, throwing codes P2198 and P2196, (O2 sensors). No power, if I am very gentle on the gas pedal, I can manage it, but as soon as i try to accelerate, runs like crap, black smoke coming out of the exhaust.
The problem comes and goes, sometimes, the problem stops, and I can get going, no issues. Air filter is clean, even tried with no air filter, no differences., but it really sounds like bad air/fuel mixture.
View 2 Replies
The engine was just rebuilt, 7.3L diesel. New bottom end, cam and turbo also new harness for valve covers and injectors, new #8 injector(#8 cylinder lost compression). The engine cranks and idles great. Run it up to 1800rpm - 2200rpm and you get a miss or skip. Almost like the engine turns off and back on very quick, and it makes a clank noise. No codes, reading it with a OTC Genisys 4.0. I also swapped the PCM and IDM with another truck and it still does same thing. Other truck runs fine. Year model 2000 w/ 230,000 miles
View 1 Replies
