I think the gear shift lever is loose and so I get a no start every day or two. I remembered seeing somewhere here that there was a way to tighten up the grearshift lever to fix this problem. I did a search to no avail.
View 5 Replies1999 F-350 . My shifter lever is extremely loose, it will not go into park at all. I tightened the two torx bolts, adjusted the needle but its still bad. Im thinking the cable is loose, I saw that there is a small rod attached to the end. Is there a way to tighten it or do I need a new cable assy.?
View 5 Replies2006 350 here. I was wondering if it would be possible to replace my Automatic tranny shift lever with one from a newer truck (08+). If possible, what exactly would need to be replaced?
View 1 RepliesI have a 2003 super duty crew cab 4x4 with V-10 auto w/167k. Awsome truck. I recently have noticed alot of slop in the shift lever on the column. Everything is tight on the tranny end. It appears to be under the dash. Is there a part that may be replacible? And if so... is it fairly simple to repair?
View 14 RepliesIs it common for the exhaust to have a periodic high pitch tinny sound?
View 4 RepliesVolvo Automatic 1992 240 - So, just started to back out of the garage and, all of a sudden, my gear shift got stuck in neutral and then started shifting without engaging the transmission at all. Pushed it back into the space and, taking a look underneath, I realize the control rod's completely detached from the lever in the transmission.
I can re-attach it, but it just comes loose again when I shift. It seems like something should be in there to hold the control rod in place with the transmission lever, but I don't know what because I can't seem to find any documentation on what everything should look like down there.
Attaching a couple shots, one with a circle around the area that's coming un-attached since the angle's a bit off.
Attached File(s)
IMG_8972.jpg ( 1.09MB )
IMG_8978.jpg ( 938.64K )
So it appears as though my shift lever (automatic) will not shift into the 1st gear position? However when I drive the vehicle, the transmission seems to shift through 4 gears, then into Overdrive? What could be the issue?
View 3 RepliesFriend parked his well working truck and when starting it up after sitting a few days it won't shift into any gear. Lever moves as normal but the truck won't move. A soft clicking sound is the only difference to be noticed when shifting the lever. where to start? Temps are below freezing here if that matters.
View 11 RepliesSo when I try to kick into 'passing gear' in this '01 f250 5.4l, i get no tranny shift. Whether I'm in tow/haul mode or not.
View 10 RepliesThe other day I was driving i was driving down the road when suddenly my truck wouldn't shift out of first gear, then the truck died and the motor wont turn over either. Acts like it is locked up. Its an 01 with v10 and 4r100.
View 6 Replies2015 F 250, less then 5k miles. When towing travel trailer, weight 7500lbs, on occasion transmission will not shift out of gear. Happens in first, second, or third. Very intermittent. Take off from a stop engine goes to 6k rpm. Let foot of the throttle goes all the way back to idle, still no shift. Accelerate back up to speed still will not shift. After doing this a couple of times finally shifts. Have had this happen in second and third. Not a lot of fun with cars behind you or trying to merge on highway. No codes
First trip to Ford dealer they re calibrated computer. Still happened towing. Second trip to dealer they put a flight recorder on it and I towed again. Did not hang up in first or second ,but would not shift out of third on highway doing 70mph, even when I lifted from the throttle and coasted. I finally shifted to manual and shifted to fourth and was able to upshift After reading flight recorder mechanic said it appeared normal. I explained that having to shift the transmission manually is not really normal and they agreed.
I may be going to look at a 2001 F250, 4x4 with a V10 engine tomorrow. I think it is a shop truck for a business. The owner said that the mechanics told him that the trans won't shift out of low gear. It is an automatic. Maybe something as simple as a modulator valve (do they still use them)?
View 4 Replies2015, F250 6.2L, 16,000km , so recently my transmission has seemingly lost its mind. When I start it up cold and drive it down my street I am greeted with a horrible slam of a 2nd to 3rd gear shift. Then while towing my TT this weekend a couple of times it held 2nd waaaay longer than it ever has before. Having issues with Torqueshift?
View 7 RepliesI have an issue to where every once in a while my truck will not shift and when it does shift it slams into gear, and my overdrive light flashes and then I'll turn the truck off let it sit and crank it back up and it drives fine and the overdrive light is off. It shifts normal and smooth other than when this happens. Not sure if it is my torque converter or maybe a solenoid or what. My truck is an 07 f250 6.0 with 192,000.
View 5 RepliesOk so I went mudding this past week, and I put my 997 7.3 truck in 4x4 had fun then took it out of 4 wheel now it won't shift past 2nd gear top speed 35 mph.... It still has all the power revs up Rpms fine but it won't go faster then that.
View 8 RepliesSo, in my 99 Bounder RV (F53 chassis), V10
I think it has a 4R100 transmission in it (I have not verified this).
I had the oil and filter changed about 10K ago.
Runs and shifts fine .... then I stop and idle with it in gear (say stopped in traffic for a few minutes).
Now the thing shifts super hard! I actually get rubber in all gears.
So I pull over, shut it off. Restart the unit and everything is fine again.
It does this very consistently!
I went to the local transmission shop. They said with 110K in an RV it could be anything and I should think about letting them rebuild it.
Now that is something I would do ... not diagnose a problem and just rebuild it. I thought a "professional" would actually look for the problem first.
I don't want to rebuild the transmission if there is small item that will fix this.
1999 5.4 ... I was just driving down road and truck suddenly wouldnt shift into overdrive/higher gear. pulled to side of road and the motor was revving very high at 2500 rpm. shut truck off and on a few times...kept doing it until finally after a while it went back to normal....
View 1 RepliesI have a 99 f250 with some procomp (325s) that are 12.5 wide with a 6in lift my superchip tuner can change the trannys shift points but I am pretty sure a new gear ratio is needed. I dont do a whole lot of off roading with it its mainly my driving around and highway rig whats a good gear ratio that would work for me
View 9 RepliesI go out of town for work for a week and come back and my 1999 F250 V10 GAS, is acting up. It started when i tried to drive it and it didn't want to shift, it would rev up to 3000+ RPMs and finally shift really hard into gear along with the speed odo not keeping up and bouncing around not wanting to work. I also had my entire gauge cluster lit up with no key and door closed. all the lights were on and it was "dinging" like the door was open and it wasn't. you would hear it when you put your ear up to the door.
So my first thought was to change the VSS (which I did) no luck. So I started wiggling wire loops under the fuse box in the cab and the "dinging" quit.. i took it for a drive and it works like nothing ever happened. Obviously I am guessing there's a short so i brought it to my mechanic and hes saying he couldn't find anything by the fuse box but he thinks its closer or even attached to the gauge cluster itself. could this be true? Why would the gauge cluster loop throw off the shift points?
I have a '99 F250 SuperDuty Diesel with an Automatic Transmission. There is a button on the end of the gear shift which allows you to turn off overdrive -- in other words the transmission won't shift into overdrive once you press the button.
Here's my problem. I start off driving normally. I've not done nothing to the overdrive button and the truck shifts normally into overdrive. 10-15 minutes down the road, the overdrive light (which indicates the state of the overdrive button) is FLASHING. Pressing the button doesn't stop the flashing. Once this flashing starts, the only thing I notice is a much more abrupt shift from 1 -> 2 gear.
I have an '01 F350 super duty dually, 7.3L, auto trans. Over the past weeks my overdrive light on the gearshift would flash intermittently, maybe once every couple weeks. I chalked it up to a prior theft attempt where the steering column was damaged, and had turn signal/hazards issues after that.
Over the past few days my reverse gear has taken longer to engage, and is hard getting into the higher gears at speed. As of yesterday, reverse is out and won't shift out of second. Fluid level is good and clear. Could this be a PCM issue, or some sensor or relay?