I can't figure out how to get my front brake rotors off to replace them. I removed the caliper and thought the rotors should just come right off but they didn't? I then pulled the hub out and there was a retaining ring with a good size nut behind it , but you shouldn't have to remove the hubs to remove the brake rotors should you?
The stats of the truck are 04 f250 4wd w/manual hubs!
Ok I reinstalled the new rotors and pads clips and warning tabs. The rotors match the old rotors size , thickness and hub clearance. 2 questions
Vehicle still on stands ....
After tightening everything up on the passenger wheel and the rotor seem to have a lot of play or movement... Normal or not ??
Now drivers side hub and lug nut spindle is not moving , possible another issue ....
Passenger side spins freely ....
if I did not have bad luck I would have no luck at all with this truck
I'm trying to replace the front brake rotors on a 97 Ford Explorer (AWD, 5.0 L). I've removed the calipers and pads - but can not loosen the old rotors. It looks held on by rust - but do I need a special rotor pulling tool?
View 8 Replies1999 F350 4x4 dually. Replacing brakes front and back. Rotors, Pads, and hoses. On the left front put rotor back on and torqued down hub nuts on rotor. Then caliper mounting bracket wouldn't fit back between mounting bracket and rotor. Loosened the hub nuts on rotor, and fit mounting bracket in place. Then torqued down the hub nuts again, and rotor rubs on mounting bracket and rotor/hub won't turn.
View 2 RepliesNeed to replace the ac compressor bearing/pulley on my 2001 f350 7.3. My question is do I need a special tool like a pulley puller or is there another way to remove pulley? I already have the clutch assembly removed as well.
View 1 RepliesSo, I bought a set of seat covers yesterday and I'm trying to install them this morning. Surprise, surprise!! The head rests won't come out. I tried pushing the little button and pulling up hard, No good. I look for a little clip or some other retaining device. Nothing. How do I get the front head rests out?
View 5 RepliesHow do I get the front axles out of of the knuckle? It seems like the seals are holding them in? Is there any trick to to getting them out,I am trying to do my ball joints
View 1 Repliesi have a 2008 f250 4x4 i need to replace the drive side front lower body bushing and i can not get the pressed on bushing to come out what is the easiest way to get this to come apart i tried using a 4 ft pry bar and i could not get it to pop free.
View 11 Repliesi've done some searching but haven't found any how-to's or instructions on how to remove the front bumper on my 06 f250. Any link on how to do it?
View 2 RepliesI have a 200 f250 v10 srw 4x4.. I've replaced the auto front lockers with warn premium manuals. I cannot get power to the front wheels. The lockers appear fine. I hear the actuator function when I activate 4x4. Whats the possibility of a bad transfer case or front diff and how do i check? I've searched but there seems to be a lot of non-answers.
View 7 RepliesI have a E99 F350 7.3L 4x4 I know some or most of you have already probably replaced this part and or pulled a front axle shaft out. So here is my question...In the pictures provided you can see what I think everyone is calling a "Dust Seal" and as you can see it is bad and making a very terrible noise when i hit a bump...I was wondering what parts I would need to replace this seal? I tried looking it up and just get lost in all of the other things....I have found write-ups for the axle being removed while changing ball joints but none by it self to just replace this seal.
[URL] ....
I have a lot of play in my front suspension and steering components. At first I thought it was my old tires, so I had them replaced and that worked, but there is still quite a lot of play. I would describe it at loose steering.
I went to get an alignment and they said they couldn't do it because of too much play in the tie rod end.
So that is going to get replaced. What else is down there, bushing wise, that I should replace to eliminate play and rejuvenate my steering?
I am replacing the ball joints on my 07 f250 4x4. got down to the removal of the shaft itself and it won't budge. What is the secret here. Have to go to work on monday, and the weather in Cleveland isn't going to be very good on Sunday.
View 10 RepliesI need to replace the front passenger side wheel hub unit on my 2012 F250 4x4 120,000 mile reg cab truck. Its been a while but I did one on my 2000 F250 without any problems. There should be a few clips inside the hub that hold the looking hub and shaft together, right? Do I need any special tools for this job? What do the bolts need to be torqued to?
View 2 RepliesAre just the bearings serviceable/replaceable or is the only option to get entire wheel hub assembly?
View 14 RepliesAny good info on front brake replacement parts to get better braking out of these beasts? My pads are now needing replacement but I would like to get better performance than that of factory parts....
View 1 RepliesQuestion. My Son borrowed my 2006 4-wheel F-350 and broke down in Vermont. 8 hrs from me. Told me he heard some noises from the left front and then the abs light came on. I had him jack up the front and check for bearing play in the left front. Alas, He said between 1/4" and 1/2" of play. I bought the new hub and bearing assembly to drive up there with tomorrow morning. The locking hub will come right off. I just replaced them 4 months ago. I will be bringing a crap load of tools, but anything specific i should bring? I wont have torches so I am hoping the hub will brake free.
View 3 RepliesThe driver side front body mount bushing on my 2014 is gone which has the grill sitting on the bumper. I started to replace it, but the bolt is sized to the nut. ran off about 1/2 inch and that is it, it will not tighten or loosen anymore.
I cut the head off the bolt, but can not get the body high enough to remove the old bushing so i can cut the nut off flush with the rad support. Now I am trying to get the air filter box out so i can cut the top of the "nut cage" off to remove the bolt and nut out the top. but i can not figure out how it is held in.
I have the intake disconnected and the filter hat off, overflow tank hose disconnected, and two bolts holding the whole thing to the fender out, but it will still not budge. What am I missing here?
I'm gonna replace my front and rear brake pads. Any tips? Do I need to pull the rotor off and clean the axel? I've watched a couple of youtube videos but they leave me with a few answers. I have all the tools, what kinda lubricants will i need? Any recommendations? I hoping I can do a flawless job without and squealing...
View 13 RepliesI own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 RepliesSo I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies