Ford Super Duty (1999-2016) :: Front End Noise When Turned Left Or Right
Mar 1, 2016
2012 F450 Dually King Ranch 4x4 - I have read many threads on front end noise. I started hearing a noise when I turned left or right and then slowly run over a speed bump. I listen to music at an average sound and I picked up on the front end noise. For some reason you can hear it in the driver seat better.
Anyway I took the vehicle in and the mechanic said he didn't hear anything. I thought, he forget his hearing aid today? I have this expensive warranty plan that would actually cover a few items in the front end but Ford is claiming they don't hear anything.
In their defense I have figured it out why. When the temps are below 40 the noise gets louder and I think by the time they looked at it (8 hours after I brought it in, 5:00pm) the day was warmer.
View 11 Replies
Advertisement
Last couple drives I have noticed some front end noise on the left side. Back in May I also noticed grease all over behind the rotor. I believe this is the grease inserted via ABS hole into the unit bearing. I do not hear the needle bearing crunching while driving and did not here it in May either. I also attempted to move the unit-bearing up and down thinking the axle seal was toast but it seemed solid at the time.
Today I hear some noise while turning left which lead to the pictures below. Wet side is Driver side, dry side is passenger. Tomorrow morning I should have some time to take a look at this more in depth. Passenger needle bearing was changed last year and no issues since then......
View 14 Replies
2012 F-250, it sounds like a rock or something in my left front brake cover?? I only hear it when I come to a stop or just start out, sounds like a stone or something coming to rest like if you had a stone in a drying machine coming to rest when you shut it off. But I don't hear it at all over 10mph?
View 4 Replies
TRUCK: 2003 F250 S/C Long bed 4x4 7.3 Diesel
PROBLEM: grinding noise in left front when slowing and stopping.
Starts as a howling noise, turns into a grinding as you brake and come to a stop. I feel it in the pedal and as it slows it feels like metal to metal brakes
WHAT HAVE WE DONE: Replaced both front hub assemblies (MOOG)... Replaced dust shields, rotors, calipers, pads as well as all new brake hardware.
At any speed when I brake hard it grinds and howls, I have taken out the 4x4 locking hub assembly and it does not change the situation. I am stumped!
View 6 Replies
I replaced both front bearings, calipers, brake pads, now I have a grinding noise on the left side front stops sometimes when you step on the brakes? 1999 F350 ...
View 6 Replies
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 Replies
My 99 F250 has just recently started making a "rattling" noise. The noise sounds like its coming from the front left wheel area. The noise is constant while driving down the road, its NOT created by bumps or anything, its a constant noise while moving.
View 3 Replies
I have a noise with my new (2.6k miles) 2000 Diesel F250 Crew Cab. When I make low speed, right turns while crossing any type of depression in the road I hear a loud knock as if the left shock is bottoming out. There's an intersection near my house with runoff depressions across the road, I almost always hear the noise when making that turn. I've occasionally heard it coming from the right side when making a left turn.
View 14 Replies
2004 PSD 4x4 72k. I thought I would be proactive so I bought the front ball joints and have plans to install them but recently I starting hearing (and feeling) a clicking sound in the front LEFT when I make sharp turns to the left and hit small bumps now and again. I jacked up the front end and am able to get 1/4" of movement front to back (top to bottom so not steering) in the wheel.
I narrowed it down to the hub. I took it apart and it is most likely a sealed unit so no adjustment is possible....that I can see.I pulled out the locking hub and got as far as I can to know there is not an adjustment. Need to confirm that it indeed is a sealed bearing and if so what are the part number(s) I may need to repair it.
View 14 Replies
I just picked up a 2005 SC LB 4x4 5.4 v8 6mt F-350 yesterday and drove it about 250 miles home. It is my first Super Duty, and I love it so far but... the steering has some issues. There seems to be decent amount of play in the steering wheel when I'm driving straight. Also, the truck drives straight when the steering wheel is turned about 30 degrees to the left, and I would like to fix that and bring it to center. When I was cruising on the highway (65-70 mph), there was also two 20 minute periods of time spaced an hour apart where the steering would get light and the truck would dart to the left (i do not think road conditions were a factor as it did not happen on the worst stretches of highway. The truck has 133,000 miles on it, and has had pretty routines maintenance done on it, as it was owned by a drilling business as a work truck to haul tools. The guy I bought it from said that it needed the steering shock/damper replaced, so I will do that, but what else to you think I need to do to the truck?
View 2 Replies
So the other day i opened the door and heard a super loud clunk noise come from the door and when I turned the car on and pulled hte window down it wouldn't go down all the way, only about 75% of the way so I assumed like BMW cars the window motor died but oddly it continued to go up and down just now 100% down.
Then 3 days later when I came to drive the car again the window went down to the 75% mark and now its jammed there with no movement even if I tried to lift the window up myself. Usually a broken motor allows this to happen but since it isn't budging I am wondering if its an electrical issue with the power window button more than the motor?
I say this because when i try to lower the passenger window from the driver side it works than out of no where on the 3rd time it wont move at all than 5 minutes later it will move or if it doesn't move I just go and pull the window down from the passenger side then I come to the driver side and try it and it works again than it'll stop again. So maybe its the power window control buttons on the drivers side that's failing?
View 2 Replies
I noticed a slight whistle last year coming from my front left hub. I pulled the hub and greased the gears as best I could and it sort of went away. Now this year it is a little louder. It only happens when the hub is locked. Is starts around 20mph and goes away at 40. Is the bearing in the hub shot or is this normal. 4x4 works fine and there is no visible excess wear on the gears. The truck has 93k.
View 6 Replies
1999 F250 SD 4x4 7.3 PSD ... My truck has 198K miles on it. It pulls to the left as I drive it. So I took it to a shop to have the alignment checked. They told me that the front outer tie rod was bad and needed to be replaced. And of course they said they needed to put in a set of caster camber bushings to do the alignment. They quoted $400 to change the tie rod out. I said I would do that. They gave me the print out from the alignment but reading it the only thing that was out was the toe. Left tire was toe out and the right tire was toe in, which to me would cause it to pull to the left.
I got under the truck and the steering link, piece that goes from steering box to right side/tie rod, is not tight...I can move it up and down and it clunks when I roll it up. I have a clunking noise when I drive it and go over bumps also. Could this be the clunking noise? Also, if I replaced the ends of the steering link, that would tighten up but possibly push the steering back to the right some to straighten out the tires? I have read alot of threads talking about the clunking being tied to the sway bar bushings being bad but the clunking I get by rolling the steering link up and down sounds alot like the noise I am hearing.
Also, when looking at the axles where they go into the knuckle, there is a loose plastic ring on both sides. Is this part of the dust shield or an oil seal?
View 5 Replies
I have a 99 F-250 extended cab superduty 4 wd with the 7.3. I also plow during the winter. Recently I've noticed wear on the inside of the left front tire. Brought it to a tire shop and had them check the front end and alignment. They told me that the specs were "within" tolerances" for my truck. I'm stumped as to why the abnormal wear if everything is supposedly good with the alignment.
View 5 Replies
1999 F350 4x4 dually. Replacing brakes front and back. Rotors, Pads, and hoses. On the left front put rotor back on and torqued down hub nuts on rotor. Then caliper mounting bracket wouldn't fit back between mounting bracket and rotor. Loosened the hub nuts on rotor, and fit mounting bracket in place. Then torqued down the hub nuts again, and rotor rubs on mounting bracket and rotor/hub won't turn.
View 2 Replies
I drive a 2006 Ford F350 4x4 Crew Cab. I think the radius arm bushings on my truck are bad. I get a clunk going over bumps on the left side in the front end.
I'm assuming it is the bushing in the rear of the radius arm, but I haven't taken it apart yet because I want to have the parts in hand. I ordered a bushing, part number 5C3Z3B203AA. But it looks too small when I hold it up to it. What is the part numbers for the radius arm bushings?
Or am I looking at the wrong thing for the clunking in the front end? I just did the ball joints with Moog both sides top and bottom. The shock bushings look alright. I have replaced the front sway bar bushings thinking that was it. What else could it be?
View 4 Replies
I have a 2014 f250 with the my ford touch radio. In February I had to have the audio control module replaced because it was shorting out internally. Since then I've had a crackling noise in my speakers when the radio is turned up over half way. I'm about to drop it off at the dealer for the 3rd time and I'm going crazy!
View 12 Replies
So my truck is making a rapid clicking type of noise out of the vents when the ac is turned on.
The noise sounds like a thin piece of paper getting hit by a fan (that's what I hear) It started during this past winter when I would cold start the truck. but as the heater warmed up it went away completely. well now since its warm out I am running the ac now, and it blows cold but doesn't have a lot of volume to it it seems. but being the problem was when the truck was cold running the cold ac makes the noise permanent.
The blend door acutator is working as should (i can only assume the blend door is ok) the vacuum lines are good and vacuum signal is good.
View 7 Replies
I have an 04 F250 6.0L and for the last month or so when I turn on my AC it makes a high screetching noise but only last for a little bit. Had a friend that works on cars on the side take a look at it one day and he said it was the AC cutch trying to engage. Does this sound like what it could be? Also if it is can it be changed out without having to remove the compressor? What all is involved in changing it out?
View 5 Replies
Its a rotational squeak, that sounds like its under the cab or possibly left front tire. The truck only has around 25k miles on it. I recently had a 2" leveling kit installed, 35" tires, and rear airbags installed (within 5k miles). I checked the universals and they seem to ok and there is no noticeable clunk. I am hoping its something small.
View 7 Replies
Having a problem with calipers again/still seems like always. Replaced all calipers twice in 86K miles on a 2000 f250 crew 4x4 because of stuck calipers. Replaced brake hoses and all hard lines in the rear about 2 years ago. My problem now is the left front caliper is not squeezing hard enough to stop the truck evenly. (pulls to the right) The rotor had some rust from sitting and after driving a for a while the rust is not completely gone as you would expect. Replaced caliper bled a couple of times. Caliper looks to be getting pressure enough to bleed and can see it move when brakes applied when engine not running. I don't have experience with Proportioning Valves but do you think that is the problem and how do I fix it?
View 8 Replies
