I am not up on the exact operation of the hub lock/unlock on superdutys but when following them, I can see the front axles still turning with the wheel. So even with them "disengaged" they still turn with the wheels?
If that is the way they are designed to do, why? Seems like efficiency could be gained by having them actually disengaged when not needed. And save wear on the inner housing seals.
I have a strange thing going on with my hubs i think. I have a 2000 f250 7.3 4x4 that I just purchased. Lettering on hubs were worn out as far as labeled locked or unlocked so I tried to turn the axel to see what position they were in. Drivers side spun freely but passenger side did not. Both hubs were counter clockwise and turning it to lock didn't change a thing.
Figured it was a bad hub so I jacked the front drivers side up. Spun tire with both hubs unlocked and axle didn't spin. Locked hub on drivers side and axle spun. Indicating the passenger side was unlocked. Then I locked passenger side and wheel would not turn. Ok. That seems right.
Jacked up passenger side front tire with drivers side on ground and axle spins no matter if its locked or unlocked. So does this indicate the hub is good and I should look at something else or could it still be the hub. Axle spins all the time and I don't want to wear anything out.
I have a 2015 F250, cc 4X4 PSD. It has 22,000 miles on it. I notice a small quarter sized drop of oil after it is parked by the right side front wheel. It is coming from behind the dust cover and universal joint where the axle goes into the tube. I dont know how long it has been leaking. My issue is I am about 800 miles from home on a camping trip, have to go back to work Monday, and lcoal dealer here can't take it in till next week. So, if the hubs are not locked and the truck is in 2 wheel drive, the gears shouldn't be turning right? I assume it is ok to drive home. I didn't want to pull the plug and check the fluid because if any runs out and leaves a stain on the cover, I don't want ford trying to deny warranty claiming I messed with it first.
View 5 RepliesCheck out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 2 RepliesI have a slight problem and don't know how serious it is. I own a 2003 F350 with a lift kit. After my drive shaft shattered last September. due to a U-Joint a clicking noise started up in the front axle area after we locked the hubs so we could crawl it down the road out of traffic.
What would be the likely causes and how much would a typical repair/replace cost?
I noticed the other day after my truck was parked on a bit of a angle there was diff oil from the passenger side on the ground. reading a bit on here i learned the axle seals are way in the front housing close to the front diff. and yesterday driving a heavy load around my front brake driver side got stuck on a bit and over heated and was smoking, couldn't even touch the rim it was so hot. anyway about this axle seal i got the hub off right now but cant seem to pull out the axle assembly through the knuckle but i see i have to pry and most likely wreck that seal. Looking for a link of piuctures or how to replace the axle seals in the housing.
View 11 RepliesIt's the Right Front Axle Shaft on my 2006 F250 where it goes into the Hub/Bearing assembly.
Seems way to loose to me but after I removed the Lock-Out, I discovered the Axle Shaft is held in by a Snap-Ring not a Nut (WTF) so how do I get this tightened up
Also it's my understanding (I didn't remove) between the Axle & Steering Knuckle there's a rubber O-Ring. Could all this play be from that O-Ring being wasted Although that doesn't seem likely to me, Iam worried what's wrong
So the other day I took my locking hubs out and cleaned them really good. When they were out I noticed I could grabs axle shafts inside the hub and wiggle them quiet a bit. Is that normal?
View 2 RepliesI have my front axles out to replace the U-Joints but they are rusted in there. Even the C-Clip is fused/rusted in place. I use my flat wheel grinder and ground out the C-Clips but the U-Joint caps wont budge. Been soaking in penetrating oil too. Any way other than drilling them out?
View 1 RepliesI have an F250 4.2 diesel 4x4 double cab. Its a2005 model. I noticed an oil leak from the front left axle. It looks like its leaking from the axle tube. See pic attached. Is a seal probably worn? How big a job is this to fix.
View 4 RepliesHow do I get the front axles out of of the knuckle? It seems like the seals are holding them in? Is there any trick to to getting them out,I am trying to do my ball joints
View 1 RepliesI'm trying to figure out how much of my front end I need to rebuild. 130,000 mi on the truck. About 1/2 of those miles are off road. 2008 F350 FX4. Stock. Original front wheel bearing unit and hubs. I was under the truck today and before I put it on jacks I decided to see how much play was in the front end components.
I noticed when checking out the passenger side front axle at the u-joint that I was able to spin the whole u-joint and bearing with the wheels still on the ground. I wasn't able to do the same for the driver's side. Both hubs were set to auto although I know that the ESOF doesn't work. Is this normal? Am I supposed to be able to spin the axle with the wheels on the ground?
99, F250, 4X4, V10, 72,000 miles. I have had the front axle seals replaced three times in the past 3000 miles, and the right continues to leak. My mechanic screwed up three times?
View 6 RepliesCheck out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 Replies99, F250, 4X4, V10, 72,000 miles. I have had the front axle seals replaced three times in the past 3000 miles, and the right continues to leak. My mechanic screwed up three times?
View 10 RepliesLooking for a complete exploded parts diagram for the front axle on a 1999 4X4 F-250?? (If possible from the wheels inward.) Having some issues and really need this.
View 8 RepliesWith the front hubs locked locked I get a ticking noise out of the front axle almost like there is rocks in the hubcaps. But unlock the hubs and the noise goes away. Also, if I put it in 4 wheel with the hubs unlocked i get no noise.
View 12 RepliesTried converting the 10 lug to 8x6.5 and didn't work. so now i found a 2000 F450SD 8x225mm monotube front axle but just got my hands on a '99 F350 4.10 DRW axle 8x170mm....can I bolt the 8x170 hubs (spacers as its a dually front axle) up front? not sure if the bolt pattern on the rotor will work...
I was thinking adapters up front as i can widen the front track abit if i had to, but dont want to go 170mm to 225 adapters out back, as i think its too much weight for those... I will have a front 90 F-superduty 10 lug set up....
Just wondering if its normal that my front axle sits out about 1 1/2 inches further on the drivers side than the passenger, also gas pump always shutting off when filling up...
View 6 RepliesI noticed my '12 F250 has grease zerks on the front axle u-joints and was wondering how often you need to grease them ? My truck has 10k on it and while I was changing the oil tonight I decided to give them a few shots of grease until it started coming out of the joint.
View 12 RepliesI own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 Replies